Buttonwillow June 5-6

[Gitter Dun]

Hoosier

Ya, I have a race the following weekend at Laguna Seca. The calipers I just came up on are used and will probably barely make it through my Laguna weekend, so I'm going to have to pass :(

Sure! if you want to put a deposit down and then sign on the dotted line below for damages

What car and calipers? Might have some you can borrow.

LOL, I hear ya, exactly why I stick to time trials.

[SIK02SS]

What car and calipers? Might have some you can borrow.

LOL, I hear ya, exactly why I stick to time trials.

It's a 2002 Corvette Z06, and I run C6 calipers. I have an AP kit going on soon, just waiting for them to get finished and sent out..trying to avoid spending more $ band-aiding my problem with these already on order

[Gitter Dun]

It's a 2002 Corvette Z06, and I run C6 calipers. I have an AP kit going on soon, just waiting for them to get finished and sent out..trying to avoid spending more $ band-aiding my problem with these already on order

Will 2 piston Baer Track calipers work? If so you could borrow mine.

[CurtiSS 69]

It's a little more than a week away. Hopefully you guys will post some video. Have fun.

Regards

CurtiSS 69

[Gitter Dun]

It's a little more than a week away. Hopefully you guys will post some video. Have fun.

Regards

CurtiSS 69

I've already mounted the Go Pro camera mount to my roll bar. Rear main seal is leaking and hopefully that will be fixed tomorrow. Crossing my fingers.

[SIK02SS]

Will 2 piston Baer Track calipers work? If so you could borrow mine.

I appreciate it, not sure of the piston sizes so....I don't know

No worries though, I'm sure I'll see you guys out there sooner or later.

BTW, I'm signed up for Laguna Seca July 10 with Speed Ventures..and have an SCCA race june 12/13 their as well

[Gitter Dun]

I appreciate it, not sure of the piston sizes so....I don't know

No worries though, I'm sure I'll see you guys out there sooner or later.

BTW, I'm signed up for Laguna Seca July 10 with Speed Ventures..and have an SCCA race june 12/13 their as well

NBever done Laguna before, sounds good, I'll try and make it.

Right now I'm having engine issues. I had NYES racing engines build me an aluminum 427. I dropped it in and fired it up and it had a bad oil leak, was thinking rear main seal. After pulling it out looked more like oil pan. Pulled pan and had all kinds of cork gasket material in it. I took photos. Was also leaking in front of intake. Pissed me off. I was supposed to go to Buttonwillow today but had to fix their **** so I had to cancel. Cost me $30 to cancel.

[SIK02SS]

people still use cork gaskets?? Wow, I don't blame you I'd be livid. Is it an LS based motor, small block, or bb?

[Gitter Dun]

people still use cork gaskets?? Wow, I don't blame you I'd be livid. Is it an LS based motor, small block, or bb?

Yeah, I thought the same thing. I'm not to fond of cork but I actually replaced the old one with cork again only because it was convenient.

It is an aluminum PBM block based on first gen with an LS firing order.

[Gitter Dun]

I appreciate it, not sure of the piston sizes so....I don't know

No worries though, I'm sure I'll see you guys out there sooner or later.

BTW, I'm signed up for Laguna Seca July 10 with Speed Ventures..and have an SCCA race june 12/13 their as well

I put Lagune Seca on my calender for July 10th. If budget allows it I will see you there

[Orngcrush69]

No part...no go...Have fun guys!

[Gitter Dun]

My supervisor let me have Friday off so I'm good to go. Prep car completely Friday, load up tools and gear, then load car. Probly leave my house around 11:30 a.m..

[Gitter Dun]

No part...no go...Have fun guys!

Sorry to hear your not going Dave, Hope to see you at the next one. What part do you need?