Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Results 1 to 18 of 18
    1. #1
      Join Date
      May 2009
      Location
      Houston
      Posts
      149

      brake bias question

      I just did a rear disc brake conversion on the ol 87 silverado as seen on this thread:
      https://www.pro-touring.com/forum/sh...ad.php?t=66403
      and was wondering if I should gut the prop vale, modify it somehow, or gut and install a adjustable prop valve for the rear.

      A quick search shows GM D-52 pistons are 2.80"
      An alldata chart shows the Dodge Ram piston to be 2.12"
      total of 4.92"
      front 2.80/4.92= 56%
      rear 2.12/4.92= 44%

      Not quite a natural 70/30 split. Currently with stock fronts will start to screatch before they lock up (when at a real low speed) before the rears when the pedal is mashed and held. The fronts have got to be glazed becuase I did a very hard stop... could smell the pads once I pulled back into the shop. Right now I have no complaints about stopping becuase it feels great having 4 wheel brakes.

      So what are your recommendations to the brake bias?
      Leave it -or- Change it
      Thanks,
      clint

    2. #2
      Join Date
      Apr 2001
      Location
      Central CA USA
      Posts
      6,114
      Country Flag: United States
      Don't compare bore diameters, compare bore area in square inches. Compare a single piston to multi-piston caliper by only using one side of the multi-piston caliper area in sq inches.
      Rotor diameter matters too as well as tire height.
      David
      67 Camaro RS that will be faster than anything Mary owns.

    3. #3
      Join Date
      May 2005
      Location
      Fontana, CA
      Posts
      4,960
      Country Flag: United States
      For me, once you leave the factory settings/setup, an adjustable prop is mandatory. A lot of R&D went into setting the factory prop valve/bias properly. Simply gutting the factoert valve doesn't ensure good results. Get an adjustabple prop, and then go test to ensure it works properly. I start with a lot of rear pressure. Get up to ~40 and jam the brakes. If the rears lock up, back out pressure and try it again. Continue @ 40 (making very small adjustments) until the rear lockup goes away. Once gone, repeatedly. Perform the test @ 50, then 60, then 70. If consistent, you should be dialed in well.
      Nick R.
      69 Camaro - 383, 700R4, 12 bolt 3.55, Hotchkis, Bilstein, Global West, Morris Classic
      08 HHR SS - Still Stock for now
      Do you still believe in all the things that you stood by before? Are you out there on the front lines, or at home keeping score?
      Do you care to be the layer of the bricks that seal your fate? Would you rather be the architect of what we might create?

    4. #4
      Join Date
      May 2009
      Location
      Houston
      Posts
      149
      does anyone perfer any brand of prop valve over another. Im sure they are just about the same just different brand.
      thanks for the replys,
      clint

    5. #5
      Join Date
      May 2005
      Location
      Fontana, CA
      Posts
      4,960
      Country Flag: United States
      Wilwood has a slick new distribution block/adj. prop valve. I use Wilwood everything already.
      http://wilwood.com/MasterCylinders/M...derValves.aspx
      Nick R.
      69 Camaro - 383, 700R4, 12 bolt 3.55, Hotchkis, Bilstein, Global West, Morris Classic
      08 HHR SS - Still Stock for now
      Do you still believe in all the things that you stood by before? Are you out there on the front lines, or at home keeping score?
      Do you care to be the layer of the bricks that seal your fate? Would you rather be the architect of what we might create?

    6. #6
      Join Date
      Aug 2008
      Location
      Pgh, PA
      Posts
      2,177
      That's a nice valve. I like that it splits your front right at the valve as well as allowing bias adjustment. Too late for me, but it's cool.

    7. #7
      Join Date
      Apr 2009
      Location
      san diego
      Posts
      5,101
      Country Flag: United States
      I have my proportioning valve adjustable from the drivers seat. I use the wilwood, I have no issues.



    8. #8
      Join Date
      Jun 2007
      Location
      Greenwood, SC
      Posts
      1,611
      Country Flag: United States
      Quote Originally Posted by falcon65 View Post
      I have my proportioning valve adjustable from the drivers seat. I use the wilwood, I have no issues.
      Bryce, got pics of this? I'd be interested to see your control ergonomics....
      JC Scott


    9. #9
      Join Date
      Apr 2009
      Location
      san diego
      Posts
      5,101
      Country Flag: United States
      let me look through my pics and see what I can find. I am here at work right now.

    10. #10
      Join Date
      Apr 2009
      Location
      san diego
      Posts
      5,101
      Country Flag: United States


      it sits through the floor right next to the front left seat mount. kinda hard to see in this picture. best I have right now.

    11. #11
      Join Date
      Oct 2004
      Posts
      2,624
      Country Flag: United States
      Make sure the wife doesn't mistake it for the lumbar adjustment!
      Red Forman: "The Mustang's front end is problematic; get yourself a Firebird."

    12. #12
      Join Date
      Jun 2007
      Location
      Greenwood, SC
      Posts
      1,611
      Country Flag: United States
      In the floor beside the rocker? Thats cool. I was trying to think of a good place to mount one. I was thinking near the trans tunnel would be easier/quicker access, but packaging may be a little difficult....

      I really like your door panels too.... Did you do them? They look really simple and clean.
      JC Scott


    13. #13
      Join Date
      Apr 2009
      Location
      san diego
      Posts
      5,101
      Country Flag: United States
      HAHA, lumbar. support!!! actually I have that built into the seat its on the passenger side of the driver seat. you can see the grommet in the side of the seat.

      Per NHRA rules, the brake lines can not be run down the drive shaft tunnel. the must be on the outside of the frame rails. That is the reason for the proportioner in that location.

      Yep i made the door panels. My next set will be all aluminum with tweed inserts. For more questions about my car not "brake bias" subject please ask in my thread, see my signature. i dont want to hijack the OP thread.

    14. #14
      Join Date
      Aug 2004
      Location
      Rustburg, Virginia
      Posts
      3,436
      Country Flag: United States
      I have mine mounted just ahead of the driver's seat. I might re-do mine because I like the way Bryce's is set up.....I have brake lines under my driver's seat and it could rub a hole in the line where they go through the floor(even though I have rubber grommets)
      1970 RS/SS350 139K on the clock:
      89 TPI motor w/ 1pc rear seal coupled to a Viper T56 via Mcleod's modular bellhousing w/ hydraulic T/O bearing from the Viper, 12 bolt rear w/ 3.73 gearing, SC&C upper control arms, factory lowers with Delalums, C5 brakes at all four corners, Front Wheels 17x8's with Sumi 255/40/17 and Rear Wheels 17x9's with Sumi 275/40/17.
      Brief description of the work done so far can be found here: http://www.nastyz28.com/forum/showthread.php?t=112454


    15. #15
      Join Date
      Apr 2009
      Location
      san diego
      Posts
      5,101
      Country Flag: United States
      My brake lines remain under the car. Just the handle of the PV pokes through the floor. And I can still reach if I had a 5 point harness on.

    16. #16
      Join Date
      Jun 2007
      Location
      Greenwood, SC
      Posts
      1,611
      Country Flag: United States
      Quote Originally Posted by falcon65 View Post
      Per NHRA rules, the brake lines can not be run down the drive shaft tunnel. the must be on the outside of the frame rails. That is the reason for the proportioner in that location.
      Interesting..... do these same rules apply to NASA (or equivalent)?

      Ever run across a remotely mounted prop valve controller?

      I'm just thinking out loud....
      JC Scott


    17. #17
      Join Date
      Apr 2009
      Location
      san diego
      Posts
      5,101
      Country Flag: United States
      yes, wilwood makes a cable drive handle for their proportioner. Im not sure if NASA has that rule. but it makes sense. If you have a u-joint failure or break a driveshaft you dont want it taking out your brakelines.

    18. #18
      Join Date
      Aug 2004
      Location
      Rustburg, Virginia
      Posts
      3,436
      Country Flag: United States
      The M/C is on the driver's side...so it makes sense that the rear brake line travels down that side of the car anyway....my camaro rear brake line runs along the driver's rocker so it was a piece of cake to plumb in the prop valve right there.
      1970 RS/SS350 139K on the clock:
      89 TPI motor w/ 1pc rear seal coupled to a Viper T56 via Mcleod's modular bellhousing w/ hydraulic T/O bearing from the Viper, 12 bolt rear w/ 3.73 gearing, SC&C upper control arms, factory lowers with Delalums, C5 brakes at all four corners, Front Wheels 17x8's with Sumi 255/40/17 and Rear Wheels 17x9's with Sumi 275/40/17.
      Brief description of the work done so far can be found here: http://www.nastyz28.com/forum/showthread.php?t=112454





    Advertise on Pro-Touring.com