Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Results 1 to 20 of 84

    Threaded View

    1. #11
      Join Date
      Oct 2012
      Location
      British Columbia
      Posts
      614
      Country Flag: Canada

      Undercoat gone and getting ready for Sandblasting

      FINALLY I'm done scraping off undercoat. I've found a guy to do the sandblasting for me but he is twice the money I've been quoted and is booked weeks in advance. The Camaro will be going to him in April with big factor being when I finally got him on the phone (he was always in the shop when I called) he took the time to answer my questions and he even had the right answers. I did my homework and did some reading on here before I started calling people and even went to a couple shops to see their operations. Sadly most of the guys I talked to were clearly not very knowledgable on sandblasting older cars and their bad/messy/filthy looking shops just eliminated them from my list. I only have one '67 Camaro and I'm not about to let just anyone blast away at it.

      On to the updates;

      Ive stripped all the glass and interior out of the car, when I got down to the bones I found the dash was rusted and had been covered up so I wanted to replace it. My local jobber has a guy who is into and knowledgable on old cars. He has given me some great advice and showed me that I have some options when it comes to getting some replacement parts. Not to start a battle with anyone, but from what I see there are some options when it comes to buying replacement panels. My guy, Thanks Rick, showed me that C2C gives you the option on USA made or off shore. I've picked up some US made stuff and the metal is thick and it fits very well, I'm a happy camper and its well worth the extra couple bucks to me.



      http://c2cfabrication.com/gm/chevrolet/camaro/

      Thought I would share a little on how I took the dash out of the car. Please feel free to send me any suggestions you have as I will be taking on my quarter panels and some floor work in the future. Hope this helps someone with taking on their own project as it really isn't hard stuff if you just take your time.

      Here is the damaged dash that has been patched and bondo over the rust by a earlier owner

      Name:  image 2(13).jpeg
Views: 2386
Size:  56.3 KB


      First I found the "dimples" along the dash where it was spot welded at the factory
      Name:  111image.jpeg
Views: 2418
Size:  26.9 KB

      Then I used a small sharp drill bit to put a small pilot hole in the centre* (*that's how we spell center in Canada)

      Name:  114image.jpeg
Views: 2437
Size:  27.0 KB

      Then I used a stepped drill bit to drill through the pilot hole while using a screw driver to apply light pressure up on the metal until you feel the metal pop loose


      Name:  113image.jpeg
Views: 2425
Size:  27.4 KB

      Here is a short video I shot so please excuse the shaking and the out of range shots. What I was trying to show was how the multi stepped drill bits work for drilling out spot welds. When I use this bit it goes in the small pilot hole I've already drilled and I ususlly use my other hand to hold the screw driver to lightly pry up on the weld so when the stepped bit makes a big enough hole the metal pops up. Really nice and simple and makes just enough of a hole to take out the spot weld.

      http://youtu.be/5INrhOp0K-k

      I got sorta lucky with the rust doing most of the work along the front of the dash so I just used some tin snips to remove the little bit of metal along the front of the dash.
      Name:  112image.jpeg
Views: 2445
Size:  42.0 KB
      The upper cowl metal was in relatively good shape so will just do a light grind along the upper cowl and a little metal repair and I should be good to go and install my new dash upper.
      Name:  i110mage.jpeg
Views: 2415
Size:  42.8 KB
      Here is the old upper dash out of the car and it was super easy to do. I will post some more updates when I install the new upper dash.

      Name:  117image.jpeg
Views: 2374
Size:  42.4 KB
      Todd
      '14 ZL1, 6 speed and 6.2L of Super Charged Awesome!
      '67 Camaro SS in process. A long, slow, expensive trip...


      How hard can it be...

      Project Obsession
      https://www.pro-touring.com/showthre...ject-Obsession





    Advertise on Pro-Touring.com