Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Results 1 to 6 of 6
    1. #1
      Join Date
      Apr 2005
      Location
      Bonney Lake, WA
      Posts
      135

      wheel modification question

      I have some rear wheels and the offset will not allow me to run 275s. The outer edge of the wheel sits just a bit to far out from the axle. I was thinking of having 1/2" milled off the wheel mounting surface so the wheel will sit in towards the axle. Is this safe to do? will I mess with the integrity of the wheel? Thoughts and or experience here would be appreciated. Jay



    2. #2
      Join Date
      Apr 2001
      Location
      The City of Fountains
      Posts
      16,130
      Country Flag: United States
      Quote Originally Posted by sharp67 View Post
      I have some rear wheels and the offset will not allow me to run 275s. The outer edge of the wheel sits just a bit to far out from the axle. I was thinking of having 1/2" milled off the wheel mounting surface so the wheel will sit in towards the axle. Is this safe to do? will I mess with the integrity of the wheel? Thoughts and or experience here would be appreciated. Jay
      It depends on the wheel, but my gut instinct tells me that this is a bad idea.

      Andrew
      1970 GTO Version 3.0
      1967 Cougar build
      GM High-Tech Performance feature
      My YouTube Channel Please Subscribe!
      Instagram @dr__efi
      I deliver what EFI promises.
      Remote Holley EFI tuning.
      Please get in touch if I can be of service.

      "You were the gun, your voice was the trigger, your bravery was the barrel, your eyes were the bullets." ~ Her

    3. #3
      Join Date
      Aug 2010
      Location
      Seattle area
      Posts
      360
      It is a very bad idea.Either find a wheel with the correct offset .And or flair your fenders. Both are a whole lot safer.than messing with your wheel. Because wheels are built within certain DOT specifications to be able to be on the road.Other wise the wheel could fail and cause a wreck .
      of which could hurt you and or other people.

    4. #4
      Join Date
      Mar 2014
      Location
      Mesa, AZ
      Posts
      637
      Country Flag: United States
      I would not take material off the wheel. Depending on the wheel, if you take 1/2" off the mounting surface you will take away most of the material there and seriously compromise the wheel's structural integrity. This is an accident waiting to happen. Spend the money and get correct sized wheels for the car.
      Nelson
      1969 Chevelle "Cone Smasher" Family Project
      https://www.pro-touring.com/threads/...uot?highlight=

      1984 "Rustang" GT, 5.0, 5 Speed Project
      https://www.pro-touring.com/threads/...T-(Slow-Build)

    5. #5
      Join Date
      Sep 2010
      Location
      Beach Park IL
      Posts
      3,060
      Country Flag: United States
      I have machined wheels to change the offset. There is a standard thickness for aluminum wheels...... .400" maybe......but those were set up for a mag shank lug nut.

      I think you will find that if you milled .500" off of your wheels that there will be no seat left for the lug nut......at that point you have expensive paper weights.
      Donny

      Support your local hot rod shop!

    6. #6
      Join Date
      Feb 2003
      Location
      Houston, TX
      Posts
      3,446
      Country Flag: United States
      Most wheels are designed to accommodate a safe load range, and the lug holes are drilled to a specific depth in order to retain the required material thickness under the lug nuts. If you mill the backside of the wheels, you remove material from a critical area of the wheel. Not recommended. Your other option is to have the rear axle narrowed, or buy wheels that fit properly.

      Tony
      Co-Founder, LS1TECH.com


      Forged Wheel Dealer, Contact me for a quote!
      www.DV8Motoring.com




    Advertise on Pro-Touring.com