Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Results 1 to 10 of 10
    1. #1
      Join Date
      May 2007
      Location
      Eugene Oregon
      Posts
      293
      Country Flag: United States

      Help me pick out a cam

      hey guys I just need help picking out a cam trying to figure out what i can run and whats good out there. Here are the specs of the motor and car. I am looking for mild-rough idle, a powerband from 1,800-7,000 roughly not exact but in that area. I was looking at a few cams listed here.
      Texas Speed
      223/224 @.50 .566/.566 lift 1,600-6,400 choice of 114/112 lobe seperation
      233/239 @.50 .595/.603 lift 1,900-6,500 choice of 113/112 lobe seperation
      comp cams
      222/224 @.50 .566/.568 lift 1,800-6,800
      224/230 @.50 .581/.588 lift 2,000-7,000
      Any other suggestions would be great in helping me.
      Motor and car specs
      4.10 gear with posi
      25.7 Tall tire 12.6 wide
      t-56 6 speed manual with 50% gear reduction in 6th gear
      Motor
      6.0L LS2 stroke out to a 402 c.i. 6.6L
      4 inch stroke 3 inch bore all forged
      Total seal gapless ring
      clevite bearings
      compression roughly 10.5-10.9
      Heads are Dart, PRC,or AFr Heads
      Intake is either BBk or Weind aluminum intake
      motor will be N/a
      this is in a 65 chevelle so if you need any other info let me know.
      Thank
      Randy

      DEMONIC OBSIDIAN
      1965 Chevelle lt1 gen v /T56 project.


    2. #2
      Join Date
      Aug 2004
      Location
      Dunwoody, GA
      Posts
      4,983
      Country Flag: United States
      You should consider the GM L92 heads/intake setup and the Trick Flows as well.

      For a 402 I would not go with anything smaller than the 233/239 cam. I'd actually go bigger. Say 236/240 on a 112 or 110 even. It'll be lopey but it'll make very good power. Keep in mind all the specs you just listed from both comp and TSP are for 346 cu in engines.

      You'll definitely need long tube headers 1-3/4" minimum primary tubes and I'd go with a FAST 90/90 ported if you do not choose the L92 setup. You read that right Goatman and Tony, I suggested a FAST setup It's needed with this combo I feel.
      Trey

      "The early bird may get the worm, but the second mouse gets the cheese."
      ~ Jon Hammond

      1979 WS6 Trans Am stock LT1/T56 drive train out of my Formula. BMW M-parallel rims. C5/C6 brakes

      build thread https://www.pro-touring.com/showthre...ghlight=begins

    3. #3
      Join Date
      Jun 2006
      Location
      TX
      Posts
      177
      budget?

      all those cams you listed are rather small for a 402. i wouldnt go any smaller than TSP MS3. i ran the ms3 on my 346 and loved it. for heads go with the AFR 205s.

      check out this thread for tons of great info.
      http://www.ls1tech.com/forums/showthread.php?t=732392

    4. #4
      Join Date
      May 2007
      Location
      Eugene Oregon
      Posts
      293
      Country Flag: United States
      so yo are saying go bigger what about clearence problems and stuff I thought the cams I chose were already big
      DEMONIC OBSIDIAN
      1965 Chevelle lt1 gen v /T56 project.

    5. #5
      Join Date
      Dec 2004
      Location
      Morehead City, NC
      Posts
      929
      Country Flag: United States
      I just put a Livernois stage 2 cam in my LS2. Stock 6.0 with flat tops L92 heads. The cam is 232/236 @ .050 590/601 W/ 114 lsa. No clearance issues. Got .100 PTV on intake and .145 on exhaust. You can go bigger than what you listed.
      Mike Holleman

    6. #6
      Join Date
      Feb 2007
      Posts
      199
      futral has some nice cams.check out the f-15 cam

    7. #7
      Join Date
      May 2007
      Location
      Eugene Oregon
      Posts
      293
      Country Flag: United States
      well my car is going to be protouring not racing so i want a nice lope some nice power and some decent milage.
      DEMONIC OBSIDIAN
      1965 Chevelle lt1 gen v /T56 project.

    8. #8
      Join Date
      Sep 2004
      Location
      Santa Barbara, Ca
      Posts
      1,174
      Quote Originally Posted by jonnyc
      futral has some nice cams.check out the f-15 cam

      I would suggest not doing business with Futral. I ordered a cam, pushrods and timing chain from them last year. After several months, I still had not recieved my parts, and nobody would return my calls or e-mails. Horrible customer service. Eventually I got my money back, but it was like pulling teeth.

      Also, their cams are ground by Cam Dynamics. Not a huge deal, but I've always been a Comp Cams guy myself.

      Andy

    9. #9
      Join Date
      Aug 2004
      Location
      Dunwoody, GA
      Posts
      4,983
      Country Flag: United States
      Of the cams you chose only the 233/239 would be considered big, but again that's big for a 346 not a 402. Now-a-days that 233/239 isn't even considered big for a 346 anymore.

      You have to keep in mind that a 402 needs more air. It gets more air by having larger runner volume heads and have the cam shaft duration longer. So be careful when reading peoples write ups and what they say to specifically use. That write up on LS1tech is good, but the specifics do not apply to you. So do not use AFR 205s like the author did. The basics such as valve timing and exhaust and the free mods section do apply to you and a 402 as it will use the same principals as does any other motor.

      AFR 225s have a 225cc runner volume. GM's L92 have a 260CC runner volume. The L92s are very similar to what is on the LS7. The L76 intake is required with the L92 heads.

      Personally, I would build it using L92/L76 intake. Have the exhaust ports ported and smoothed. I'd go with stepped headers if you can find a pair that will fit. I'd then go with a cam in the range I mentioned. That will give you good all around power. The tighter LSA will still give you good low end torque for pulling out of the corners. If you think you want to go on the more aggressive side of street manners, go with a 240/244 cam on a 112 LSA. This will make a good all around combo that's nothing exotic. If you want unheard of numbers out of you 402, int he same manner as the 500rwhp 347 in that link, either get out your check book and call someone like Wegner, or start learning cam theory and become a mastermind at understanding these engines. Then you can build it yourself and save money. Me, I can't wait that long nor do I have a check book, so I'll build something good and call it done.
      Trey

      "The early bird may get the worm, but the second mouse gets the cheese."
      ~ Jon Hammond

      1979 WS6 Trans Am stock LT1/T56 drive train out of my Formula. BMW M-parallel rims. C5/C6 brakes

      build thread https://www.pro-touring.com/showthre...ghlight=begins

    10. #10
      Join Date
      May 2007
      Location
      Eugene Oregon
      Posts
      293
      Country Flag: United States
      So who make an aftermark LQ9 head or do I need a stock one then have work done to it. also then What big cam can I use for a stroker I have no Idea on what lift I can do.
      DEMONIC OBSIDIAN
      1965 Chevelle lt1 gen v /T56 project.




    Advertise on Pro-Touring.com