Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Results 1 to 8 of 8

    Hybrid View

    1. #1
      Join Date
      Apr 2005
      Location
      IN/MI border
      Posts
      1,920
      Country Flag: United States

      68 camaro Steering Arm offset??

      So as I was looking at the front end of the camaro and was curious if one can offset the steering arm that is bolted to the spindle to allow an additional 1/2" of room to possibly get a 8.5" wide wheel on the front. Has anybody tired this? It does't seem like it would affect the steering any further (other than slightly less turning radius) and is still keeping the tie rods in line. Would this be feasable or even safe for that matter? This would incorperate a 1/2" steel spacer between the spindle and steering arm. Any further out and the bolt head would interfere with the sway bar link at full turn.

      Last edited by BuddyP; 02-21-2012 at 10:13 PM.


    2. #2
      Join Date
      Nov 2008
      Location
      Lawrenceburg, TN
      Posts
      4,098
      Country Flag: United States
      I think The FAB53 '72 Nova of Jon Rasmussen has home made shims and longer bolts to move the steering arms in look for there thread

    3. #3
      Join Date
      Jul 2005
      Location
      Den Helder, the Netherlands
      Posts
      1,148
      Country Flag: Netherlands
      Quote Originally Posted by BuddyP View Post
      . . . . .to possibly get a 8.5" wide wheel on the front.
      Been driving my 67 for more than 10 years with a 8.5" wide (17") wheel on the front. No mods to the steering arms . . . . .

    4. #4
      Join Date
      Oct 2004
      Location
      Indiana
      Posts
      1,371
      Dont know your budget, but you might consider this: http://www.ridetech.com/store/tru-turn/
      Bret Voelkel
      Director of Innovation Fox Powered Vehicles Group
      Founder/ Former Owner
      RideTech/Air Ride Technologies, Inc.

      How do you spell Impossible?

    5. #5
      Join Date
      Jun 2009
      Location
      Central FL
      Posts
      1,231
      I tried that, couldn't get it to align correctly, so I just spaced the wheel out. Running 9.5in.
      Dan
      1968 Camaro v2
      LS6 :: Viper T56 :: C5 Brakes :: Hotchkis Suspension


    6. #6
      Join Date
      Apr 2005
      Location
      IN/MI border
      Posts
      1,920
      Country Flag: United States
      Bret, yes I've been eyeing your front coil over kit and took a hard look at it at SEMA. But for now I need to watch close on bidget to get this done and on the road. Basically I didn't want buy a narrower wheel then have to get the thing rehooped down the road when I get your kit! So this "mod" would be a cheap stop gap.

    7. #7
      Join Date
      Dec 2009
      Posts
      261
      Country Flag: Canada
      You'd get a (probably good) increase in Ackermann, and also a (definitely bad) increase in bump steer. I'm not sure if you could fix the increase in bump with tie rod spacing , you'd probably have to alter the inner mounting point a similar amount to get rid of the bump. How much worse it would be though, I don't know.
      Last edited by ace_xp2; 02-22-2012 at 10:08 AM. Reason: beat by 2 minutes!

    8. #8
      Join Date
      Apr 2009
      Location
      san diego
      Posts
      5,101
      Country Flag: United States
      You need to check how this will affect ackermann. Obviously a shorter tie rod and bump steer will also need to be looked at and adjusted.




    Advertise on Pro-Touring.com