Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Page 2 of 2 FirstFirst 1 2
    Results 21 to 28 of 28
    1. #21
      Join Date
      Oct 2008
      Location
      Durham,NC
      Posts
      664
      Country Flag: United States
      my hole is near the oil filter and pan has to be removed to drill hole correctly. i will take pics before i drill and after i drill/tap.

    2. #22
      Join Date
      Oct 2004
      Posts
      419
      To clarify, there is a hole in the oil pan rail that you cannot insert a bolt because it is not drilled an tapped in the block?

      I have this pan but I want to make sure its ok before I fire it.

      Every hole in the pan has a bolt in it. I have a genIV iron block.

    3. #23
      Join Date
      Jun 2006
      Location
      NW burbs IL
      Posts
      1,732
      Ok, why would anyone want to add a bolt that the factory did not use? As long as you have a bolt in all the holes supplied by GM then your good to go.
      Matt


      Current project: " Chain Reaction "

      A.K.A. " BIG " by wife, biatch in garage.

      1969 RS Camaro L92 T56 Quadra-link, CW sub, Ford 9" a progressive build.

      Ex track car: 1995 Camaro LS1 T56

    4. #24
      Join Date
      Aug 2007
      Location
      CT
      Posts
      799
      I think I found my leak.

      I never tightened the oil filter when I put the cam in and new the new pan..

      Oh well my bad..

    5. #25
      Join Date
      Nov 2006
      Location
      Mountain Springs, Texas
      Posts
      4,880
      Country Flag: United States
      Quote Originally Posted by Bow Tie 67 View Post
      Ok, why would anyone want to add a bolt that the factory did not use? As long as you have a bolt in all the holes supplied by GM then your good to go.
      I think the reason is that the Autokraft pan flange is thinner and flexes more than the factory pan.

      1969 Camaro - LSA 6L90E AME sub/IRS
      1957 Buick Estate Wagon
      1959 El Camino - Ironworks frame
      1956 Cameo - full C5 suspension/drivetrain
      1959 Apache Fleetside


    6. #26
      Join Date
      Jan 2008
      Location
      Castro Valley, CA
      Posts
      530
      Country Flag: United States
      anyone else need to use washers because the bolts are too long ?
      John S.

      68 "Bloodline" Camaro in assembly...

      Speedtech Sub, Alston G-Billet/Fab 9 rear, Ridetech coil overs, Moser axles, Fesler 19's, Lots of Anvil parts,Twin tubo LS3/T56, Carbon fiber manifold, and the list goes on and on..........

    7. #27
      Join Date
      Jul 2001
      Location
      Detroit, Michigan
      Posts
      6,854
      Country Flag: United States
      Quote Originally Posted by dhutton View Post
      I think the reason is that the Autokraft pan flange is thinner and flexes more than the factory pan.
      That's it exactly.
      1968 Pro-Touring Camaro LS1

      Project: Next Year
      - Start date; June '01
      - Completion; Sometime next year or the year after.....

    8. #28
      Join Date
      Aug 2007
      Location
      CT
      Posts
      799
      Quote Originally Posted by John510 View Post
      anyone else need to use washers because the bolts are too long ?
      Yeah mine were too long but I just used shorter bolts with 1 washer each instead if a stack of washers.
      I thought it looked ghetto.

    Page 2 of 2 FirstFirst 1 2



    Advertise on Pro-Touring.com