Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Results 1 to 10 of 10
    1. #1
      Join Date
      Aug 2004
      Posts
      378

      Removing rust from cast iron?

      I'm going to do a few small things on my car, one of them being painting the master cylinder.



      However, it's got some very fine rust on it, and I need to remove it.

      Any ideas?

      As a different option, how hard would it be to safely smooth it out?

      Thanks!
      Thomas

      Spare Change: 68 Camaro, 300hp/350ci, 700R4


    2. #2
      Join Date
      Dec 2005
      Location
      Dublin, CA
      Posts
      502
      just take a wire wheel to it, should clean right up.
      Brent

      1971 Camaro, LT1, 4L60E

    3. #3
      Join Date
      Dec 2007
      Location
      Pittsburgh, PA
      Posts
      125
      Or, just use por-15 and apply it right over the surface rust.
      Mark


      70 Nova, Hotchkis springs and sway bar GW uppers, Bilsteins, , sub connectors, Smooth firewall hidden wiper motor, LS1, 425 rwhp, 175 NOS Ridetech 4 link HQ Coilovers, Mini tubs, 315's. Ridetech billet gas cap, FLT level 5 4L60E, Yank

    4. #4
      Join Date
      May 2006
      Location
      Orangeville, Ontario Canada
      Posts
      119
      Muriatic Acid, or lots of heat... but that isn't good for a MC. ;)
      1987 Monte Carlo Super Slow - Super Worn Out 355, Carb, Giggle Juice, 3" Duals, 200-4R & 4.56s
      1987 Turtle Buick - T63e, 83s, FMIC, MPE DP, PowerLogger, MAFT Pro, 4" Single, ProPain & 3.08s
      2002 Crapmaro B4C - LS1, A4, SLP Lid, DiabloSport, Cutout & 3.23s
      2007 TrailBlazer Super Slug - LS2, A4, AWD, Tune, CAI, Exhaust & 4.11s

      If you didn't build it, it's not yours.

    5. #5
      Join Date
      Aug 2005
      Location
      Hamilton, NJ
      Posts
      4,319
      Country Flag: United States
      On my MC, I used POR-15 beacuse I wanted gloss black. If you want some other color, I might suggest the same, but mist it with etch primer when it is tacky, then use your paint over it.
      Scott from NJ.

      Vent Windows Forever! ...

      Feather-light suspension, Konis just couldn't hold
      I'm so glad I took a look inside your showroom doors

    6. #6
      Join Date
      Jan 2008
      Posts
      67
      Country Flag: United States
      try this stuff http://www.evaporust.com/ it works great! no joke. Just soak your part in it for a couple hours and it will come out like brand new. The stuff is non toxic and it does not eat rubber or paint. I have used it on gas tanks, nuts and bolts and sheet metal. All with great results. You can also use molasses. search on the web for more info. You can buy evaporust at autozone

    7. #7
      Join Date
      Aug 2004
      Posts
      378
      I was planning on Duplicolor Cast Aluminum for the color. However, I see POR-15 has a silver so that might work. I'll have to check locally.

      Would this stuff be good for the sub-frame? I'm looking for a semi gloss finish that will hold up.
      Thomas

      Spare Change: 68 Camaro, 300hp/350ci, 700R4

    8. #8
      Join Date
      Aug 2005
      Location
      Hamilton, NJ
      Posts
      4,319
      Country Flag: United States
      Those colors are not the same. I suggest sticking to your planned color and do what I outlined.

      A lot of guys use it on the SF. I used it, but etched & then used rustoleum semi-glass black (777 or something liek that) for an oe look. But I used straight POR on my LCAs and it looks fine. That stuff gets tougher over time. It was easier to scratch it a week later than 3 months later. But you must prep for POR - very clean, and if the metal is smooth use their etch stuff. Or it will peel in nice neat sheets.
      Scott from NJ.

      Vent Windows Forever! ...

      Feather-light suspension, Konis just couldn't hold
      I'm so glad I took a look inside your showroom doors

    9. #9
      Join Date
      Aug 2004
      Posts
      378
      I'll go with the straight POR, picked up some tonight. I may use it on the 10 bolt, just to clean it up.
      Thomas

      Spare Change: 68 Camaro, 300hp/350ci, 700R4

    10. #10
      Join Date
      Aug 2004
      Posts
      378
      I just painted the M/C with the POR-15 black, and I think I'm going to leave it black.

      It looks really nice, and since it was cast with a rough surface, I just brushed it on and it look good. Nice and shiny, I would say in between semi-gloss and full gloss.

      Thanks for the help!
      Thomas

      Spare Change: 68 Camaro, 300hp/350ci, 700R4




    Advertise on Pro-Touring.com