Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Results 1 to 7 of 7
    1. #1
      Join Date
      Jan 2015
      Posts
      38
      Country Flag: Canada

      1962 TBird unibody bracing

      Wasn't sure where to post this, so I hope this sub forum is correct.

      I'm trying to plan out how to brace my 62 TBird. My main focus is torsional, as every picture I've seen of these cars pushed "hard" has horrendous suspension induced body roll but more importantly fro this thread, you can actually see twist in the chassis. I don't see a lot of sense working on suspension if the chassis is moving like noodles that have been cooked al dente....

      The following pics aren't my car, mine is a hard top (which is a plus in the torsional sense). I trying to avoid intruding on the passenger compartment since it's going to be a driver as well as weekend toy. Which pretty much rules out a roll cage. Besides, the fam has no interest in squeezing around bars and hoops to get it. Not to mention I wouldn't want my daughter's head to bounce off a rear rear hoop in an accident.

      I'm still sussing out the suspension details, so I'm staying stock right down to the leaf springs until I've got a cohesive plan figured for front and rear. I'm back and forth on the front but coil overs will probably be the route and play with suspension geometry a bit. Maybe see if the "shelby drop" works on this car. The rear I'm pretty sure I've at least decided on coil overs and a watts link (which probably puts me in 3 link territory). The rest I'm still racking my brain over. Stock suspension will at least allow me to enjoy it this summer while I work on the final plan. but suspension is another topic for another thread.

      I've done a little photochop stuff to help illustrate my thoughts. I would appreciate input or opinions on if it makes sense or better ideas on how to go about it.

      The floor is already at the bottom of the unibody rails and the car sits pretty low as delivered. I don't plan to lower it any further, but I still don't have a lot of room to work with under the car.

      So, here goes.

      Stock underbody:





      The rockers have some rot, so they will get 2x4 square tube inside them and stitched back up (the red represents the leaf spring space)



      some subframe connectors seem like a logical first step, as well as tying together what looks like bracing that just stops in the middle of nowhere



      Some "gusseting" at the rocker ends should help and maybe double up the rear frame rails where there is space



      last thing I can think of is a driveshaft hoop to help tie the two sides of the rear most cabin/floor crossmember together



      Now the stock Engine bay



      Factory style tower braces are an easy beef up and install, OEM did the design work here already



      Chuck in a monte carlo style brace a la the mustang designs



      Beef up the cowl with 2x2 square tube and other than welding up the spring towers (old Carrol Shelby trick with mustangs) I'm pretty much out of ideas inside the bay



      I plan to tie the front door pillars together with round tube up and under the OEM dash. My 300M has it and it makes a big difference in how that car feels with it in and out



      Trunk area will be tied together under the package tray, then run bracing back to the rear leaf spring mounts. should help keep the rear of the car stiff, at least it should support the rear leaf spring points while I'm still running the leafs. The cross bar at the back of the trunk will help stiffen it up some torsionally, That space is useless anyways as that "dip" is where the spare tire resides.The cross bar will be just aft of the spare tie. For such a big car, the trunk is pretty useless for much more than a set of golf clubs and a picnic basket. Wide but very shallow.



      The front clip doesn't tie into the center body very well, it's all bolted on. Not the best IMO, at least not from a rigidity perspective. Need to get some welded areas in there I'm thinking



      A beefed up brace from the spring tower to the a pillar should help as well as tiying it into the cowl brace and then down to the rockers



      And that's about as far as I've gotten.

      Any thoughts or ways to change/improve my plans?
      BJ
      1962 Thunderbird hardtop
      Currently a bucket O' rust

    2. #2
      Join Date
      Jul 2014
      Location
      Las Vegas , Nevada
      Posts
      44
      Country Flag: United States
      The only change I would make is the ones in the engine bay . Just two more black bars from the rad. surport to the wheel wells in a diamond shape . And I am using drive line hops and a X-Bar to stiff up the bottom of mine . Nice to see another Thunderbird guy that that likes curves .
      800 Amp Time Attack Thunderbird

    3. #3
      Join Date
      Jul 2014
      Location
      Las Vegas , Nevada
      Posts
      44
      Country Flag: United States
      Almost forgot , they make a cover for the back seat for that year Thunderbird that you can reinforce with hopes for Track Days . An unbolt an have room for people the rest of the time .

      800 Amp Time Attack Thunderbird


    4. #4
      Join Date
      Jan 2015
      Posts
      38
      Country Flag: Canada
      Quote Originally Posted by Bird of Prey View Post
      Almost forgot , they make a cover for the back seat for that year Thunderbird that you can reinforce with hopes for Track Days . An unbolt an have room for people the rest of the time .
      I believe that's the fiberglass tonneau cover for convertibles to turn them into "roadsters" that you are thinking of.

      Mine is a hard top.

      Your "Torino Bird" is also a full frame car (like 'em, used to have one I dropped a 460/C6 into) . My "bullet bird" is a unibody. Little different setup. Mine is more early mustang type construction so that's kind of where I'm taking the reinforcement ideas from.

      I looked at the engine bay "diamond" design. I'm a bit skeptical of anything forward of the spring towers doing much more than adding weight. A diamond shape isn't triangulated and is kind of flexible by the nature of its design. The mustang style braces that "sort of" make a diamond shape usually go from the rad panel to the monte Carlo style bar and still don't look to do much more than brace the rad panel to me. From the towers to the rad panel would more support the rad panel than the towers. The towers are a much more rigid construction than the rad panel.

      Thanks for the reply.

      All discussion is good.

      BJ
      1962 Thunderbird hardtop
      Currently a bucket O' rust

    5. #5
      Join Date
      Jul 2014
      Location
      Las Vegas , Nevada
      Posts
      44
      Country Flag: United States
      The Drive shaft hopes I was thinking of are the ones the mopor guy's use on there uni-body cars for drag racing . And see if the Lincoln frame surport off the 69 to 76 Marks an Continintil can help . They might be overkill ...... It's a big block ford , never mind . Maximum Motorsports or Agent 47 make stuff(little) for uni-body cars like old Cougar's and 86 to 95 Thunderbird .
      800 Amp Time Attack Thunderbird

    6. #6
      Join Date
      Nov 2012
      Posts
      3
      Country Flag: United States
      I'm planning on going the same route with my 67 mustang coupe, insofar as to keep stockish suspension and brace the unibody first. One thing for a hardtop that I'm planning on doing, is to brace behind the rear seats with either a panel like this one: http://www.stangnet.com/mustang-foru...er-jpg.344585/ (which should have some beads rolled into it) or with an X style tubular brace. If you go the panel route, this doubles as a firewall for the gas tank/trunk area. Also might help in a unfortunate side impact (knock on metal).

    7. #7
      Join Date
      Apr 2005
      Location
      Colorado Springs
      Posts
      761
      Some of the white papers I've read on chassis stiffness point to the front third of the car needing significantly more support than the rest of the car, especially around the A pillar area. As a convertible, you may need some additional rocker area support as well. You could most likely skip all the rear reinforcement.

      A good read for chassis rigidity in general and Ford guys in particular is the SN95 project. Search for it on here and read through their findings and research and you can learn a lot of uni-body reinforcement.
      TonyC@HP2




    Advertise on Pro-Touring.com