Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Page 8 of 9 FirstFirst ... 3 4 5 6 7 8 9 LastLast
    Results 141 to 160 of 170
    1. #141
      Join Date
      Dec 2008
      Location
      Lehigh Valley Pa
      Posts
      1,269
      Ok I have beed told I should have some kinda radiator shroud. So I made one. Just a quickie but looks ok.













      I also wired up my fan temp switch, lengthened the wires for my altenator to reach the other side. I hope to have her running maybe tomorrow. Also did a shakedown run of my hauler and everything seems fine.
      1996 Federal Cadillac hearse
      1988 Eureka Chevy hearse

    2. #142
      Join Date
      Dec 2008
      Location
      Lehigh Valley Pa
      Posts
      1,269
      Blew the engine at RTTS. No regrets. Besides I got my money's worth out of that $400 engine and then some. More later when I am rested.
      1996 Federal Cadillac hearse
      1988 Eureka Chevy hearse

    3. #143
      Join Date
      Nov 2005
      Location
      Little Rock, Arkansas
      Posts
      945
      Very sorry to hear it. But at least your's died having fun. Mine crapped out just driving down the road. Time to build one bigger and better buddy.

    4. #144
      Join Date
      Dec 2008
      Location
      Lehigh Valley Pa
      Posts
      1,269
      Quote Originally Posted by critter View Post
      Very sorry to hear it. But at least your's died having fun. Mine crapped out just driving down the road. Time to build one bigger and better buddy.
      It died having alot of fun and will be back. Probably throw the orginal 307 back in just so it can be on the road for now. need to get some 1/2 inch thick exhaust manifold flanges made. Twins may be on the way.
      1996 Federal Cadillac hearse
      1988 Eureka Chevy hearse

    5. #145
      Join Date
      Dec 2008
      Location
      Lehigh Valley Pa
      Posts
      1,269
      Final pics before heading out to RTTS. Here are the aluminum hood hinges and final bumper mountings. Must be VERY careful closing the hood.








      1996 Federal Cadillac hearse
      1988 Eureka Chevy hearse

    6. #146
      Join Date
      Dec 2008
      Location
      Lehigh Valley Pa
      Posts
      1,269
      Well here is the next piece of the puzzle. Since my engine went at RTTS I had to figure out what to do next. And this helps me get to the next point. It's a 330 forged crank that is cut for a 3.5 stroke. So I am on my way to a 375 stroker engine.
      1996 Federal Cadillac hearse
      1988 Eureka Chevy hearse

    7. #147
      Join Date
      Dec 2008
      Location
      Lehigh Valley Pa
      Posts
      1,269
      Well I got my flanges in for the manifolds. Have to say they are pretty darn nice. I will be getting the weld els probably next week. So one step closer to my turbo manifolds.


      1996 Federal Cadillac hearse
      1988 Eureka Chevy hearse

    8. #148
      Join Date
      Dec 2010
      Location
      Apex, NC
      Posts
      1,020
      Country Flag: United States

    9. #149
      Join Date
      Nov 2005
      Location
      Little Rock, Arkansas
      Posts
      945
      Daaahm. How thick are they?

    10. #150
      Join Date
      Dec 2008
      Location
      Lehigh Valley Pa
      Posts
      1,269
      They are 1/2 inch thick. I didn't want any sealing or warping issues due to heat.
      1996 Federal Cadillac hearse
      1988 Eureka Chevy hearse

    11. #151
      Join Date
      Dec 2006
      Location
      SF Bay Area
      Posts
      463
      Holy stink-a-mony! I have never seen flanges that thick! How hot does an Olds run?

      chunger

      '68 Ranchero 500
      '70 Cougar XR-7 Convertible
      '98 Mustang GT Convertible


    12. #152
      Join Date
      Dec 2008
      Location
      Lehigh Valley Pa
      Posts
      1,269
      Quote Originally Posted by chunger View Post
      Holy stink-a-mony! I have never seen flanges that thick! How hot does an Olds run?
      Well they will be for Turbo manifolds. I look at it this way. How many times have you heard "my headers leak cause the flange to thin" And these manifolds will be supporting the turbos. Not to mention they may need to be ground flat after welding so I have more material to work with in that circumstance. I don't want to have to do this twice because I bought something that wasn't strong enough.
      1996 Federal Cadillac hearse
      1988 Eureka Chevy hearse

    13. #153
      Join Date
      Aug 2004
      Location
      Rustburg, Virginia
      Posts
      3,436
      Country Flag: United States
      You could mill another 1/8" off to make sure they are true/flat ...thickest I've seen were 3/8" then you could use standard length exhaust bolts.
      1970 RS/SS350 139K on the clock:
      89 TPI motor w/ 1pc rear seal coupled to a Viper T56 via Mcleod's modular bellhousing w/ hydraulic T/O bearing from the Viper, 12 bolt rear w/ 3.73 gearing, SC&C upper control arms, factory lowers with Delalums, C5 brakes at all four corners, Front Wheels 17x8's with Sumi 255/40/17 and Rear Wheels 17x9's with Sumi 275/40/17.
      Brief description of the work done so far can be found here: http://www.nastyz28.com/forum/showthread.php?t=112454


    14. #154
      Join Date
      Dec 2008
      Location
      Lehigh Valley Pa
      Posts
      1,269
      Hey I actually got something done today. Since I have owned the car the passenger side rear door has never worked. Well now it does. Kinda. It will open from the inside. But I need the plastic clip that goes over the rod and into the handle for the outside to work as well. I never saw a need to fix it realy because it never got used. The reason I fixed it? Well it's time to start on the door panels. I have seen other peoples work and want to give it a try. So I took off the front passenger side panel. Stripped it down to the door card. I was going to coat it with fiberglass resin while on the car figuring that would help it hold its shape. But even then it looked wavey. So I took it off laid it on the bench and used a cylinder head to hold it down and put a layer of fiberglass cloth and resin where it was flat. when it is fully cured I will do another section. Then once I get them all done like this I will decide on how I was it to look. I would like to redesign the arm rest and make it look better. I also took a look at doing my airdam splitter. Think I have it figured out for the most part. Just have to start making all the pieces to put it together. I am going to make two noses. One for street use where the splitter will be 5 inches off the ground. And one where it will be 2 inches off the gorund for track days. I amd going to make it all a quick change arrangement where the bumper, airdam, and splitter are all one piece and can be unbolted easily from the outside.
      1996 Federal Cadillac hearse
      1988 Eureka Chevy hearse

    15. #155
      Join Date
      Dec 2008
      Location
      Lehigh Valley Pa
      Posts
      1,269
      Look what I did today. This is just the start of the piece to fill the gap between the nose and radiator support, cover the top of the rad support, and cover and support the top of the radiator.

      I also did some more work to my door cards. I am going to have to decide how I want my door panels to look soon.
      1996 Federal Cadillac hearse
      1988 Eureka Chevy hearse

    16. #156
      Join Date
      Nov 2005
      Location
      Little Rock, Arkansas
      Posts
      945
      Cool!

    17. #157
      Join Date
      Mar 2007
      Location
      Florida
      Posts
      2,391
      Country Flag: United States
      I like the idea of being able to swap out the bumper/spoiler combos. Excellent idea!

    18. #158
      Join Date
      Oct 2006
      Location
      McKinney, TX
      Posts
      899
      Country Flag: United States
      What did you use to get your base in under the fiberglass?
      Confucius says, "Choose a job you love, and you will never have to work a day in your life"

      My build Beast

    19. #159
      Join Date
      Dec 2008
      Location
      Lehigh Valley Pa
      Posts
      1,269
      Quote Originally Posted by absintheisfun View Post
      What did you use to get your base in under the fiberglass?
      Simple cardboard. It really works well. The resin soaks into it making it part of the piece. Allows you to use less fiberglass and is strong if you do both sides.
      1996 Federal Cadillac hearse
      1988 Eureka Chevy hearse

    20. #160
      Join Date
      Dec 2008
      Location
      Lehigh Valley Pa
      Posts
      1,269
      Ok I got a little more done to the radiator support cover. It is really coming along, Today I got the top part of the radiator done. There are a few spots I intentionally didn't do. I will get to them in finer detail when it's off the car. Once this sets I will remove it do some trimming and put a layer under it and then it should be plenty strong.








      1996 Federal Cadillac hearse
      1988 Eureka Chevy hearse

    Page 8 of 9 FirstFirst ... 3 4 5 6 7 8 9 LastLast



    Advertise on Pro-Touring.com