Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Results 1 to 9 of 9
    1. #1
      Join Date
      Aug 2009
      Posts
      277

      radiator mods for LS engine swap

      Looking to have a Mark 7 unit built and it will be fine in stock form for my Pontiac motor. I may LS the car in the future and I hear people talking about steam bypass all the time. What is this for and should I make provisions for this in the radiator? If so, where would it go?



    2. #2
      Join Date
      Jun 2009
      Location
      Cape Coral, FL
      Posts
      323
      Country Flag: United States
      I believe its for the steam that accumulates in the engine, all I know is I have an outlet infront of my driver side head for it on my LS2. I've seen a lot of people tap into the top of the water pump so there is no need to run the line to the radiator. I'm actually concidering doing the same to mine, since both radiator hoses are on the passenger side anyways, the steam line to the radaitor just gets in the way if you decided to run the intake into tha corner of the radaitor support.

    3. #3
      Join Date
      Feb 2010
      Posts
      154
      Country Flag: United States
      Hey old66 your on here as well as PY, cool! Good to see more Pontiac people around. The steam vent is to get the air bubbles out that get trapped at the top of the coolant passages in the cylinder heads. In mine I simply added a "tee" in the upper rad hose with the provision to run the steam vent to that.
      BJ

      66 GTO LY6/4l80e

      Build Thread on LS1tech


    4. #4
      Join Date
      Aug 2009
      Posts
      277
      Thanks...I am back and fourth. PY only gets me just so far and then i have to go the rest of the way with the PT guys. I was not really wanting to go to the radiator.

    5. #5
      Join Date
      Apr 2005
      Location
      Cartersville, GA
      Posts
      1,298
      Country Flag: United States
      I have done it both ways (going back to the water pump, or getting the vent tube added when having a new radiator made), and couldn't tell any difference, but now I use RnD Fabrication radiators for all my LS swaps, and they are already set up for it. Give Sparky a shot, he can build the radiator pretty much however you want it.
      Joe Hinds

    6. #6
      Join Date
      Jun 2010
      Location
      Georgia
      Posts
      2,178
      Country Flag: United States
      yep, we can build them with the port at no additional charge, or you can drill & tap the pump if you don't want to run a steam line. If you are not running an LS now, you might keep what you have until you swap, as the LS motors require a passenger side orientation for the inlet and outlet (which might not work so well for your current motor).

    7. #7
      Join Date
      Aug 2009
      Posts
      277
      That's odd. I have seen others running LS engines in cars with drivers side top hoses and passenger side lower hoses. Why the need for them to come in the same side?

    8. #8
      Join Date
      Feb 2010
      Posts
      154
      Country Flag: United States
      Most LS waterpumps will run the hoses both on the passenger side. In my case I got the waterpump that outputs on the top drivers side. I have my battery on the drivers side, and my intake going to the passenger side. Nothing crosses over each other, it was what I felt to be the cleanest option.

      If you were to buy a specific LS swap radiator most likely it will have both inlet and outlet on the passenger side. I chose a crossflow style that has the opposite sides again for aesthetics.
      BJ

      66 GTO LY6/4l80e

      Build Thread on LS1tech


    9. #9
      Join Date
      Jun 2009
      Location
      Piqua, Oh
      Posts
      397
      Country Flag: United States
      My engine came from an '02 Camaro SS, it had a PS cooler in the top hose that went to the drivers side. I decided to use the cooler, so thats where it goes. If I had it to do again I would get both outlets on that pass. side. JMO
      Mike South
      1968 Camaro SS/RS LS1/T56
      Ride Tech Tru Turn, Ride Tech T/Q Coil-overs
      Ride Tech 4-link




    Advertise on Pro-Touring.com