Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Page 2 of 3 FirstFirst 1 2 3 LastLast
    Results 21 to 40 of 43
    1. #21
      Join Date
      Apr 2005
      Location
      Cartersville, GA
      Posts
      1,298
      Country Flag: United States
      Quote Originally Posted by WS6
      Yeah, that would be pretty sweet. I'm probably going to adapt a 94-95 harness, and have my PCM reflashed by PCMsforless for the time being. Once the car is up and running, I'll have Brad Brand tweak it a bit if needed (if he's still around...last I heard he was in Covington?).
      Joe Hinds

    2. #22
      Join Date
      Aug 2004
      Location
      Dunwoody, GA
      Posts
      4,983
      Country Flag: United States
      Yes, Brad is in Covington. I was just at his shop last week doing some pulls with a C6.

      Good luck with the engagement too. The car can wait for life to happen first.
      Trey

      "The early bird may get the worm, but the second mouse gets the cheese."
      ~ Jon Hammond

      1979 WS6 Trans Am stock LT1/T56 drive train out of my Formula. BMW M-parallel rims. C5/C6 brakes

      build thread https://www.pro-touring.com/showthre...ghlight=begins

    3. #23
      Join Date
      Dec 2004
      Location
      charleston, SC
      Posts
      853
      Country Flag: United States
      Good choice on the '81. My dad had an '81 and I like them better with the spoiler unlike the previous years.

      "Dad, I can't see over the nose."

      "Don't worry. Just point and go"
      Robert's 1969 Camaro - 2002 LS1/T56, 10pt cage, Global West Stage III front suspension, HTH truck arm rear suspension, Sprint Cup 9" full-floating rear end, Fikse Mach V 17" up front 18" in the back and still working on it...

    4. #24
      Join Date
      Apr 2005
      Location
      Cartersville, GA
      Posts
      1,298
      Country Flag: United States
      Wow, I have gotten way behind on this thread! Life has gotten in the way, but I am finally making some more progress on the car. I'll post some updates and pics later.
      Joe Hinds

    5. #25
      Join Date
      Nov 2008
      Location
      Iceland
      Posts
      896
      Country Flag: Iceland

    6. #26
      Join Date
      Nov 2008
      Location
      iceland
      Posts
      1,859
      Country Flag: Iceland

    7. #27
      Join Date
      Aug 2004
      Location
      Dunwoody, GA
      Posts
      4,983
      Country Flag: United States
      Great to know you're still out there Joe. Hey, I found a new shop that has an in ground dynojet. The company is red star performance. They are in Oxford which is just north of Convington. www.redstarperformance.com

      Very small shop but they seem to be getting a good reputation.
      Trey

      "The early bird may get the worm, but the second mouse gets the cheese."
      ~ Jon Hammond

      1979 WS6 Trans Am stock LT1/T56 drive train out of my Formula. BMW M-parallel rims. C5/C6 brakes

      build thread https://www.pro-touring.com/showthre...ghlight=begins

    8. #28
      Join Date
      Apr 2005
      Location
      Cartersville, GA
      Posts
      1,298
      Country Flag: United States
      Wow, eleven months since the last post! A lot has changed since my last post; the Camaro SS that was going to be the donor was sold (with the 383), I did get engaged, and I am now self-employed, building cars (I used to be a stockbroker!) and doing performance and general repair work. I'll be opening a shop sometime after the first of the year (still looking for a suitable location).

      I have made a few changes in my plan for the build, however. I'm going with an iron block 6.0 stroker, with L76 heads and an Edelbrock Victor single plane. I'll use a 4 barrel-style throttle body. The T56 willl remain, but I do have some different plans for the rearend. I had originally planned to do the early C3 iron diff on the original batwing, but since my new power plans may be a little much for that, and a Tom's 12 bolt is a little too much, I'm adapting another IRS centersection to the car. I have two different ideas on that, one being fairly cheap and simple (8.8 Ford IRS), the other...well. a little more complex and expensive, but definitely bulletproof. More on that when I get to that stage,

      I'll post more pics as soon as I can get them uploaded, but for a quick update I have done the following since the last post: removed both doors, removed the interior, removed the engine/trans, welded in new floorpans, stripped the rest of the paint from the main body, and removed the front clip.
      Joe Hinds

    9. #29
      Join Date
      Apr 2005
      Location
      Cartersville, GA
      Posts
      1,298
      Country Flag: United States
      Ok, I'll start with the underhood area. The engine and trans were pulled as a unit, and sold($650). It still ran well, for a basically stock engine, but was far from what I want for this car. As you can see, its pretty grungy under the hood, but its in decent shape otherwise. The front clip will be coming off soon; its not damaged too badly (repairable), but there is some surface rust in the corners under the windshield frame area of the birdcage, and the only way to fix it right is to get the clip out of the way.







      Joe Hinds

    10. #30
      Join Date
      Apr 2005
      Location
      Cartersville, GA
      Posts
      1,298
      Country Flag: United States
      I got a bit ahead of myself while cutting out and replacing the passenger side floorpan, and didn't get any before or progress pics, but I will take plenty when I do the other side. Here is the driver's side, after rust treatment. I wasn't happy with it, so its being cut out next.

      Joe Hinds

    11. #31
      Join Date
      Apr 2005
      Location
      Cartersville, GA
      Posts
      1,298
      Country Flag: United States
      When doing any kind of sheetmetal work, one of the hardest parts is holding the panel in the correct position while you begin tacking it in place. The solution to this dilemma is a simple spring loaded, removable, rivet-like device called a Cleco. Originally developed for aircraft construction, they work great for any sheetmetal project. Just drill a hole through the overlapping panels (either 1/8 or 3/16, they are sold in both sizes), insert the Cleco into the Cleco pliers, and squeeze to extend the spring loaded tip. Insert the Cleco into the hole, and release the pliers, and the tip expands to hold the panels in place. Summit sells a kit, SUM-G1850, that includes the pliers and 10 1/8 and 15 3/16 pins, for $17.95. Extra pins in 1/8 are SUM-G1852; 3/16 are SUM-G1853. Each is $12.95 for a pack of 20.

      Joe Hinds

    12. #32
      Join Date
      Apr 2005
      Location
      Cartersville, GA
      Posts
      1,298
      Country Flag: United States
      Here are a few shots of the nearly-finished passenger side panel. Welding was done with a 115v MillerMatic mig welder, using straight Co2 as a shielding gas. The welder belongs to my dad, and has been used to put in countless body panels on probably a dozen different cars. He has had it for about 18 years, with no issues, ever.

      If you haven't done a lot of welding, don't be intimidated...its fairly easy to get functional welds (pretty ones are a bit tougher, and aren't always "good" welds" ). For sheetmetal, on this particular welder, I set the voltage to 1 (the lowest setting), and the wire speed is on 10. This varies according to the thickness of the steel, and the welder itself, so don't be afraid to experiment. The main thing to consider when using a MIG welder (or any type of arc welder), is proper clothing and eye protection. It is very easy to burn your eyes with a welder, and its a painful experience. You don't necessarily feel it at first, but after a few hours your eyes hurt and you will be streaming tears for the next several hours. Ask me how I know, though it has been several years since this was an issue. I use an auto-darkening helmet to prevent this:

      Always weld in a very well lit area (halogen floodlights work well), since even with the autodarkening helmet it can be tough to see what you are doing sometimes. You have probably seen people weld using the "look away" method, and while I am guilty of using it myself sometimes, its not advised. Keep in mind as well that you can easily get sunburned if you don't cover up adequately. Welding coats and gloves are the best way to avoid this, but most of the time long sleeves and gloves of some sort (I use a pair of old Mechanix Wear Extreme gloves for just about everything) are a mimimum requirement. Heavy gloves of some sort are needed when handling sheetmetal anyway, whether new or the old rusty stuff. Nothing can slice you open faster than a piece of sheetmetal.
      Of course, you need eye protection when cutting or grinding as well. I have had metal cut from my eye twice, and both times I was wearing safety goggles. For best protectionl, I now use a full face shield.

      The pan is overlapped at the rear and along the rocker, like factory. I drilled holes for the Clecos, and welded them up as I went along, to duplicate the factory spot welds. I am also welding the seam (not finished in these pics) for extra strength. I also used the Clecos to butt weld the pan to the tunnel. How, you say? I made a sheetmetal "bridge", just a steel scrap with 2 holes in it, to hold the panels close together so that they could be butted together.




      Joe Hinds

    13. #33
      Join Date
      Apr 2005
      Location
      Cartersville, GA
      Posts
      1,298
      Country Flag: United States
      Here are a few of the tools that I used to get the old floorpan out. There are many different ways to do this. The grinder at the top left is a 4" Makita. You can get grinding or cutting discs for it. At the top right is my Ryobi 18v corless drill; middle left is a Ingersoll Rand angled die grinder (equipped with a cut off wheel currently). The IR grinder is what I use for more detailed cutting, though an air powered body saw will do the same thing. To its right is a Campbell Hausfield air chisel. I use that to do the rough cuts, and to seperate panels at the seam.
      Some people prefer a spot weld cutter for that (drill out the spot welds and the panel comes loose), but I didn't use mine because I was having difficulty seeing the spotwelds. A hammer and a pry bar or two are also handy. I have body hammers, but the weight of this hammer was better suited for the thicker sheetmetal of the floorpan.

      Here are the two most commonly used bits for the air chisel. The one on the left is for cutting panels...notice the upturned tip in the center. The one on the right is a flat blade, which is best for seperating panels.


      I'll start with a pic of the new drivers' side floorpan. This one came from an Ebay vendor, and was about $250 plus shipping.

      Notice the left side of the panel goes up, and welds directly to the rocker panel. While this is great if you have a lot of rust on that side, its not completely correct. The factory panel is flat on the left (outer) side, and overlaps a seperate piece that comes down from the rocker. If you are concerned about it looking 100% as the factory did it, you will have to cut the angled part off and overlap the piece coming off of the rocker. This is probably the easiest way to do it, but I chose not to, for a couple of reasons. One, I felt that the factory metal had been weakened substantially by all that flaky rust. Two, I suspected there may be rust on the rocker area of the birdcage (under the fiberglass skin).As far as the sheetmetal itself is concerned, welding in either way is about the same level of difficulty. If you do it the factory way, you don't have to remove any fiberglass. This would be preferable in a car that has good paint, but needs a floorpan. My way has the downside that the fiberglass rocker cover has to be removed, but since I am doing bodywork and repainting the car it isn't a concern. I just wanted to make sure I got all of the rust. I plan on keeping this car forever, for sentimental reasons, and don't want to have to do any of this kind of thing over again.
      Joe Hinds

    14. #34
      Join Date
      Apr 2005
      Location
      Cartersville, GA
      Posts
      1,298
      Country Flag: United States
      Here I am making the initial cuts on the drivers's side floorpan. Using the metal cutting blade for the air chisel, I started on one of the seat belt mounting holes and essentially cut until I had removed most of the horizontal surfaces. I always rough cut the panel out, much smaller than the new panel, to make sure I don't cut off too much.

      Here you can see most of the panel cut out. At the front, it is riveted to the fiberglass toeboard so you don't want to get too crazy with the air chisel.

      Here I am drilling out the rivets at the front. They are very soft, and come out easily.

      The panel is rough cut out. Notice you can see the lip on the left side where the 2 panels are joined, as I mentioned above. The remainder there will be removed from the birdcage/rocker, but some fiberglass has to be removed first.

      The rear of the panel, as I mentioned earlier, could be removed by drilling out the spot welds. I was having trouble seeing them, so I used the flat blade on the air chisel to seperate the panels. Be careful if you use this method, as its easy to tear up the flange. I thought I had a picture of this process, but I guess not.
      To remove the rocker flange, you have to get the fiberglass rocker cover out of the way. In my case, the carpet was already removed by the previous owner. He left the sill plate, so I removed those first:

      Next, I drilled out the rivets holding the rocker cover down.

      The fiberglass piece at the front of the doorjamb needs to be removed as well, since it overlaps this panel. Start by drilling out the rivets, then cut at the seam where it joins the rocker piece. I did this with a small chisel, as there were tons of seam sealer or adhesive of some type holding it in place. It may take a little working back and forth with a small flat scraper to break the bonds, and get this piece loose. A little heat from a heat gun, or judcious use of a small propane torch will wrok wonders on the old adhesive.There will probably be some damage at the bottom, but this can be fixed easily enough later.Just be as careful as you can here.

      Here I am using the cutoff wheel to cut the rocker panel cap loose from the rear doorjamb/quarter.

      Once the rocker cover is loose, you can carefully pull it out. As I suspected, I found some fairly heavy surface rust underneath. The rocker itself was still very solid, thankfully, so other than cleaning and rustproofing it won't require any further repair.

      The rocker/birdcage underneath...lots of flaky rust, as I suspected.

      The front doorjamb area. There is some rust here, too. You'll have to remove quite a bit of seam sealer to really get this area clean. The door hinge shims will likely be stuck to the jamb, so this is a good time to carefully remove them and bag and tag them so you will know where they came from when you are putting the car back together. In this case, the whole front clip is coming off, because I suspect there may be more hidden rust that can only be properly repaired with the clip out of the way.

      Speaking of seam sealer, there will be some on the front flange of the toeboard. If its dry and flaky, you may be able to get it off just using a scraper. I heated mine a bit, since it was still kind of tarlike.
      Joe Hinds

    15. #35
      Join Date
      Apr 2005
      Location
      Cartersville, GA
      Posts
      1,298
      Country Flag: United States
      Here I am seperating the remnant of the floorpan from the rocker/birdcage. I used the flat blade for this, and once the panel was removed I cleaned up the edge with the grinder. This will take care of any metal left by the spot welding. After this was done, I ground the top and outer side surfaces of the rocker with the 4"grinder, then used a wire brush on a die grinder to remove the rest of the rust. After a tip I heard recently, I wiped the rocker down with common household distilled white vinegar and it eliminated the rest of the rust. I noticed it smells just like Metalprep. Once all the metal work is done, everything will be coated with Rust Bullet (similar to POR-15), and all seams will be seam sealed.

      After a little more trimming on the tunnel side with the cutoff wheel, I dropped the floorpan in place and carefully positioned it. It may need to be tweaked slightly here and there with a pry bar and hammer, especially at the rear. Once I was satisfied with the position, I started drilling holes and installing the Clecos to hold it in place.

      Here are a few more installed. If you are doing a resto and want it to be exact, put the Clecos where the original spot welds were, so that when you spot the pan back in place it will be identical to the way it was originally. Since I am not concerned with this, I placed the Clecos where I thought they were needed to hold the panel best. Spacing isn't even, and I didn't intend for it to be.

      Here is a view from above the rocker, with more Clecos in place. They will eventually be placed all along the back, as well as down the rocker. I bolt the floorpan to the toeboard as a temporary measure, since Clecos don't work well on fiberglass. I save the tunnel for last. Notice that the edge of the floorpan is higher than the rocker. Once the panel is spotted in (via the Cleco holes), I will use the 4" grinder to grind the panel flush to the rocker. After that, I will hammer the edge to get the gap as tight as possible, then start making short stitch welds to avoid warpage to the panel. Eventually it will be welded solid, both here and at the rear of the panel. I anticipate a little extra stiffness will be the result, though I don't know if it will make a measurable difference. Every little bit helps.
      Joe Hinds

    16. #36
      Join Date
      Apr 2005
      Location
      Cartersville, GA
      Posts
      1,298
      Country Flag: United States
      I apparently didn't take any more pics of the floorpan as it was going in; here are a few of the finished product (the front of the pans still needs to be rivited to the toeboards). It is coated with Rust Bullet. I used 3M Seam Sealer (in a tube) to seal the seams.





      Joe Hinds

    17. #37
      Join Date
      Apr 2005
      Location
      Cartersville, GA
      Posts
      1,298
      Country Flag: United States
      Here it is with the front clip removed. How do you remove the front clip on a Corvette? With great difficulty! With patience, you can use a heat gun or propane torch (CAREFULLY), along with a long putty knife or (!) kitchen knife to break the bonds. There are no bolts, only very strong adhesive.







      There was some damage on the front clip: at the firewall


      Minor damage on the drivers side rear:



      A little damage on the bonding strip on the passenger side:

      Joe Hinds

    18. #38
      Join Date
      Aug 2004
      Location
      Dunwoody, GA
      Posts
      4,983
      Country Flag: United States
      Looks good Joe. You're doing fine work to that 81. Most people would toss it aside which is a shame. I think they can look great. Keep it up and good luck with the business.
      Trey

      "The early bird may get the worm, but the second mouse gets the cheese."
      ~ Jon Hammond

      1979 WS6 Trans Am stock LT1/T56 drive train out of my Formula. BMW M-parallel rims. C5/C6 brakes

      build thread https://www.pro-touring.com/showthre...ghlight=begins

    19. #39
      Join Date
      Oct 2006
      Location
      Morristown, NJ
      Posts
      154
      Good work so far. I have always had a soft spot for the 81 Vettes. My dad had one growing up. I took my driving test in it.
      1973 Camaro Type LT/RS
      http://www.apiem.com/camaro

    20. #40
      Join Date
      Apr 2005
      Location
      dayton, oh
      Posts
      952
      nice work, nice job documenting it. I have pretty much all the same tools, doing the same job to my 442. fun, isn't it?

      dave.t
      86 Olds 442 - Project If It Ain't Broke, Take It Apart and Fix It
      74 Javelin AMX - stocker


    Page 2 of 3 FirstFirst 1 2 3 LastLast



    Advertise on Pro-Touring.com