Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Page 1 of 6 1 2 3 4 5 6 LastLast
    Results 1 to 20 of 106
    1. #1
      Join Date
      Apr 2011
      Location
      North NJ/SW Virginia
      Posts
      197
      Country Flag: United States

      1970 Pontiac Lemans Update

      Okay, here this goes.

      I bought the car when I was 15, and since then I have been doing simple stuff. Its a 1970 Pontiac Lemans with a P350, 2bbl, 350 trans, & 8.2 10 bolt. Its a real nice, original car with only 38,000 original miles so I'm going to cut it up. Last fall I began to work towards a pro-touring car, but things have been moving slow. Its hard to get stuff done on the budget of a high school student, and it won't get any easier next year when I go to college, so it will be slow going. I hope to turn my old Pontiac into a reliable daily-driver to use at college, I'm not going to make a street-fighter or a big money car, just a competent street car.

      Here is the suspension plan:
      • UMI front upper control arms w/ 1/2 inch tall ball joints & delrin bushings
      • UMI front lower control arms w/ delrin bushings
      • UMI rear upper & lower control arms w/ roto joints & adjustable
      • UMI drive shaft loop
      • UMI rear control arm braces
      • Lee 670 steering box
      • re-valved power steering pump
      • new Lee rage joint
      • lower it a bit (not sure yet how much)
      • hotchkis sway bars front & rear (already in car)


      Here is the drive train plan:

      • aluminum radiator w/ electric fans
      • convert 2 bbl carb to 4 bbl (already have in boxes, just need to put in car)
      • swap original 2.78 gears of something a little more fun
      • put shift kit in the trans
      • 2.5 stainless steel exhaust (already done)


      As far as the interior goes, its all their and pretty much all original. I pulled the original bench (made a sweet couch) and put in some scat pro car seats. I replaced the speedo because it was the only gauge which didn't work, but now all the other gauges decide to stop so they will get completely replace with some new ones. It also needs a console, so I'll make one and put a floor-shifter on it. Its currently a column-shift, and the wiring in the steering column is funky so ill just replace it with a new one. I also want to put down some form of sound deading, maybe dynamat?

      Here is what I have some questions on:
      • brakes: everyone here loves kore 3 so I've been looking at their stuff, but i have heard good things about the CPP big brake kit
      • steering column: flaming river or ididit?
      • wheels: this is where it gets tricky, I would love wheels like NewGen lite III's (ones on vengeance) but they cost a lot. I also like the Year One 17inch Rally II's and their cheap. Any other wheel suggestions? How wide can I go with rubber on a stock frame up front and out back? (I'm thinking 275 out back but I'm not sure what to do in the front)
      • I also need a smaller steering wheel, any suggestions?




      Here are a few photos of what I'm working with:
      Name:  photo(1).jpg
Views: 14214
Size:  250.5 KBAttachment 58183
      Click image for larger version. 

Name:	photo(2).jpg 
Views:	9263 
Size:	196.2 KB 
ID:	58184
      Click image for larger version. 

Name:	photo(3).jpg 
Views:	9969 
Size:	269.0 KB 
ID:	58185
      Click image for larger version. 

Name:	photo(4).jpg 
Views:	9713 
Size:	260.5 KB 
ID:	58186
      Click image for larger version. 

Name:	photo(5).jpg 
Views:	9308 
Size:	269.4 KB 
ID:	58187




      Unfortunately major updates will be few and far between, but I'm still moving forward.

      That should be it for now, thanks for looking.

      John

    2. #2
      Join Date
      Feb 2012
      Location
      the Netherlands
      Posts
      76
      Country Flag: Netherlands
      Nice and original Le Mans you got there!
      It's pretty rare to see such an old car with only 38K miles.
      Manuel Compaan
      the Netherlands



    3. #3
      Join Date
      Feb 2005
      Location
      Sydney, Australia
      Posts
      1,797
      Country Flag: Australia
      Any of the repro Formula factory steering wheels would look nice, and they feel good. Lecarra does a Formula looking wheel but in leather...very nice!
      I have the Year One 17x9 Honeycombs...they are a really nicely made wheel....so I'm betting the Rally II 17's would be the same...great value and would really look right on your car....as would the Honeycombs.
      Personal suggestion....don't lower it any while you're using it as a daily driver...its low enough as it is for regular use...think speed humps and driveway entries etc. The suspension work to make it handle is a great plan.
      For brakes....I've heard good stuff about Kore3...if you want to go budget on the back, try a Master Power Brakes conversion kit for 11" drums....complete bolt on B body big finned drums, cheaper than a disc conversion and would match larger front discs nicely.

      Its great that it looks good...detail up the paint, get some good quality wax on there like a couple of coats of Meguiers etc. Don't get tempted to go crazy on the outside...doesn't need it, looks great the way it is....save the tight budget for mechanical/suspension and interior stuff.

      Good luck with it!
      Regards,
      Leigh

      Sydney, Australia
      1971 Firebird 455

      https://www.pro-touring.com/showthre...Project/page27

    4. #4
      Join Date
      Sep 2007
      Location
      Southern California
      Posts
      566
      Country Flag: United States
      For a column, go with a factory column. They made that car with a floor shifter, so they can be found. (My family had a 70 lemans for years. I wish I had gotten it when I was 15!) Another reason for the factory column is that it is collapsable. In the event of an accident the column is designed to slide forward if your body hits it. At the same time the steering shaft is designed to collapse in an accident. Get yourself some morris 3 point belts as well. This will make the car safer for a daily driver and they bolt in.
      Jon U.

      1968 GTO - SC&C Suspension, Forgeline SO3 Wheels
      Build Thread
      1967 911 with a few mods

    5. #5
      Join Date
      Jun 2010
      Location
      Philipsburg, Pa
      Posts
      545
      Awesome car... I am huge Leman's fan. We are redoing a 1972 now to use for some testing, auto cross and show.

      Enjoy and thanks for including us in your project!
      Attached Images Attached Images  
      Ryan
      UMI Performance
      www.umiperformance.com
      814.343.6315

      Join us on Facebook!

    6. #6
      Join Date
      Apr 2011
      Location
      North NJ/SW Virginia
      Posts
      197
      Country Flag: United States
      Ryan when is UMI bringing back the 15% off sale? I missed it last year and I'm hoping ones coming up soon.
      John McLoughlin
      1970 Pontiac Lemans
      https://www.pro-touring.com/showthre...-Lemans-Update

    7. #7
      Join Date
      Jun 2010
      Location
      Philipsburg, Pa
      Posts
      545
      Hello John, Unfortunately you won't see any sales or promotions until mid summer sometime. This time of the year is prime season so we have trouble keeping up with orders as it is, everyone is trying to get their car ready right now!

      If you decide to go with one of our suspension kits listed on our site they have a 10% off savings built into them.

      I hope that helps,
      Ryan
      Ryan
      UMI Performance
      www.umiperformance.com
      814.343.6315

      Join us on Facebook!

    8. #8
      Join Date
      Apr 2011
      Location
      North NJ/SW Virginia
      Posts
      197
      Country Flag: United States
      Ok I've ordered the 17 inch Rally II's. Now I need to decide on tires. Currently I have BFG Radial T/A's which are 225/70 r14s. These are 26.5 inch tall and I want the new tires to be around this size. I have narrowed my tire choice to Nitto 555, I just need to pick a size. 255/45 r17 which are 25.94 inches tall or 255/50 r17 which are 27.09 inches tall. Any opinions? Both are around half an inch off the current size so it probably won't make a difference. I just want another opinion.
      John McLoughlin
      1970 Pontiac Lemans
      https://www.pro-touring.com/showthre...-Lemans-Update

    9. #9
      Join Date
      Dec 2007
      Location
      Atlanta, GA
      Posts
      54
      Country Flag: United States
      I am running 17x9 rims with the NITTO 555; 255-45 Front and 285-40 Rear on a 1970 Firebird Formula. If you are alright with not being able to rotate them, then I think the wider tire on the rear of the LeMans with its wide rear quarters would look great. The 15" stock rims and tires were about 26" tall on the 1970 Formula and TA, I bet the LeMans was similar.
      Mark Z.
      1968 Firebird
      2016 Mustang GT w/ Performance Pack
      2014 BMW X5 Turbo V8, AWD Highway Cruiser
      1970 Firebird Formula 400 (Gone but never forgotten)

    10. #10
      Join Date
      Apr 2011
      Location
      North NJ/SW Virginia
      Posts
      197
      Country Flag: United States
      Do you think a 285/40 r17 tire would fit under the rear of a Lemans without any rubbing
      John McLoughlin
      1970 Pontiac Lemans
      https://www.pro-touring.com/showthre...-Lemans-Update

    11. #11
      Join Date
      Dec 2007
      Location
      Salem, OR
      Posts
      226
      Quote Originally Posted by john31s View Post
      Do you think a 285/40 r17 tire would fit under the rear of a Lemans without any rubbing
      With the right wheel backspacing they should fit no problem. The wifes' LeMans has 275/40/17 and I have 285/40/17 on the rear of my Cutlass. They both have 245/45/17 on the front. I think I could (barely) fit 315 tires on my car if I had the exact right backspacing.
      Mike R
      '66 Olds Cutlass Convertible
      '15 Challenger SRT 392 (DD)
      '72 Pontiac LeMans (wife's toy)

    12. #12
      Join Date
      Apr 2011
      Location
      North NJ/SW Virginia
      Posts
      197
      Country Flag: United States
      The wheels have 5 inch back spacing (I'm 90% sure). Would that fit?
      John McLoughlin
      1970 Pontiac Lemans
      https://www.pro-touring.com/showthre...-Lemans-Update

    13. #13
      Join Date
      Apr 2001
      Location
      The City of Fountains
      Posts
      16,130
      Country Flag: United States
      Quote Originally Posted by john31s View Post
      Do you think a 285/40 r17 tire would fit under the rear of a Lemans without any rubbing
      Yes, easily. I run a 295/40-18 on a 18x10.5 wheel with 6.25" of backspacing. I do have the fender lip rolled slightly, but that is mostly to give it a soft edge in case it does rub, which it never has.

      Andrew
      1970 GTO Version 3.0
      1967 Cougar build
      GM High-Tech Performance feature
      My YouTube Channel Please Subscribe!
      Instagram @dr__efi
      I deliver what EFI promises.
      Remote Holley EFI tuning.
      Please get in touch if I can be of service.

      "You were the gun, your voice was the trigger, your bravery was the barrel, your eyes were the bullets." ~ Her

    14. #14
      Join Date
      Apr 2011
      Location
      North NJ/SW Virginia
      Posts
      197
      Country Flag: United States
      Ok but would it fit on a 17x9 wheel with 5 inch spacing? I don't want to have to use spacers on the rear.

      John McLoughlin
      1970 Pontiac Lemans
      https://www.pro-touring.com/showthre...-Lemans-Update


    15. #15
      Join Date
      Apr 2001
      Location
      The City of Fountains
      Posts
      16,130
      Country Flag: United States
      Quote Originally Posted by john31s View Post
      Ok but would it fit on a 17x9 wheel with 5 inch spacing? I don't want to have to use spacers on the rear.
      I don't see why not. But hopefully someone else will chime in that knows for sure. I can only tell you what I have on my car and how it works.

      Andrew
      1970 GTO Version 3.0
      1967 Cougar build
      GM High-Tech Performance feature
      My YouTube Channel Please Subscribe!
      Instagram @dr__efi
      I deliver what EFI promises.
      Remote Holley EFI tuning.
      Please get in touch if I can be of service.

      "You were the gun, your voice was the trigger, your bravery was the barrel, your eyes were the bullets." ~ Her

    16. #16
      Join Date
      Apr 2011
      Location
      North NJ/SW Virginia
      Posts
      197
      Country Flag: United States
      Okay, a quick update:

      Today i got the wheels and I think the look awesome. I pulled a front and back wheel to make sure there would be no rubbing issues and it looks all good. I've ordered Nitto 555's so I'll post pictures of them when they are mounted on the car.

      Name:  photo8.jpg
Views: 9792
Size:  223.1 KBName:  photo(12).jpg
Views: 15769
Size:  185.6 KB
      John McLoughlin
      1970 Pontiac Lemans
      https://www.pro-touring.com/showthre...-Lemans-Update

    17. #17
      Join Date
      Feb 2005
      Location
      Sydney, Australia
      Posts
      1,797
      Country Flag: Australia
      Outstanding....those YO Rally IIs are going to become a Pontiac "classic" wheel choice!
      Regards,
      Leigh

      Sydney, Australia
      1971 Firebird 455

      https://www.pro-touring.com/showthre...Project/page27

    18. #18
      Join Date
      Jan 2008
      Location
      Houston, TX
      Posts
      193
      Country Flag: United States
      Wanna see that with tires on...good looking ride.
      Asa Walker
      Houston, TX

    19. #19
      Join Date
      Apr 2011
      Location
      North NJ/SW Virginia
      Posts
      197
      Country Flag: United States
      Here are so photos of the wheels on the car:Name:  9.jpg
Views: 14955
Size:  263.5 KB

      I can't drive it yet because the wheels studs are too short. The new cast aluminum wheels are a lot thicker, and the lug nut does not get enough engagement. Year One says they will work with stock studs, but I have no faith in them. I'll order new studs and press them in this coming week. The car needs to be lowered around an inch in the front and the back looks about the right height. I know I planned on not spending money on the body until the suspension/brakes were done but that fell through. I went to Carlisle and came home with a new rear bumper (The pictures make i look good but its shot along with the front) and various other chrome bits. I also bought a new front bumper (almost impossible to find) so I had to buy it when I found it. After the wheels studs are sorted out I want to completely gut the front and rear suspension and step up to big brakes and all new control arms etc. That could be a while off because I'm getting low on funds and I don't start work for another month.

      More updates to come.
      John McLoughlin
      1970 Pontiac Lemans
      https://www.pro-touring.com/showthre...-Lemans-Update

    20. #20
      Join Date
      Dec 2005
      Location
      Birmingham, AL
      Posts
      3,355
      Country Flag: United States
      Those look great!
      Stephen

    Page 1 of 6 1 2 3 4 5 6 LastLast



    Advertise on Pro-Touring.com