Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Page 3 of 3 FirstFirst 1 2 3
    Results 41 to 49 of 49

    Thread: Clutch slipping

    1. #41
      Join Date
      Aug 2004
      Location
      El Dorado Hills, CA
      Posts
      789
      Country Flag: United States
      Ouch I feel your pain Justin. I am beginning to have some trouble with my setup too. I'm hoping its a simple clutch adjustment. But we will see.

      Brad
      68 Camaro - Procharged LQ4 coming - Currie 9" narrowed, bagged, lays frame, BMW projector HID's LED tails, 18"s, lexus center console, seat warmers, A/C... Mini-tubbing in progress!!

      07 BMW 750li -loaded


    2. #42
      Join Date
      Sep 2004
      Location
      Wisconsin
      Posts
      247
      Well as of now I have pput the 11 inch McLeod clutch in upon initial start up of car it wouldn't go into gear very well or at all. So I adjusted to take some free play out. The throw out bearing is either just touching the fingers or about 1/100th of an inch away. Regardless it is driveable at least for now. I'll try and put some miles on it to shake bugs out, I plan on hitting the last 3 days of the Power Tour. Now I'm nervous! hahhaha Aren't we all!!
      Justin
      --------------------------------------------------
      73 Nova, 502 ci, TKO600, Mosier Eng 12 bolt, 6 point roll cage, Wilwood rear discs, factory front discs, 250 HP nitrous, subframe connectors, Slide-a-link trac bars, 17" Boyd Coddington Smoothie II's, and Hotchkis TVS kit.

    3. #43
      Join Date
      Apr 2001
      Location
      The City of Fountains
      Posts
      16,130
      Country Flag: United States
      What ball stud are you using?

      Andrew
      1970 GTO Version 3.0
      1967 Cougar build
      GM High-Tech Performance feature
      My YouTube Channel Please Subscribe!
      Instagram @dr__efi
      I deliver what EFI promises.
      Remote Holley EFI tuning.
      Please get in touch if I can be of service.

      "You were the gun, your voice was the trigger, your bravery was the barrel, your eyes were the bullets." ~ Her

    4. #44
      Join Date
      Sep 2004
      Location
      Wisconsin
      Posts
      247
      Hey Andrew,
      I am using the bracket from Scoogin Dickey that bolts to the bellhousing. When I used the bracket for the ball stud, the Z Bar was to long. As the Scoogin Dickey bracket must stick out further than just the ball stud would if it was screwed into the block. So I shortened the Z Bar about 3/4 inch. But I did make sure to scribe a straight line on the Z Bar prior to cutting it in half to make sure I got the correct ration when welding it back together.

      Justin
      Justin
      --------------------------------------------------
      73 Nova, 502 ci, TKO600, Mosier Eng 12 bolt, 6 point roll cage, Wilwood rear discs, factory front discs, 250 HP nitrous, subframe connectors, Slide-a-link trac bars, 17" Boyd Coddington Smoothie II's, and Hotchkis TVS kit.

    5. #45
      Join Date
      Apr 2001
      Location
      The City of Fountains
      Posts
      16,130
      Country Flag: United States
      I meant the ball stud in the bellhousing.

      Andrew
      1970 GTO Version 3.0
      1967 Cougar build
      GM High-Tech Performance feature
      My YouTube Channel Please Subscribe!
      Instagram @dr__efi
      I deliver what EFI promises.
      Remote Holley EFI tuning.
      Please get in touch if I can be of service.

      "You were the gun, your voice was the trigger, your bravery was the barrel, your eyes were the bullets." ~ Her

    6. #46
      Join Date
      Sep 2004
      Location
      Wisconsin
      Posts
      247
      ??? I got the whole manual kit from CC5S and I beleive they outsource there pedals and stock repro stuff from someone like Classic Industries. So the ball stud itself is either a GM part or a repo GM part. What are you thinking?
      Justin
      --------------------------------------------------
      73 Nova, 502 ci, TKO600, Mosier Eng 12 bolt, 6 point roll cage, Wilwood rear discs, factory front discs, 250 HP nitrous, subframe connectors, Slide-a-link trac bars, 17" Boyd Coddington Smoothie II's, and Hotchkis TVS kit.

    7. #47
      Join Date
      Apr 2001
      Location
      The City of Fountains
      Posts
      16,130
      Country Flag: United States
      If the clutch fork is not close enough to the clutch fingers than the geometry would not allow the full release of the clutch.

      Andrew
      1970 GTO Version 3.0
      1967 Cougar build
      GM High-Tech Performance feature
      My YouTube Channel Please Subscribe!
      Instagram @dr__efi
      I deliver what EFI promises.
      Remote Holley EFI tuning.
      Please get in touch if I can be of service.

      "You were the gun, your voice was the trigger, your bravery was the barrel, your eyes were the bullets." ~ Her

    8. #48
      Join Date
      Sep 2004
      Location
      Wisconsin
      Posts
      247
      It was an adjustable peice that in the CC5S kit instructions said to adjust ball stud so that clutch fork sits resting at roughly 5-7 degrees. I did this to the best of my ability as far as angles. Does anyone have any measurements that I can take in regards to "roughing" this thing in! I'm past my normal mechanical ability and need a few "guidelines" Thanks guys!

      Justin
      Justin
      --------------------------------------------------
      73 Nova, 502 ci, TKO600, Mosier Eng 12 bolt, 6 point roll cage, Wilwood rear discs, factory front discs, 250 HP nitrous, subframe connectors, Slide-a-link trac bars, 17" Boyd Coddington Smoothie II's, and Hotchkis TVS kit.

    9. #49
      Join Date
      May 2005
      Posts
      209
      Justin
      The 5 to 7 degree thing is approximate and as long as you are close to this it will be fine. The problem you are having is a linkage geometry issue. You are correct in that we don't make the pedals and linkage so we don't have any way to control quality but they have proven to be a good product in the past, however mistakes do happen! I would try to check the linkage compared to stock GM linkage if you can. Distance from the pivot point to the rod holes and the distance from the clutch pedal pin to the hole in the pedal. Moving the hole on the pedal an inch closer to your foot or moving the clutch pedal push rod hole in the Z bar closer to the shaft will increase the stroke and solve your problem but it will increase pedal effort. Before you do anything make sure your clutch pedal is coming up right to the stop and make sure it travels to the floor with no obstruction. Thick floor mats or carpet that prevent the clutch from full travel can be a problem thats easy to overlook. Also remove the rubber stop for the clutch pedal and adjust the free play again. This will give you about 1/2 inch more travel. If you would like me to call you e mail me and I'll try to help you sort this out.
      Last edited by GMJim; 05-09-2008 at 11:29 AM.

    Page 3 of 3 FirstFirst 1 2 3



    Advertise on Pro-Touring.com