Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Page 1 of 2 1 2 LastLast
    Results 1 to 20 of 26
    1. #1
      Join Date
      Apr 2017
      Location
      Florida
      Posts
      10
      Country Flag: United States

      69 Camaro 2" Drop Spindle Dilemma

      I'm finishing up my 69 Camaro build and have run into a bit of a problem.

      I can only turn the steering wheel about 3/4 of a turn either direction and the tire hits the front of the fender.

      I've seen several posts that say NOT to use 2" drop spindles on first gen Camaros.

      Not sure where to turn... Any info and/or suggestions would be greatly appreciated

      My car is currently equipped with the following

      TRSD aka The Right Stuff Detailing front disk brakes with their 2'" drop spindles

      Viking Coil Overs

      OEM Control Arms - I plan to install a set of tubular upper and lower control arms. However, I'm told this will not resolve the turning problem.

      Vision Torque 8.5" Wheel 4.5" BS -6mm OS

      MT Street Comp Tires 245/40/18

      I have moved around the alignment shims and gained a little more turnability but not enough.

      Please let me know if you need more info or photos showing specific parts. Look forward to hearing from you soon.
      Attached Images Attached Images  

    2. #2
      Join Date
      Apr 2009
      Location
      Michigan
      Posts
      336
      Country Flag: United States
      This might not be what you want to hear, but the best solution would be to run wheels with more backspacing to give you more tire to fender lip clearance.

      Luckily, it looks like Vision Wheel makes the Torque wheel in an 18x8.5 with 5.1" backspacing as well, which would give you 0.6" more clearance at the fender. Hopefully that would be enough. Somebody running a similar setup could probably tell you if that size and offset would rub on the sub-frame at full lock. Looks like $142 each on Summit: https://www.summitracing.com/parts/v...mml1/overview/
      - Ryan

    3. #3
      Join Date
      Apr 2017
      Location
      Florida
      Posts
      10
      Country Flag: United States
      Thanks for the info Ryan. I considered trying that but as you mentioned it might cause the tire to rub the frame... I don't want to trade one problem for another.

      That would be great if someone else on here was successful with the same setup and that backspacing.

    4. #4
      Join Date
      Nov 2008
      Location
      Milwaukee, WI USA
      Posts
      440
      Country Flag: United States
      Dump the drop spindles, they are nothing but problems on first gen Camaro's...
      1969 Camaro SS, 350(NOM), M21, 12 Bolt Posi, 01B (Jan 69) LOS Build

    5. #5
      Join Date
      Apr 2017
      Location
      Florida
      Posts
      10
      Country Flag: United States
      Thanks for your reply 77Thor. That seems to be what most posts say. I haven't seen much explanation why though...

    6. #6
      Join Date
      Nov 2006
      Location
      Mountain Springs, Texas
      Posts
      4,880
      Country Flag: United States
      I dunno. ridetech uses drop spindles with good results. There can be issues with wheel interference with smaller diameter wheels.

      Don
      1969 Camaro - LSA 6L90E AME sub/IRS
      1957 Buick Estate Wagon
      1959 El Camino - Ironworks frame
      1956 Cameo - full C5 suspension/drivetrain
      1959 Apache Fleetside

    7. #7
      Join Date
      Apr 2017
      Location
      Florida
      Posts
      10
      Country Flag: United States
      Thanks for chiming in Don. I'm sure there are different applications where the 2" drop spindles work OK. Unfortunately the majority of posts and online research shows nothing good with first gen Camaros specifically 69's. Seems there is never an easy answer to modifying these cool old muscle cars...

    8. #8
      Join Date
      Nov 2006
      Location
      Mountain Springs, Texas
      Posts
      4,880
      Country Flag: United States
      Your issues are not due to the drop spindles imho. Wheel backspacing and alignment are the issues imho....

      Don
      1969 Camaro - LSA 6L90E AME sub/IRS
      1957 Buick Estate Wagon
      1959 El Camino - Ironworks frame
      1956 Cameo - full C5 suspension/drivetrain
      1959 Apache Fleetside

    9. #9
      Join Date
      Apr 2017
      Location
      Florida
      Posts
      10
      Country Flag: United States
      Hi Don, good news with that scenario is less labor and $$$

    10. #10
      Join Date
      May 2015
      Location
      Georgia
      Posts
      147
      Country Flag: United States
      I'm building my 69 camaro and running Heidts pro G Front subframe with their 2 inch drop spindles. I just mocked up a 275-35-18 tire on a wheel fitment tool so I could order wheels. On my subframe I need my 18x9 wheel with 5.25 BS. The tire is close to my front swaybar at full lock, but I wanted to make sure I had as much clearance on the inner fenders.



    11. #11
      Join Date
      Nov 2006
      Location
      Mountain Springs, Texas
      Posts
      4,880
      Country Flag: United States
      Quote Originally Posted by markaaron80 View Post
      I'm building my 69 camaro and running Heidts pro G Front subframe with their 2 inch drop spindles. I just mocked up a 275-35-18 tire on a wheel fitment tool so I could order wheels. On my subframe I need my 18x9 wheel with 5.25 BS. The tire is close to my front swaybar at full lock, but I wanted to make sure I had as much clearance on the inner fenders.
      I am surprised that is enough backspacing. Was the suspension at ride height when you did the measuring?

      Don
      1969 Camaro - LSA 6L90E AME sub/IRS
      1957 Buick Estate Wagon
      1959 El Camino - Ironworks frame
      1956 Cameo - full C5 suspension/drivetrain
      1959 Apache Fleetside

    12. #12
      Join Date
      Oct 2018
      Location
      San Jose, CA
      Posts
      528
      The tru-turn first gen cars seem to be running 5.5-6” bs with a 275-315 tire size. FWIW.
      1971 Camaro - 406 / T56
      2016 Camaro SS convertible
      2018 Colorado 4x4

    13. #13
      Join Date
      Nov 2006
      Location
      Mountain Springs, Texas
      Posts
      4,880
      Country Flag: United States
      Quote Originally Posted by c4racer2 View Post
      The tru-turn first gen cars seem to be running 5.5-6” bs with a 275-315 tire size. FWIW.
      And a lot of negative camber if I remember right.

      Don
      1969 Camaro - LSA 6L90E AME sub/IRS
      1957 Buick Estate Wagon
      1959 El Camino - Ironworks frame
      1956 Cameo - full C5 suspension/drivetrain
      1959 Apache Fleetside

    14. #14
      Join Date
      May 2015
      Location
      Georgia
      Posts
      147
      Country Flag: United States
      Quote Originally Posted by dhutton View Post
      I am surprised that is enough backspacing. Was the suspension at ride height when you did the measuring?

      Don
      Yes, it was at ride height. All of the tire and maybe 1/2 inch of the front rim was behind the front fender. Fairly low in my opinion. This was with a 18x9 wheel. So an 18x10 would add another 1/2 inch of backspacing to that.

    15. #15
      Join Date
      Oct 2007
      Location
      Georgetown/Austin, TX
      Posts
      307
      Country Flag: United States
      The Vision Torque 18x8.5 with 5.1" Backspacing should be just fine, but I'm not 100% sure with the stock control arms. That backspacing would work for sure with almost any aftermarket control arms. I also suspect that there could be something going on with your alignment.

    16. #16
      Join Date
      Apr 2017
      Location
      Florida
      Posts
      10
      Country Flag: United States
      Thanks again to everyone for responding. Just wanted to share a quick update: I added several alignment shims to the OEM control arms which provided negative camber and positive caster. Listed below are results...

      Left turn to the steering stop and does not hit the front of the fender or rear part of the wheel well on either side but it's very close. Also, the inside of tire just barely rubs the frame when its on the steering stop. No big deal. However, not sure but I don't any more backspace will help me?

      Right turn is still rubbing the front fender on the driver side and the rear wheel well on passenger side.

      Plan on tweaking the shims a bit more... Will report more results soon

    17. #17
      Join Date
      Nov 2006
      Location
      Mountain Springs, Texas
      Posts
      4,880
      Country Flag: United States
      Quote Originally Posted by Wrobotech View Post
      Thanks again to everyone for responding. Just wanted to share a quick update: I added several alignment shims to the OEM control arms which provided negative camber and positive caster. Listed below are results...

      Left turn to the steering stop and does not hit the front of the fender or rear part of the wheel well on either side but it's very close. Also, the inside of tire just barely rubs the frame when its on the steering stop. No big deal. However, not sure but I don't any more backspace will help me?

      Right turn is still rubbing the front fender on the driver side and the rear wheel well on passenger side.

      Plan on tweaking the shims a bit more... Will report more results soon
      More negative camber, you will likely need a lot. Less caster on the side that is rubbing on the rear.

      Don
      1969 Camaro - LSA 6L90E AME sub/IRS
      1957 Buick Estate Wagon
      1959 El Camino - Ironworks frame
      1956 Cameo - full C5 suspension/drivetrain
      1959 Apache Fleetside

    18. #18
      Join Date
      Apr 2017
      Location
      Florida
      Posts
      10
      Country Flag: United States
      Thanks for the suggestion Don. Some of my research shows that 2" drop spindles allow for additional camber with OEM control arms. Does that make sense or am I misunderstanding how it works?

    19. #19
      Join Date
      Feb 2013
      Posts
      1,560
      Country Flag: United States
      Quote Originally Posted by 77thor View Post
      Dump the drop spindles, they are nothing but problems on first gen Camaro's...
      Not necessarily.
      Quote Originally Posted by Wrobotech View Post
      Thanks for your reply 77Thor. That seems to be what most posts say. I haven't seen much explanation why though...
      I have an explanation below for you as to why they're not all problems.
      Quote Originally Posted by dhutton View Post
      Your issues are not due to the drop spindles imho. Wheel backspacing and alignment are the issues imho....

      Don
      Correct. At this point, it sounds more like a wheel fitment issue. That's also a little bit taller of a tire diameter than we see these days.

      The drop spindle with our kit is designed to do two things:
      - Creates negative camber gain because of the taller design
      - Lower the car 2"

      Because we're using this spindle to get the lowered stance instead of a shorter stroke shock, we gain ride quality and handling by not sacrificing shock travel. It's all set up around factory track width as well. The only chance of someone changing track width with our kit is dependent on what brake kit they choose (which could also be part of your issue with your current setup).

      If you're wanting to change to a tubular arm setup, look into our Strongarms, spindles, and coilovers. On the control arms, we've moved the balljoints for more caster, put in delrin bushings for smoother movement of the arms, and have the drop pocket so we can run the longer shock for a better ride. From everything you're saying, I would venture to guess is more of a backspacing/tire height issue though. I still believe that would need to be addressed as well, especially if you're wanting the lowered stance.


      Ridetech Suspsension
      Tech Specialist
      Phone: 812.481.4734

      Project Fox
      1979 Trans Am

    20. #20
      Join Date
      Nov 2006
      Location
      Mountain Springs, Texas
      Posts
      4,880
      Country Flag: United States
      Quote Originally Posted by Wrobotech View Post
      Thanks for the suggestion Don. Some of my research shows that 2" drop spindles allow for additional camber with OEM control arms. Does that make sense or am I misunderstanding how it works?
      I think it depends on the height of the drop spindle and where your ride height is. But I am not a suspension guru.

      Just stack up the shims and see what you can get.

      Don
      1969 Camaro - LSA 6L90E AME sub/IRS
      1957 Buick Estate Wagon
      1959 El Camino - Ironworks frame
      1956 Cameo - full C5 suspension/drivetrain
      1959 Apache Fleetside

    Page 1 of 2 1 2 LastLast



    Advertise on Pro-Touring.com