Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Page 1 of 2 1 2 LastLast
    Results 1 to 20 of 21

    Thread: It's Stuck!

    1. #1
      Join Date
      Nov 2008
      Location
      TN
      Posts
      960

      It's Stuck!

      Well My hands are not dirty because my parents made me wash my hands before I went on the computer so I would not get it all greasy!



      The problem I'm stuck(quite literally) on is how to get the drag link and the tie-rods apart! and off of the idler arm and pitman arm. I don't need to keep them(the tie-rods and the drag link) since I'm replacing most of the steering components, I just need to get it apart!

      I tried tapping them out with a hammer(I got the outer tie-rods off the spindles), and WD-40 and tapping them out, Jerking, yanking, and prying. Any suggestions?

      Thanks!
      Benjamin


    2. #2
      Join Date
      Sep 2006
      Location
      Henderson,NV
      Posts
      2,870
      Country Flag: United States
      The best way is with a puller but you can screw the castle nut on until it's flush and whack it. The old school trick is to smack the drag link or spindle with the round side of a ball peen hammer. The shock will break them loose. It can take a hell of a lot of hammering however.
      Todd

    3. #3
      Join Date
      Sep 2007
      Location
      Southern California
      Posts
      566
      Country Flag: United States
      A pickle fork and a big hammer worked for me. I borrowed the pickle fork from Autozone for free.

      Jon
      Jon U.

      1968 GTO - SC&C Suspension, Forgeline SO3 Wheels
      Build Thread
      1967 911 with a few mods

    4. #4
      Join Date
      Sep 2006
      Location
      Henderson,NV
      Posts
      2,870
      Country Flag: United States
      Pickle fork as well. I was assuming he had no access.
      Todd

    5. #5
      Join Date
      Nov 2008
      Location
      TN
      Posts
      960
      Great! I'll try those Ideas! Thanks!

    6. #6
      Join Date
      Nov 2008
      Location
      TN
      Posts
      960
      I'm borrowing a pickle fork from a friend of mine so I should be able to get it off.

      Thanks again for all the help!

      Benjamin

    7. #7
      Join Date
      Jul 2005
      Posts
      20
      I'm getting when you said"tap them out", you were tapping the top side? You'll need to pound them from the side. The vibrations will loosen them, not like tapping them out of the hole.
      87 stock GN
      86 T Type SBC single turbo 10.00 at 133
      68 Camaro 468 10.30 at 127.... currently going back on the road 383, TKO, Vintage air.

    8. #8
      Join Date
      Apr 2001
      Location
      Rockford Illinois
      Posts
      3,949
      Country Flag: United States
      If all else fails you can get a high carbon sometimes diamond impregnated cutting wire at most hardware stores that will cut through hardened steel that fits in a hacksaw. Or get a torch and cut the mother off.

    9. #9
      Join Date
      May 2008
      Location
      Sacramento, CA
      Posts
      11
      A pickle fork and a heavy hammer works well and is very satisfying to beat on. I've also had good luck with placing a BIG hammer on one side of the fitting and smack the other side with another hammer. Make sure the nut is backed off and it can help if you can find a way to put pressure on the arm to try to pull the tapered shaft out. Swinging the hammer gets to be an artform.

    10. #10
      Join Date
      Nov 2008
      Location
      TN
      Posts
      960
      I just wanted to thank all of you for the advice and let you know that I got them off... I doused them in WD-40 and let them sit then used a friends pickle fork and with three wacks each they came right off! Boy do I need to get one of these!

      But if you want another problem... Well I have one. The slip yoke(or whatever its called) that connects the steering column to the box is giving me problems. I'm trying to get it apart and I think there is a pin that holds it on(but its really greasy) But I'm not sure if I should pound it out or am I missing another way to get it off?

      Thanks again!

      Benjamin

    11. #11
      Join Date
      Nov 2001
      Location
      Sacramento Ca
      Posts
      6,827
      Country Flag: United States

      or Smack the metal around the joint, not the nut or the top. Hit it HARD on the ridge from casting.
      Tony Langlois
      1966 Corvair Monza

    12. #12
      Join Date
      Jul 2005
      Location
      Marshall , MO
      Posts
      699
      There is a bolt in the rag joint and one at the column. Remove the bolts put a large flat screw driver in the slot and twist it gently to spread the metal apart. You may have to loosen the steering box to get the shaft off.
      Brad Shepard
      69 Malibu
      Marshall, MO

    13. #13
      Join Date
      Nov 2008
      Location
      TN
      Posts
      960
      Um... I looked and I don't see any bolts... Just one little pin(about 1/4-5/16)(I think its a pin anyways) at the box end of the rag joint. This is a Mopar box so I don't know if that's different than a Chevy or a Ford... And I got the steering column all disconnected(I'm trying to get it out) everywhere except where the rag joint connects to the box but cant seem to get it apart. I do need to keep this one because its going back on when I'm done messing with the dash and wiring. Sorry if I wasn't totally clear on what I was doing.

      Thanks again!

      Benjamin

    14. #14
      Join Date
      Jul 2005
      Location
      Marshall , MO
      Posts
      699
      I don't know mopars, but you could probably remove the whole box from the frame.
      Brad Shepard
      69 Malibu
      Marshall, MO

    15. #15
      Join Date
      Feb 2006
      Location
      Idaho Falls, Id
      Posts
      1,341
      Hey Benjamin, it's good to see a younger guy on here rather than on some lame ricer forum lol. It's good to be able to pass our knowledge on to the next generation. For future reference if you ever have an air hammer get a pickle fork for it, it's like butta! I'm not too familiar with mopars but maybe post a pic of the pin you are talking about.
      Traven

    16. #16
      Join Date
      Nov 2008
      Location
      TN
      Posts
      960
      Alright I'll Try to have one by tonight(pic that is). EEEWWW! A rice forum! HAHA! No thanks I like American Muscle! Although those awd talon's like you have(Traven) are ok but when I found out that My Duster weighs less with a V8 then they do.. Well... I have my Duster, so you figure out what I decided
      Benjamin

      Twin Dusters
      '72 Plymouth Duster "Aero Duster" project
      '72 Plymouth Duster "Daily Duster" project
      https://www.pro-touring.com/showthre...RO-DUSTER-quot

    17. #17
      Join Date
      Nov 2008
      Location
      TN
      Posts
      960
      So Here are the pictures of my problem... Just follow the little green arrows. you can see the pin... Does it matter what way it comes out? does it come out and I'm missing another way?

      Name:  STEERING BOX-2.JPG
Views: 277
Size:  90.2 KB

      Name:  RAG JOINT.JPG
Views: 232
Size:  63.2 KB

      Thanks again.
      Benjamin

      Twin Dusters
      '72 Plymouth Duster "Aero Duster" project
      '72 Plymouth Duster "Daily Duster" project
      https://www.pro-touring.com/showthre...RO-DUSTER-quot

    18. #18
      Join Date
      Jul 2005
      Location
      Marshall , MO
      Posts
      699
      Is that a pin or an allen headed bolt? looks like an allen head to me since it is offset to one side and not centered in the shaft.
      Brad Shepard
      69 Malibu
      Marshall, MO

    19. #19
      Join Date
      Jan 2000
      Location
      Thousand Oaks California
      Posts
      10,245
      Country Flag: United States
      I am guessing: I'll bet it's a roll pin you can tap out with a punch.

      If you turn the shaft 180 degrees can you see it on the far side? Does it go all the way through?
      Larry Callahan
      Founder / Administrator — Pro-Touring.com • G-Machines.com • HostMyJunk.com
      SEMA Hot Rod Industry Alliance Hall of Fame — Class of 2026
      Advertise on Pro-Touring.com • Shop Pro-Touring.com Merch

    20. #20
      Join Date
      Nov 2008
      Location
      TN
      Posts
      960
      I thought it was an allen bolt too at first but then I looked closer and I don't see any flats or anything... Just a round hole.

      And yes it does go all the way through.

      I was gonna try to tap it out but I thought I'd check with someone else before I tried to tap it out and mess something up!

      Thanks again!
      Benjamin

      Twin Dusters
      '72 Plymouth Duster "Aero Duster" project
      '72 Plymouth Duster "Daily Duster" project
      https://www.pro-touring.com/showthre...RO-DUSTER-quot

    Page 1 of 2 1 2 LastLast



    Advertise on Pro-Touring.com