Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Results 1 to 13 of 13
    1. #1
      Join Date
      Mar 2006
      Location
      Lowell, MI
      Posts
      403
      Country Flag: United States

      9 inch center section leaking.

      Anybody have any suggestions to help keep my center section from leaking gear oil from the flange. I've had the center section in and out of the car probably 5-6 times over the past few years and no matter what I try, it always seems to seep from the flange/studs. I've tried gasket with RTV, I've tried no gasket and just RTV. No luck. I always clean both surfaces with solvent and wire brush the studs clean. I always use Ultra Black RTV as well. Still wants to drip on my garage floor, drives me nuts!

      Turbo Charged LS1/T56

    2. #2
      Join Date
      Mar 2008
      Location
      Chicago suburbs
      Posts
      667
      Country Flag: United States
      There is one called "lube locker" that may work for you. Or you could try to seal the studs individually



    3. #3
      Join Date
      Apr 2012
      Location
      Woodstock, IL
      Posts
      2,410
      Country Flag: United States

      9 inch center section leaking.

      You could also try putting crush washers under the nuts.
      SchwartzPerformance
      The leader in bolt-in muscle car chassis
      SchwartzPerformance.com | GMachineChassis.com | Facebook | Twitter | Instagram

      Dealer for: Forgeline, RideTech, Tremec, American Powertrain, Silver Sport Transmissions, GM Performance Parts, RECARO, Cerullo Seats, TMI Products, Vintage Air, Baer Brakes, Wilwood, BeCool, AFCO, Tanks Inc, Holley / Hooker, Ultimate Headers, Rick's Tanks, Moser Engineering, Currie, TechAFX, Stainless Works, II Much Fabrication, and many more

    4. #4
      Join Date
      Sep 2010
      Location
      Orange County, CA
      Posts
      675
      I had the same problem with my 12 bolt cover leaking. Edelbrock Gasgacinch stopped the leak. It is really strong, it was very difficult to remove the cover again.

    5. #5
      Join Date
      Mar 2006
      Location
      Lowell, MI
      Posts
      403
      Country Flag: United States
      Thanks for the suggestions guys. I do have crush washers under the nuts but they have been on and off so many times that they are probably not working like they should. Anybody know where to source them from? I'll look into that Gasgacinch stuff.

      Turbo Charged LS1/T56

    6. #6
      Join Date
      Sep 2010
      Location
      Beach Park IL
      Posts
      3,059
      Country Flag: United States
      Quote Originally Posted by another69 View Post
      There is one called "lube locker" that may work for you. Or you could try to seal the studs individually
      Quote Originally Posted by Schwartz Performance View Post
      You could also try putting crush washers under the nuts.
      Both of those.
      Donny

      Support your local hot rod shop!

    7. #7
      Join Date
      Feb 2008
      Location
      Denver NC
      Posts
      288
      Country Flag: United States
      What kind of nuts? What brand gasket? I've encountered leaks when the stud fits poorly into the housing or the holes in the gear case are too big.... if the nuts are coming loose try these
      https://www.zoro.com/nord-lock-lock-...73/i/G4345092/
      Need A T-101,Jerico or other 4 speed transmission serviced? Pm me....

    8. #8
      Join Date
      Apr 2001
      Location
      The City of Fountains
      Posts
      16,129
      Country Flag: United States
      Permatex Aviation Sealer.

      Andrew
      1970 GTO Version 3.0
      1967 Cougar build
      GM High-Tech Performance feature
      My YouTube Channel Please Subscribe!
      Instagram @dr__efi
      I deliver what EFI promises.
      Remote Holley EFI tuning.
      Please get in touch if I can be of service.

      "You were the gun, your voice was the trigger, your bravery was the barrel, your eyes were the bullets." ~ Her

    9. #9
      Join Date
      Dec 2010
      Location
      Fredericksburg, VA.
      Posts
      3,164
      Country Flag: United States
      It may not be your gasket at all, you may need to remove each stud and seal them individually.
      Steve Hayes
      "Dust Off"
      68 Camaro

      Support the RPM Act
      https://www.sema.org/rpm-faq.

    10. #10
      Join Date
      Mar 2006
      Location
      Lowell, MI
      Posts
      403
      Country Flag: United States
      I did narrow it down to the gasket interface. I hosed everything down with brake cleaner to get everything squeaky clean. Then let it sit for a couple days. Slowly the gear oil started seeping out of the gasket. I re-cleaned it and ran a fresh bead of RTV over the area (I really didn't want to take the center section back out lol). So far it's still dry after sitting for a few weeks. Fingers crossed. I did order a new gasket and new copper washers as a back-up plan.

      Turbo Charged LS1/T56

    11. #11
      Join Date
      Nov 2012
      Location
      ocala fl
      Posts
      302
      Country Flag: United States
      Do not use brake clean to clean the surface. Use brake clean or laquer thinner. I had that problem before and was told that brake clean leaves a film that most sealers can't stick to it.My moser leaks between the housing and the cnter section. I used brake clean and the better black sealer and last time I checked it had not leaked.

    12. #12
      Join Date
      Sep 2016
      Location
      Winnipeg, Manitoba, Canada
      Posts
      21
      Country Flag: Canada
      Had the same problem with my Strange 9 inch diff. Was sealed with RTV the first time it leaked and it lasted 4 years. The second time we used Detroit Diesel grey sealer and hit the surfaces with a light emery after using brake clean, to clean and give a little grip to the sealer. Has not leaked in a few months. I bought the copper stud washers but haven't put them on, if leak starts again will add them.

    13. #13
      Join Date
      Nov 2012
      Location
      ocala fl
      Posts
      302
      Country Flag: United States
      Permatex makes a sealer called The Right Stuff. It is a gasket sealer to replace a gasket. I had an oil pan leak . I had to pull the motor way up in the air and remove the trans, scatter shield to get it high enough to clear the cross member. Still had the leak. I cleaned all the surfaces with good lacquer thinner. I ended up cleaning the pans sides with brake clean and then lacquer thinner and put this stuff along the sides of the pan. It doesn't leak any more. Also used it the same way on my leaking 9" and no leaks so far! It looks terrible on the yellow pan but I will put up with it till I have to take something apart.




    Advertise on Pro-Touring.com