Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Page 2 of 3 FirstFirst 1 2 3 LastLast
    Results 21 to 40 of 49

    Thread: Clutch slipping

    1. #21
      Join Date
      Aug 2001
      Location
      Connecticut
      Posts
      1,572
      Country Flag: United States
      Are you using an adjustable pivot ball on the fork? (thinking so that you can adjust for a block plate, etc if it is a lakewood bell housing.) Just a thought... -Dan

      1968 Camaro RS/SS, LS7 with Katech mods, T56 Magnum, C6Z06 Brakes
      1968 Camaro RS Convertible LS3/480hp/4L70E
      1962 Corvette 327-340hp stock
      1963 Corvette Split Window Coupe
      1967 Corvette L79 convertible
      2006 Corvette Z06
      2011 Corvette GS convertible



    2. #22
      Join Date
      Aug 2004
      Location
      CHICAGO SUBURBS
      Posts
      761
      I installed a clutch in a Camaro, rated for 4-500 horsepower. Broke it in nice. As soon as I put power to it in 3-4 gear it turned it into shredded wheat. If the clutch had been slipping it might be toast. Also there are 2 different clutch arms sold as fitting by the clutch makers. I ended up getting a third one from a resto house that has a GM part number on it. The third one works the best.

    3. #23
      Join Date
      Sep 2004
      Location
      Wisconsin
      Posts
      247
      The clutch is a McLeod Dual Friction and the presure plate is whatever comes in the CC5S kit. Yes it has a adjustable ball stud. I actually started off with the longer clutch fork (which is the correct one for big blocks supposedly) and then had these isues and then installed GMs shorter version of the fork.

      When I had the first clutch fork in (longer) I had prolly 700 miles on regular driving and went to kind of do a little fishtail and when I layed on the throttle smoke just flew so I thought hey awesome, the tires are frying so I grabbed another gear and more smoke, but the car never did fishtail. Why? Because instead of tire smoke, it was clutch smoke. I didn't know until I slowed down for intersection and got a smell of the smoke! Yuck I hate clutch smoke!!

      I really wouldn't know how to tell if it was the wrong pressure plate. But I do know everything else seems to be legit. The one thing that I do know seems incorrect is the Z Bar linkage. To me it seems as if its at an angle slightly from motor to frame. But I have the correct amount of travel on the pedal. So maybe it is pressure plate related! What a pain in my ars!
      Justin
      --------------------------------------------------
      73 Nova, 502 ci, TKO600, Mosier Eng 12 bolt, 6 point roll cage, Wilwood rear discs, factory front discs, 250 HP nitrous, subframe connectors, Slide-a-link trac bars, 17" Boyd Coddington Smoothie II's, and Hotchkis TVS kit.

    4. #24
      Join Date
      Sep 2001
      Location
      Accord, NY
      Posts
      2,295
      Country Flag: United States
      Have you spoken with McLeod?
      69 Camaro convertible, 410, M22, 8-pt cage therapy program. SOLD.
      68 camaro - SOLD
      67 Bel Air - New street project with perfect floors, frame and trunk!

    5. #25
      Join Date
      Sep 2004
      Location
      Wisconsin
      Posts
      247
      Not directly with McLeod, I have been talking to CC5S and they haven't seen this problem yet. Maybe it would be worth while to call McLeod and see what they have to say.
      Justin
      --------------------------------------------------
      73 Nova, 502 ci, TKO600, Mosier Eng 12 bolt, 6 point roll cage, Wilwood rear discs, factory front discs, 250 HP nitrous, subframe connectors, Slide-a-link trac bars, 17" Boyd Coddington Smoothie II's, and Hotchkis TVS kit.

    6. #26
      Join Date
      Nov 2006
      Posts
      24
      If its a ZZ502 the flywheel we sell for that is .840 thickness. Thats the measurment from the crankshaft flange to face.

    7. #27
      Join Date
      Sep 2001
      Location
      Accord, NY
      Posts
      2,295
      Country Flag: United States
      The McLeod FW is .850

      When I spoke with them ([email protected]), we had some good discussion on hp levels vs disc recommendations. I went with the 12" setup and their 260173 for my 500 HP 410 sbc.
      69 Camaro convertible, 410, M22, 8-pt cage therapy program. SOLD.
      68 camaro - SOLD
      67 Bel Air - New street project with perfect floors, frame and trunk!

    8. #28
      Join Date
      May 2005
      Posts
      209
      Justin
      Call me Wednesday afternoon and we can discuss this a little further. I have some ideas but their too long for typing with two fingers on the forum. 905-896-9744

    9. #29
      Join Date
      Sep 2004
      Location
      Wisconsin
      Posts
      247
      Sounds good Jim. I'd like to get this gremlin nipped in the rear before spring is here and maybe help others along the way!

      Justin
      Justin
      --------------------------------------------------
      73 Nova, 502 ci, TKO600, Mosier Eng 12 bolt, 6 point roll cage, Wilwood rear discs, factory front discs, 250 HP nitrous, subframe connectors, Slide-a-link trac bars, 17" Boyd Coddington Smoothie II's, and Hotchkis TVS kit.

    10. #30
      Join Date
      Sep 2001
      Location
      Accord, NY
      Posts
      2,295
      Country Flag: United States
      Let us know the outcome!
      69 Camaro convertible, 410, M22, 8-pt cage therapy program. SOLD.
      68 camaro - SOLD
      67 Bel Air - New street project with perfect floors, frame and trunk!

    11. #31
      Join Date
      May 2005
      Posts
      209
      Justin
      Have a look at this thread. http://www.camaros.net/forums/showthread.php?t=102842

    12. #32
      Join Date
      Sep 2004
      Location
      Wisconsin
      Posts
      247
      Well I have tried all of the drilling in the world and it has netted me nothing. I have actually drilled the Z-Bar and clutch pedal so much I have the connector rod as short as it gets and I have to pull up on the clutch pedal firmly to get the rod to connect. So I have pretty much rulled out the linkage needing to be longer. This is getting so frustrating. I have only like 600-700 miles on this dang thing. I have it adj so far that it BARELY goes into gear. I just about have to put my foot through the floor and then it still is clunky and even then it slips. Arggghhhhh.... Anyone!!!! Maybe you all feel this way to, but how come this sh@# always happens to me! I love this hobby. (some sarcasm there)
      Justin
      --------------------------------------------------
      73 Nova, 502 ci, TKO600, Mosier Eng 12 bolt, 6 point roll cage, Wilwood rear discs, factory front discs, 250 HP nitrous, subframe connectors, Slide-a-link trac bars, 17" Boyd Coddington Smoothie II's, and Hotchkis TVS kit.

    13. #33
      Join Date
      Dec 2006
      Location
      California
      Posts
      1,368
      Country Flag: United States
      I'm having a similar problem. I have grinding while going into 2nd and reverse. I've tried lengthening the clutch rod and even with no free play (as soon as I press the clutch pedal, it starts disengaging) it still grinds a bit. But if I shorten it, I can't get it into gear at all.

      Other than this issue, I love the tranny. It's just that I can't drive it hard because of it. I can press the clutch and move the shifter left and right a few times and then shift into reverse and it'll be fine. I can also hold the clutch in for 2-3 seconds before shifting into 2nd and it won't grind, so I don't know what's going on.

      Matt

    14. #34
      Join Date
      Apr 2006
      Posts
      23

      F.w.i.w.

      Not wanting to sound patronising. If the clutch will clear and allow you to engage gears while stationary and start to grab a little off the floor then the adjustment should be ok. This is provided there is a little (say 1/8"--1/4") of pedal freeplay before the throw out bearing touches the pressure plate. The same freeplay set up as you would for the brake push rod to m/cyl.

      To test the clutch, drive the car in fourth gear at 35 mph and flatten the throttle. At the same time (while you are at W.O.T.)jab the clutch pedal to the floor and immediately release the pedal.

      The R.P.M. will jump of course and if the clutch is healthy when the clutch is released the R.P.M. will be pulled down almost immediately.

      If the clutch is not good, the test proceedure will result in a slower apply or a slipping sensation. A slow apply will indicate a damaged clutch plate or a clutch that needs more clamping force.

      This is old school from an almost retired mechanic in Australia so I hope it helps.
      It's hard to be sincere with a poor memory

    15. #35
      Join Date
      May 2005
      Posts
      209
      Justin
      Give me a call. I'll see if I can help you out.

    16. #36
      Join Date
      Sep 2004
      Location
      Wisconsin
      Posts
      247
      Grandpa Ronsy,
      Yes that is about the very same "Top Secret Test" that I use to see how the clutch grabs. Basically when I'm doing 35-40ish and put the throttle down and stab the clutch you can hear the RPM come up right away and then it drops. So the clutch slips for about 1 to 1.5 seconds before actually engaging.

      GMJim,
      I just got your PM and this post, today (Memorial Day). So as it is a Holiday I will have to wait until tomorow to get in touch with you.
      Justin
      --------------------------------------------------
      73 Nova, 502 ci, TKO600, Mosier Eng 12 bolt, 6 point roll cage, Wilwood rear discs, factory front discs, 250 HP nitrous, subframe connectors, Slide-a-link trac bars, 17" Boyd Coddington Smoothie II's, and Hotchkis TVS kit.

    17. #37
      Join Date
      Aug 2004
      Location
      El Dorado Hills, CA
      Posts
      789
      Country Flag: United States
      Hey Justin any updates on your slipping issues?
      Brad
      68 Camaro - Procharged LQ4 coming - Currie 9" narrowed, bagged, lays frame, BMW projector HID's LED tails, 18"s, lexus center console, seat warmers, A/C... Mini-tubbing in progress!!

      07 BMW 750li -loaded

    18. #38
      Join Date
      Aug 2004
      Location
      El Dorado Hills, CA
      Posts
      789
      Country Flag: United States
      Hey Justin, did you get it fixed?
      Brad
      68 Camaro - Procharged LQ4 coming - Currie 9" narrowed, bagged, lays frame, BMW projector HID's LED tails, 18"s, lexus center console, seat warmers, A/C... Mini-tubbing in progress!!

      07 BMW 750li -loaded

    19. #39
      Join Date
      Sep 2004
      Location
      Wisconsin
      Posts
      247
      Well here goes, another long winter and still no working clutch. To make things short I posted here just in case anyone wanted to know the history or extent of this process.

      So this past fall I got a new clutch to try and replace the one I had. basically I had a long talk with Jim at CC5S and we came to the conclusion that maybe the 12" clutch was to large in diameter and not allowing the clutch to move far enough in my application. So I went with the 11" clutch from McLeod. I installed that last week (long winter and I built a Harley and cut damn wood and plowed damn snow all winter) and after installing the 11" clutch I started the car and this god awful squealing started going on. I shut the car off immediately and adjusted clutch out because I thought there was to much tension on TO bearing. Then upon starting it up again the same or worse squealing noise. So I backed car back into the garage and took tranny out. Sure enough the TO bearing had seized up. So I bought a new Centerforce TO bearing that is in the same self centering design as the original TO bearing GM had. Stuck this in adjusted clutch so that I had a 1/4 inch at the fingers and TO bearing and 1/2 to 3/4 inch pedal play and thought all was better.

      So this morning I finished bolting in cross member and driveshaft and started the car up. It won't even go into gear. So I have yet to try it but if I go any tigther with the TO bearing to gain more clutch wont the TO be riding on the fingers all the time and where it out fast? So much drama for this damn thing. The good news is that this TO bearing isn't locked up.

      So........... Any new suggestions?
      Justin
      --------------------------------------------------
      73 Nova, 502 ci, TKO600, Mosier Eng 12 bolt, 6 point roll cage, Wilwood rear discs, factory front discs, 250 HP nitrous, subframe connectors, Slide-a-link trac bars, 17" Boyd Coddington Smoothie II's, and Hotchkis TVS kit.

    20. #40
      Join Date
      Apr 2001
      Location
      The City of Fountains
      Posts
      16,130
      Country Flag: United States
      Quote Originally Posted by 73novaguy
      .....

      So........... Any new suggestions?
      Justin,

      I am really sorry that you are having all of these issues. Here is my suggestion. I am sure many will disagree and offer other alternatives. Personally I have never liked the mechanical z-bar arrangement in the older cars. My suggestion is that you convert to a hydraulic setup. I just did this recently as part of the upgrades on my GTO. I have an LSx engine and a Richmond 6 speed, but that is irrelevant. The setup I am using will work for your application and the proceedure for setting it up correctly will also be the same. Here are some more details:

      https://www.pro-touring.com/forum/sh...t=40904&page=5

      If the bellhousing that you are using has a big access panel on the bottom it will make life a little easier, but you can do it without it. It is imperative that you are maticulous in setting up the hydraulic bearing.

      Good luck.

      Andrew
      1970 GTO Version 3.0
      1967 Cougar build
      GM High-Tech Performance feature
      My YouTube Channel Please Subscribe!
      Instagram @dr__efi
      I deliver what EFI promises.
      Remote Holley EFI tuning.
      Please get in touch if I can be of service.

      "You were the gun, your voice was the trigger, your bravery was the barrel, your eyes were the bullets." ~ Her

    Page 2 of 3 FirstFirst 1 2 3 LastLast



    Advertise on Pro-Touring.com