Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Results 1 to 3 of 3

    Hybrid View

    1. #1
      Join Date
      Jul 2005
      Location
      Eastern Virginia
      Posts
      3,965
      Country Flag: United States

      Power steering hard line?

      I have been trying to find some 3/8" OD steel hard line to use for my power steering lines routed to the pass side to the pump & reservoir. I need something over 6' long but haven't had any luck locally. And $40 to ship an 8' piece is crazy. I have found a piece with about .040" wall electronically welded 10' long for a whopping $1. Yes one dollar, regular steel, not stainless. My question is will this work? Or am I going to have problems bending something that is not seamless?

      Thanks.

      Scot
      86 Monte SS



    2. #2
      Join Date
      Sep 2006
      Location
      Southern Indiana
      Posts
      4,709
      Country Flag: United States
      Hey scot why are you having so much trouble, all you need is regular 38 flared line. Its rated to handle in the 1000psi to 5000psi range.
      all you need is a good 180 degree line bender to do the tight bends and use old v-groove pulleys for gentler bends.
      I prefer to either use brass or cast iron(steel) compression fittings (try NAPA for the steel ones or give me a pm and I can source some maybe) as the compression fittings doesnt create a restriction like a brass line union will.
      As for getting it over 6 ft long you would have to order a 25 ft roll and then attach it to the proper fitting ends as the longets I have ever seen is 60 inches BUT you might try NAPA or a truck shop may be able to source longer sections. I work at a truck shop and will ask the parts guy. Auto Jet may make some or Truck Pro.
      But for my druthers I almost would think about a pushlock Aeroquip hose, plenty of rating and much easier to route.
      BUT as for running a line that is seamless good luck as it wont hold pressure like 3/8 flared line will. The reason is the lines aremade of several layers welded at the seams then wrapped again, generally 4 layers but some aremore or less.
      IF you can find the Bundy Flex 3/8 brake line it bends smoother but so far the next best is NAPA line.
      Also for joining lines that can have restriction you need to ream the cut ends to clean it of flash or at least use a flairing tools to smooth the opening.
      I also like to check the compressions fittings for the stop inside being machined too small in diameter creating a restriction and heating the fluid, I use a clean ,sharp drill bit and either open those up or take them out completely as the ferules actually seal things, the cast iron ones you dont need to drill out just the brass ones.
      AS for a seamless tubing your looking at a single layer tubing and not hold the heat and pressure the power steering will generate.
      Hit me up Ill help you if you need it.
      Also if you EVER have to repair or splice a brake line the only ones DOT legal are the cast iron ones.
      And they are designed to hold over 10000psi so they are safe for brakes.
      Good Luck
      Lee

    3. #3
      Join Date
      May 2002
      Location
      Northern California
      Posts
      10,716
      Country Flag: United States
      I wouldn't run compression fittings for the reason above but maybe look into a flare coupler or a brass union. They worked fine in the past and I agree check the pass cavity. They are made of brass and you can braze on a tab to be used as a hold down bracket.

      http://www.partsamerica.com/ProductL...Category=4015A pn 3204261
      MrQuick ΜΟΛ'ΩΝ ΛΑΒ'Ε



    Advertise on Pro-Touring.com