Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Results 1 to 20 of 172

    Hybrid View

    1. #1
      Join Date
      Oct 2004
      Location
      Indiana
      Posts
      1,371
      The bellhousing is magnesium. The clutch is a 5 lb. 5.5" carbon fiber triple disc clutch and an 8 lb steel flywheel . The reason we don't need a "traditional" 38 lb. .250 wall steel bellhousing is the rotating mass of the small diameter lighweight carbon clutch/flywheel is exponentially smaller than the traditional 12" diameter clutch/flywheel unit that weighs 50lbs. When a 50 lb/12: diameter mass rotating at 8000 rpm decides not to do that anymore, it takes that thick hunk of steel to prevent limb amputation. If the 13 lb/5.5" unit come apart, the most painful thing is the sound of your checkbook being pried open [again].



      The additional benefit of the lightweight clutch is that this engine gains RPM like an F1 car. It will see 8000rpm on a simple throttle blip. And the street manners are not terrible. It takes a little getting used to, but I would easily drive this thing in city traffic. Another benefit is that this unit will control up to 1200 lb ft. of torque.

      Downside? This Tilton unit is around $7,000. I found mine on ebay off a used ARCA racer for $1500. It took a little thought and machine shop time to mate everything up correctly, but that's what hotrodding is!

      For those who want a "bolt it in and go" solution...we recently put a Centerforce Dyad clutch in the 48 Hour Camaro. THAT is a nice piece...and it drives like butter!

      Man, that was a longassed answer to a simple question, wasn't it?
      Bret Voelkel
      Director of Innovation Fox Powered Vehicles Group
      Founder/ Former Owner
      RideTech/Air Ride Technologies, Inc.

      How do you spell Impossible?


    2. #2
      Join Date
      Dec 2009
      Posts
      261
      Country Flag: Canada
      Quote Originally Posted by bret View Post
      ...Downside? This Tilton unit is around $7,000. I found mine on ebay off a used ARCA racer for $1500. It took a little thought and machine shop time to mate everything up correctly, but that's what hotrodding is!
      The other thing about the carbon/carbon clutches is the material tends to shred rather than shatter, so in the event it goes ejection is even more unlikely.
      I got my quartermaster version off a (now defunct) ASA racer, it's supposedly already set up for an LS motor. What did you need to do to get it on an SBF?

    3. #3
      Join Date
      Oct 2004
      Location
      Indiana
      Posts
      1,371
      Well...the clutch itself had the correct spline for the Rankin NASCAR trans we used [can't remember the exact spline right now] so that was fine. We used the LS flywheel it came with and redrilled the bolt pattern for the Ford crank. This engine is a zero balance unit so that was not a big deal either. The only real trickery was getting a bellhousing/starter/ring gear to work together. The bellhousing that came with my ebay find was for an LS engine so that was a non player. I found a mag bellhousing on ebay but it was for a larger flywheel system that couldn't work with the tiny clutch. So...we used an LS flexplate, redrilled it for the Ford crank [like the flywheel] and sandwiched it between the flywheel and the crank, making all the neccessary spacers/pilot hubs, etc.
      Worked perfect!
      Bret Voelkel
      Director of Innovation Fox Powered Vehicles Group
      Founder/ Former Owner
      RideTech/Air Ride Technologies, Inc.

      How do you spell Impossible?

    4. #4
      Join Date
      Jun 2011
      Location
      Jasper, IN
      Posts
      92
      Country Flag: United States
      The steering rack and radiator are back on and it looks like its going to be at Nashville this weekend! And if not we've always got a backup (1969 Silver Mustang)















    Advertise on Pro-Touring.com