Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Results 1 to 10 of 10
    1. #1
      Join Date
      Dec 2002
      Location
      New York
      Posts
      409

      Looking for new DFI Setup

      Starting research on changing my current Accel DFI setup on my Accel / Lingenfetlter Superram kit - running the old Gen Vi. Any recommendations would be appreciated - also to mention that I am running a 4l60E tranny - so if there this anything out there that can run both under one platform - that would be good. I believe that Holley makes something for both.

      Running a pre 86 350 block - with a Accel Small cap HEI distributor.

      Thanks

    2. #2
      Join Date
      Sep 2014
      Location
      Sun City West, AZ
      Posts
      672
      Country Flag: United States
      I am replacing my Accel Gen 7 system with a Holley. The Holley DFI appears to be a better system. The Holley uses a Wideband oxy and is a self learning system with faster corrections. Also, it is my understanding the Holley has a lot of diagnostics so you can look at previous problems. I'm not sure if it has a tranny control feature. Lingenfelter is installing my new Holley system.
      --
      Kenny Mitchell
      [email protected]

    3. #3
      Join Date
      Sep 2004
      Location
      Kettering, OH
      Posts
      537
      I'm interested in knowing how you guys plan to handle the wiring harness changeover/conversion. As Accel discontinued all support for their DFI systems, I feel I need to have a plan for converting my Gen7 to another ecm, but my wiring is completely integrated into the car so I don't want to swap the harness.
      1967 Firebird Convert, Fuel Injected 462 ci, TKO 600
      http://1967firebird.atwebpages.com

    4. #4
      Join Date
      Sep 2014
      Location
      Sun City West, AZ
      Posts
      672
      Country Flag: United States
      I would assume that the wiring harness pinouts are different for each system. I guess you could review the schematics of each system to see if the harnesses are compatible or rearrange the pinouts accordingly if the connectors are compatible. Unfortunately, my new Holley system is back in Michigan at Lingenfelter and I have my old DFI system here at home so I can't compare.
      --
      Kenny Mitchell
      [email protected]

    5. #5
      Join Date
      Sep 2004
      Location
      Kettering, OH
      Posts
      537
      Quote Originally Posted by nokones View Post
      I would assume that the wiring harness pinouts are different for each system. I guess you could review the schematics of each system to see if the harnesses are compatible or rearrange the pinouts accordingly if the connectors are compatible. Unfortunately, my new Holley system is back in Michigan at Lingenfelter and I have my old DFI system here at home so I can't compare.
      Yes, that's what I figured because I cut my Gen7 harness, took out all the unused wires, pulled them to the length needed and reassembled the connector at the ecm: http://1967firebird.atwebpages.com/engine3.php The connector used standard Delphi/Packard pins. So my real question would be, does the Holley unit come with a detailed pin out and does the connector use some type of standard pin? The only problem I had with the Gen7 was that the dualsync distributor used wires of the same color for multiple inputs, making it hard to keep them straight.

      I am also wondering if one could start with the same VE, AF and Timing maps, interpolating if necessary to transpose them to the Holley maps.

      1967 Firebird Convert, Fuel Injected 462 ci, TKO 600
      http://1967firebird.atwebpages.com


    6. #6
      Join Date
      Dec 2008
      Location
      Connecticut
      Posts
      31
      Country Flag: United States
      Quote Originally Posted by Hammered View Post
      So my real question would be, does the Holley unit come with a detailed pin out...
      http://documents.holley.com/techlibr...10555rev17.pdf (Holley EFI Wiring Manual - See Section 13, Wiring Appendix)

      ...and does the connector use some type of standard pin?
      http://forums.holley.com/showthread....als-Holley-EFI (ECU Connectors & Terminals - Holley EFI)

      I'm also wondering if one could start with the same VE, AF and Timing maps, interpolating if necessary to transpose them to the Holley maps.
      Yes, Holley EFI also uses Speed Density two dimensional RPM & kPa tables. VE Based is one of the Load Sensing strategies in Engine Parameters.
      http://documents.holley.com/techlibr...r10632rev5.pdf (V2+ Software/Firmware Overview - See Page 6)
      May God's Grace Bless You

      '78 BRONCO: 508" stroker, TFS heads, Dominator MPFI & DIS, 100HP progressive dry direct-port NOS, A/C, Lentech Strip Terminator wide-ratio AOD, 3:1 Atlas II, modified Dana 44/60-lockers-4.10s, hydroboost/4-disc brakes, ram-assist/heim joint steering, 4" lift, 35" tires

    7. #7
      Join Date
      Sep 2004
      Location
      Kettering, OH
      Posts
      537
      Quote Originally Posted by Danny Cabral View Post
      http://documents.holley.com/techlibr...10555rev17.pdf (Holley EFI Wiring Manual - See Section 13, Wiring Appendix)


      http://forums.holley.com/showthread....als-Holley-EFI (ECU Connectors & Terminals - Holley EFI)


      Yes, Holley EFI also uses Speed Density two dimensional RPM & kPa tables. VE Based is one of the Load Sensing strategies in Engine Parameters.
      http://documents.holley.com/techlibr...r10632rev5.pdf (V2+ Software/Firmware Overview - See Page 6)

      Thank you! This makes a swap look a lot more doable. I found this link that shows how to adapt the Accel Dual Sync distributor to the Holley: http://www.chevytalk.org/fusionbb/sh...hp?tid/266281/
      1967 Firebird Convert, Fuel Injected 462 ci, TKO 600
      http://1967firebird.atwebpages.com

    8. #8
      Join Date
      Dec 2002
      Location
      New York
      Posts
      409
      Thanks for all the great info. I would probably just do a fully wiring harness swap - just to eliminate any potential issues.

    9. #9
      Join Date
      Nov 2012
      Location
      ocala fl
      Posts
      302
      Country Flag: United States
      HOLLY HP controls the transmission. Their wiring harness is easy to use. They make wiring harness for the trans and fly by wire. You have to load it in to the unit with a lap top. It also controls boost and a lot of different things. The Dominator EFI controls more and is more for the serious racer. My only gripe with the wiring is the leads under the hood are too short. The water temp is almost 16' too short if you want to keep the big wiring harness "hid" at the back of the motor.

    10. #10
      Join Date
      Jul 2006
      Posts
      294
      Country Flag: United States
      Quote Originally Posted by chpr1972 View Post
      HOLLY HP controls the transmission. Their wiring harness is easy to use. They make wiring harness for the trans and fly by wire. You have to load it in to the unit with a lap top. It also controls boost and a lot of different things. The Dominator EFI controls more and is more for the serious racer. My only gripe with the wiring is the leads under the hood are too short. The water temp is almost 16' too short if you want to keep the big wiring harness "hid" at the back of the motor.
      Holley HP does not control transmission.
      Tom




    Advertise on Pro-Touring.com