Activity Stream
-
Older Activity
-
20 Minutes AgoNumbers matching does not seem to be what it used to be. So go on then, full custom - you know you'll be happier making it your own!8 replies | 314 view(s) -
54 Minutes AgoIt’s got a non-matching 455 in it currently. The original 400 was pulled(on a stand since then covered up) in the 80’s for the 455 just because he...8 replies | 314 view(s) -
1 Hour AgoI thank you for the reply. I appreciate the help with the sanity check. I didn't want to muddy the water from the start but I'm also running...3 replies | 29 view(s) -
1 Hour AgoEngine working angle 5.3-1.1=4.2 working driveshaft angle Diff working angle 1.1-2.1=1.0 working driveshaft angle You need these 2 angles to be...3 replies | 29 view(s) -
3 Hours AgoSo my .02. LOL. 1. Since its a numbers matching engine wise I would pull the 400 and have a trusted engine shop go thru it. Pontiac engines were...8 replies | 314 view(s)
-
3 Hours AgoAt this point I’m torn for plans. It’s a solid old survivor car so half of me wants it back all original(got the original 400 with it too) and...8 replies | 314 view(s)
-
5 Hours AgoA slight update, you may consider ignoring previous data. I have a couple different transmission mounts to work with. I installed a taller trans...3 replies | 29 view(s)
-
6 Hours AgoWhat are your plans for it? Good looking car.8 replies | 314 view(s) -
6 Hours AgoHello all, Working on a 69 F-body. I've installed a 4l80e and ford 9" and I'm struggling with wrapping my head around some of the angles. I did...3 replies | 29 view(s)
-
12 Hours AgoHello everyone! I'd like to introduce our '72 Firebird 400: Since getting the car we've put quite a bit of work into the interior using...0 replies | 21 view(s)
-
18 Hours AgoSTREETFIGHTER50 started a thread Will this UMI Front Frame Brace work with this Ridetech Modular Front Sway Bar? in SuspensionOn a 64-67 A-Body https://www.umiperformance.com/4063-1964-1967-gm-a-body-front-frame-brace/ ...0 replies | 38 view(s) -
21 Hours AgoPrice reduce2 replies | 1118 view(s)
-
22 Hours AgoStill available ?2 replies | 444 view(s)
-
23 Hours AgoGot the Eastman's Bare Metal Epoxy on the underside and Firewall today also got the new Engine Mounts done and installed as well. I raised the Engine...14 replies | 5434 view(s) -
1 Day AgoSo some pics of my 67 I did a number of years ago for your inspiration. LS swap. Was great project.4 replies | 143 view(s)
-
1 Day AgoThanks for the info and sharing. Beautiful cars!4 replies | 238 view(s) -
1 Day AgoMotor: Rebuilt LSA by BoostMode LS short black assembled by LME LSA with solid isolator Wegner LSA drive kit BTR .660 springs titianiim plates...1 replies | 251 view(s) -
4 replies | 143 view(s)
-
1 Day AgoMounted a dead pedal. It was getting annoying not having a place to put my foot. This was from an Audi R8. Matches perfectly to the ZL1 pedal covers341 replies | 173469 view(s)
-
1 Day AgoMade some progress over the last few weeks. Got the Body fitted to the Chassis relatively pain free. The Convertible Body has a couple differences...14 replies | 5434 view(s)
-
1 Day AgoNice to get an old friend back!!4 replies | 143 view(s)
-
4 replies | 143 view(s) -
2 Days Ago60 replies | 31951 view(s) -
2 Days AgoI just read this, start to here. Good work man.268 replies | 133981 view(s)
-
2 Days AgoGoing to start a thread for the build of my 1967 Nova. I bought this car in 1992 built and drove it daily for years, raced and showed it, and then...4 replies | 143 view(s)
-
2 Days Ago0 replies | 97 view(s) -
2 Days AgoHere are a couple more photos...we haven't taken many since we finished the car. We're running a Wildwood epb on the 79. 275 35 18 in the front of...4 replies | 238 view(s) -
2 Days AgoGreat work on the Nomad. The dial a boost bracket scares me that you will cut your leg on it. Looks to be right where your leg and knee would hit...268 replies | 133981 view(s)
