Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Page 2 of 6 FirstFirst 1 2 3 4 5 6 LastLast
    Results 21 to 40 of 114
    1. #21
      Join Date
      Aug 2004
      Location
      Walla Walla, WA
      Posts
      1,512
      Country Flag: United States
      Quote Originally Posted by Taylor1969 View Post
      Looks like my list may be as follows then:


      I need to purchase the following:
      The Gear Box LS1 T56 to SBC adapter Plate - $190
      The Gear Box Extended Pilot Bushing - $25
      Crossmember - RaptorX - $200
      RodLinks Clutch Linkage for '67-'69 Camaro - $60
      Sachs Clutch Kit - $200
      GM Steel Flywheel - $100

      Grand total - $775
      I've done the dance with the Raptor crossmember. They created the pattern for their crossmember using an LT1 transmission and bellhousing, which puts the transmission mounting point roughly 2" closer to the engine than does the LS1 T56 and adapter plate mounting. In order for their crossmember to work with the LS1 T56, you'll need to get that 2" back by redrilling the crossmember mounting pad and/or redrilling your subframe. I concluded that was going to be difficult. Check with them to see if that's still the case.

      If it is, the ATS crossmember will definitely work. For my conversion (and being more optimistic on timing than was warranted and believing that the ATS crossmember wasn't going to be available until after I needed it), I gambled on the BRP crossmember, but haven't installed it yet, so can't say it's easily done.

      Don't forget the other items you'll need if you don't already have them, as listed above.
      Mike Kelcy - '68 Camaro with some stuff done to it.

    2. #22
      Join Date
      Jan 2006
      Location
      Houston, Tx
      Posts
      1,004
      Country Flag: United States
      Quote Originally Posted by Mkelcy View Post
      I've done the dance with the Raptor crossmember. They created the pattern for their crossmember using an LT1 transmission and bellhousing, which puts the transmission mounting point roughly 2" closer to the engine than does the LS1 T56 and adapter plate mounting. In order for their crossmember to work with the LS1 T56, you'll need to get that 2" back by redrilling the crossmember mounting pad and/or redrilling your subframe. I concluded that was going to be difficult. Check with them to see if that's still the case.

      If it is, the ATS crossmember will definitely work. For my conversion (and being more optimistic on timing than was warranted and believing that the ATS crossmember wasn't going to be available until after I needed it), I gambled on the BRP crossmember, but haven't installed it yet, so can't say it's easily done.

      Don't forget the other items you'll need if you don't already have them, as listed above.
      Good info!

      I switched to the raptor because the ATS one doesn't look to be available. Please let me know how you come out on the BMR one because that looks like a nice option too (sure seems to allow a lot of room for exhaust)

    3. #23
      Join Date
      Jun 2009
      Location
      Decatur, AL
      Posts
      130
      Quote Originally Posted by Mkelcy View Post
      In order for their crossmember to work with the LS1 T56, you'll need to get that 2" back by redrilling the crossmember mounting pad and/or redrilling your subframe. I concluded that was going to be difficult.
      I've seen an adjustable transmission mount that allows you to move the mount forward or backwards 4 inches iirc. I have the link at home and will post it later tonight if interested.

      Quote Originally Posted by Mkelcy View Post
      You'll need:
      • McLeod LS1 T56 to SBC adapter Plate (8207) - Make sure it includes the extended pilot bushing and bearing retainer on which the throwout bearing rides.

      I was looking at a RM-6023 Bellhousing/Scattershield from Quicktime Inc. for my application which is very similar to this setup. Do you know anything about it? I'm told it's supposed to hook up sbc Gen I engines to LS styled T-56's without any modifications. It compensates for the .4 inch extra length on the input shaft.

      Quote Originally Posted by Taylor1969 View Post
      I switched to the raptor because the ATS one doesn't look to be available. Please let me know how you come out on the BMR one because that looks like a nice option too (sure seems to allow a lot of room for exhaust)
      I saw that too a couple of days ago too. I found a guy that will fab one up for 125 bucks but I will get that last towards the end of my build.
      2001 Camaro Z28 (DD)
      LS3 525hp GM crate engine, built 4L60e
      1974 Camaro Z28 Type LT
      Solid roller 355 sbc with T-56

    4. #24
      Join Date
      Jun 2009
      Location
      Decatur, AL
      Posts
      130
      I just saw this crossmember over at Bowtie Overdrives for a 1st Gen Camaro for 175.

      This is the adjustable crossmember mount that I was talking about.

      Not sure if the crossmember mount will work with a T-56 as they only say "some manual" transmissions.
      2001 Camaro Z28 (DD)
      LS3 525hp GM crate engine, built 4L60e
      1974 Camaro Z28 Type LT
      Solid roller 355 sbc with T-56

    5. #25
      Join Date
      Jun 2009
      Location
      Decatur, AL
      Posts
      130
      Hey, I emailed bowtie overdrives with this question:

      Hey, I'm moving from a TH400 to a T56 and I just wanted to know if the adjustable transmission mount (part number slidemount) would allow me to use my stock crossmember and mount up the T56 with correct driveshaft phasing.

      Thanks!

      Jason


      Their reply was:


      Yes we use our 2004r/th400 crossmembers with the adjustable mounts to work with the t56's and they have been working out.
      So that maybe a viable and cheaper option. My only concern would be the strength of the adjustable mount.


      According to TCI's page the distance to the mounting pad from the front of the bellhousing on a th400 is 26.94 to 27.66 depending on what tailshaft it has. From the bellhousing to the mounting pad on a T-56 is 26.6 inches so they're only about an inch or so in theory. The 2.5 inches travel both forward and backwards should cover this distance easily.
      2001 Camaro Z28 (DD)
      LS3 525hp GM crate engine, built 4L60e
      1974 Camaro Z28 Type LT
      Solid roller 355 sbc with T-56

    6. #26
      Join Date
      Jan 2006
      Location
      Houston, Tx
      Posts
      1,004
      Country Flag: United States
      Quote Originally Posted by kyphur View Post
      Hey, I emailed bowtie overdrives with this question:



      Their reply was:


      So that maybe a viable and cheaper option. My only concern would be the strength of the adjustable mount.

      According to TCI's page the distance to the mounting pad from the front of the bellhousing on a th400 is 26.94 to 27.66 depending on what tailshaft it has. From the bellhousing to the mounting pad on a T-56 is 26.6 inches so they're only about an inch or so in theory. The 2.5 inches travel both forward and backwards should cover this distance easily.
      interesting...

      I spoke with Mcleod and got some new interesting news as well.... I will post up in the morning. Allows the use of the stock ls1 bellhousing and hydraulics with a conventional clutch and flywheel


    7. #27
      Join Date
      Jun 2009
      Location
      Decatur, AL
      Posts
      130
      That's cool. I'd like to hear what that is but I'm pretty much committed to the Quicktime Bellhousing so far.
      2001 Camaro Z28 (DD)
      LS3 525hp GM crate engine, built 4L60e
      1974 Camaro Z28 Type LT
      Solid roller 355 sbc with T-56

    8. #28
      Join Date
      Jan 2006
      Location
      Houston, Tx
      Posts
      1,004
      Country Flag: United States
      Here is my info on the solution using the stock LS1 bellhousing and hydraulics

      Specialty Parts Required:
      Spacer - Mcleod 8703-12
      Dowel Pins - Mcleod 8707-22
      Clutch Master Cylinder Bracket - Detroit Speed 070424

      Factory Parts (Can be swapped to your liking):
      Standard 153 Tooth Flywheel - Mcleod 460300
      Standard 10.5 in Clutch/Pressure Plate - Mcleod 360703/260170

      You would use the LS1 Stock Hydraulics to make everything work.

      Total cost would be somewhere around $900

    9. #29
      Join Date
      Apr 2005
      Location
      Erie, PA
      Posts
      349
      Country Flag: United States
      I assume you have the shift stick and knob available already? What about a shift boot? Look at the prices for Hurst & Lokar stuff and you will be surprised...

      http://www.popularhotrodding.com/hot...nte_carlo.html
      Andreas
      President First Gen Monte Carlo Club
      www.fgmcc.com

    10. #30
      Join Date
      Jun 2009
      Location
      Decatur, AL
      Posts
      130
      The spacer that you have listed "Spacer - Mcleod 8703-12", isn't that just an adapter plate for their modular bellhousing? Don't you already need the bellhousing?
      2001 Camaro Z28 (DD)
      LS3 525hp GM crate engine, built 4L60e
      1974 Camaro Z28 Type LT
      Solid roller 355 sbc with T-56

    11. #31
      Join Date
      Jan 2006
      Location
      Houston, Tx
      Posts
      1,004
      Country Flag: United States
      Quote Originally Posted by kyphur View Post
      The spacer that you have listed "Spacer - Mcleod 8703-12", isn't that just an adapter plate for their modular bellhousing? Don't you already need the bellhousing?
      according to the tech who developed it at Mcleod said that their modular bellhousing is unnecessary.

    12. #32
      Join Date
      Aug 2004
      Location
      Walla Walla, WA
      Posts
      1,512
      Country Flag: United States
      Quote Originally Posted by Taylor1969 View Post
      according to the tech who developed it at Mcleod said that their modular bellhousing is unnecessary.
      That sounds right. The 8703-12 a "scalloped" spacer ring 0.5" thick, with a clutch fork hole at 9 o'clock.

      The base modular bellhousing (which I would still recommend) is virtually the same depth as the stock LS1 bellhousing at about 5.5". The McLeod site says you need their modular bellhousing (you're substituting an LS1 bellhousing) and the 8703-12 spacer to put an LS1 T56 behind a traditional SBC/BBC.

      The McLeod modular bellhousing application chart is pretty informative: http://www.mcleodind.com/application...L_HOUSING.html

      Before I jumped on the stock hydraulic linkage train, I'd do some reading on the "drill mod."
      Mike Kelcy - '68 Camaro with some stuff done to it.

    13. #33
      Join Date
      Jun 2009
      Location
      Decatur, AL
      Posts
      130
      Did you suggest researching the drill mod because you wanted us to do it beforehand or because you don't like hydraulic setups?

      I found this link to how to do it. But I also read a couple of people saying the 1/8th drill bit is too big and go down one size to a 7/64th's.
      2001 Camaro Z28 (DD)
      LS3 525hp GM crate engine, built 4L60e
      1974 Camaro Z28 Type LT
      Solid roller 355 sbc with T-56

    14. #34
      Join Date
      Aug 2004
      Location
      Walla Walla, WA
      Posts
      1,512
      Country Flag: United States
      Quote Originally Posted by kyphur View Post
      Did you suggest researching the drill mod because you wanted us to do it beforehand or because you don't like hydraulic setups?
      Both actually.
      Mike Kelcy - '68 Camaro with some stuff done to it.

    15. #35
      Join Date
      Jun 2009
      Location
      Decatur, AL
      Posts
      130
      Yeah, now I think reading about how you liked the "feel" of the mechanical linkage over the hydraulics in another post. Is that the only reason you don't like them? Do you find the mechanical linkage easier to setup over the hydraulics?

      2001 Camaro Z28 (DD)
      LS3 525hp GM crate engine, built 4L60e
      1974 Camaro Z28 Type LT
      Solid roller 355 sbc with T-56


    16. #36
      Join Date
      Aug 2004
      Location
      Walla Walla, WA
      Posts
      1,512
      Country Flag: United States
      Quote Originally Posted by kyphur View Post
      Yeah, now I think reading about how you liked the "feel" of the mechanical linkage over the hydraulics in another post. Is that the only reason you don't like them? Do you find the mechanical linkage easier to setup over the hydraulics?
      I don't think I've ever said anything about the "feel." I find factory mechanical linkages (as in a first generation Camaro) easier to setup, adjust and trouble shoot. There's only so much you can do with the concentric hydraulic throwout bearing in the stock linkage without removing the T56. That's a pain.

      As an example, there's another thread here (I think) from a guy who's spent the better part of 2 weeks or more trying to get his stock hydraulic linkage to work with aftermarket parts that "are supposed to work together." That simply wouldn't happen with a mechanical linkage.
      Mike Kelcy - '68 Camaro with some stuff done to it.

    17. #37
      Join Date
      Jan 2006
      Location
      Houston, Tx
      Posts
      1,004
      Country Flag: United States
      This is getting to be a really good thread... I spoke with the gear box and may end up going the mechanical route for simplicity sake.

      Did you ever get your BRP Crossmember installed? That is the next fight. Trying to figure out what crossmember will work with an LS1 T56 behind a small block.

      I may go the route of the classic chevy one that kyphur posted up

    18. #38
      Join Date
      Aug 2004
      Location
      Walla Walla, WA
      Posts
      1,512
      Country Flag: United States
      Quote Originally Posted by Taylor1969 View Post
      Did you ever get your BRP Crossmember installed?
      LOL, no, I'm still debating whether to install the 383 or the LS1 that are both sitting in the shop.
      Mike Kelcy - '68 Camaro with some stuff done to it.

    19. #39
      Join Date
      Jan 2006
      Location
      Houston, Tx
      Posts
      1,004
      Country Flag: United States
      Got my T56 Yesterday!!!

      So if I go mechanical linkage - can ya'll help me with a shopping list? I will post up all my results both here and at camaros.net in the T56 thread.

      From what I gather I need the following:

      Is this everything?

      For reference - here are the current costs from Ricks First Gen for everything but the heim linkage rods:

      CL-4 Camaro Clutch Bellcrank Pivot Ball & Stud, Engine Block Side, 1967-1969 --Part# CL-4 $13.99
      CL-12 Camaro Clutch Fork, GM, 1967-1969 --Part# CL-12 $63.99
      CL-46 Camaro Clutch Bellcrank Upper Push Rod Boot, 1967-1969 --Part# CL-46 $8.99
      CL-6 Camaro Clutch Return Spring, Small Block, 1967-1969 --Part# CL-6 $5.99
      CL-15 Camaro Clutch Bellcrank Assembly, Small Block, 1967-1969 --Part# CL-15 $40.99
      CL-3 Camaro Clutch Bellcrank Frame Side Pivot Mounting Bracket, 1967-1969 --Part# CL-3 $12.99
      CL-19 Camaro Clutch Throw Out Bearing, 4-Speed Transmission, GM, 1967-1969 --Part# CL-19 $47.99
      CL-18 Camaro Clutch Bellcrank Push Rod Retaining Clip, 1967-1969 --Part# CL-18 $2.50 (*3)

      Does not include Shipping Charges Subtotal: $202.43

    20. #40
      Join Date
      Jan 2006
      Location
      Houston, Tx
      Posts
      1,004
      Country Flag: United States
      dbl post

    Page 2 of 6 FirstFirst 1 2 3 4 5 6 LastLast



    Advertise on Pro-Touring.com