Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Page 1 of 3 1 2 3 LastLast
    Results 1 to 20 of 44
    1. #1
      Join Date
      Mar 2005
      Location
      Miamisburg, Oh
      Posts
      2,396

      Front sub-frame to Firewall bracing

      Would it be worthwhile for me to put some bracing from the firewall to the front subframe (with plates of course) if I did NOT have any roll-bar in the car?
      The car has DSE SFC's and a DSE mini-tub.

      The basic idea is in this picture and I would *like* to do it unless it's a waste without the full cage. I thought I had saved other pic's too but I can't find them.

      Last edited by BA.; 06-22-2009 at 10:48 AM.
      69 RS
      LS7, T56 and other cool stuff
      Back on track in late 2020!
      Build Thread


    2. #2
      Join Date
      Aug 2004
      Location
      San Antonio, Tx
      Posts
      1,193
      i did on my car, i'm nor sure if it will do a lot of good with solid bushing and DSE frame ties but it can't hurt anything either.
      Instagram: CamaroAJ

    3. #3
      Join Date
      Jan 2003
      Location
      Arizona
      Posts
      5,394
      Country Flag: United States
      W/o a roll cage I don't know if it helps, but I know it doesn't hurt. Attach to the corner of the cowl rather than the face of the firewall for strength. In pix, note the 90 degree angle-steel brace that the down bar is welded to. Be wary of clearance to hood hinges, brake boosters, etc.

      http://homepage.mac.com/streetfytr/R...toAlbum43.html
      ________________
      Steve Chryssos

    4. #4
      Join Date
      Aug 2004
      Location
      San Antonio, Tx
      Posts
      1,193
      Quote Originally Posted by streetfytr68
      Be wary of clearance to hood hinges, brake boosters, etc.
      i forgot to say that in my post. i put the fenders and inner fenders on when i fit my bars, also i'm not using a stock brake set-up so that gave me more clearance.
      Instagram: CamaroAJ

    5. #5
      Join Date
      Dec 2004
      Posts
      441
      Country Flag: United States
      One of the magazines did a tech article a few months back on building a set of bars for the first gen. Chevy Hi Performance maybe?

    6. #6
      Join Date
      Jun 2005
      Location
      Greenwood, SC
      Posts
      2,314
      a different design with a similar purpose is pretty common among (non-stock) second gen builders...these tie in to the lip on the top of the firewall, the corners where the fenders mount, and the UCA mounting points. Maybe you could fab up something similar?

      I know that before I had these, with solid body mounts, I got a lot of squeaky and creaky action from my front subframe. Putting these on made that go away...hardly a scientific analysis, but still pretty strong evidence that it did in fact make a difference.


    7. #7
      Join Date
      Jan 2003
      Location
      Arizona
      Posts
      5,394
      Country Flag: United States
      Those look like a good idea. They work?
      ________________
      Steve Chryssos

    8. #8
      Join Date
      Dec 2004
      Posts
      441
      Country Flag: United States
      Quote Originally Posted by bretcopsey
      One of the magazines did a tech article a few months back on building a set of bars for the first gen. Chevy Hi Performance maybe?
      After some online searching, the best I could find was an eBay sale

      http://cgi.ebay.com/CHEVY-HIGH-PERFO...QQcmdZViewItem


      3) Firewall to frame supports for a 1st Gen Camaro

      Regardless, it was a tech article showing how to make some from scratch. I believe the were bolt in as well...



    9. #9
      Join Date
      Jun 2005
      Location
      Greenwood, SC
      Posts
      2,314
      Quote Originally Posted by streetfytr68
      Those look like a good idea. They work?
      Haven't quite completed my entire chassis' structural analysis yet but the seat-o-pants-o-meter says yes!

    10. #10
      Join Date
      Mar 2002
      Location
      Redwood City, CA
      Posts
      1,895,413,640
      Country Flag: United States
      Quote Originally Posted by streetfytr68
      Those look like a good idea. They work?
      They were originally developed, or so I hear, by Herb Adams. Most of what he built worked. I'll be ordering a set for my car one of these days too.
      Allen Ortega
      Meanstreets Performance Fabrication

      ---------------------------------------

      Vegetarians are the reason for global warming

    11. #11
      Join Date
      May 2000
      Posts
      4,151
      Country Flag: United States
      Herb Adams use to sell such a thing.

    12. #12
      Join Date
      Mar 2005
      Location
      Miamisburg, Oh
      Posts
      2,396
      Bret: Thanks, I picked that mag up. It may help.

      Formula: I like those. Do they use the UCA bolts and Fender mount bolts, or, do they weld into those area's? It was hard for me to tell in the pic. Got any more?

      Steve: When you say "attach to the corner of the cowl instead of the face of the firewall". ......I'm feelin' a bit dense. lol.
      Do you mean just move as far outboard on the firewall so that I'm in that stronger area, OR, do you mean a different spot?

      PS. I like Herb. He's da bomb. ;)

    13. #13
      Join Date
      Aug 2004
      Location
      Pittsburgh, PA
      Posts
      316
      Quote Originally Posted by BA.
      Formula: I like those. Do they use the UCA bolts and Fender mount bolts, or, do they weld into those area's? It was hard for me to tell in the pic. Got any more?
      I run them on my car as well. They are bolt in. The leg that goes to the top of the firewall has two holes drilled down through the lip that protrudes out over the top of the fire wall. The lower end of it attaches to the front crossshaft bolt. The leg that runs out towards the fender bolts into the fender bolt that points in towards the passenger compartment.

      Shane

    14. #14
      Join Date
      Jun 2005
      Location
      Greenwood, SC
      Posts
      2,314
      yup, they're entirely bolton. drill two small holes on each side of the top of the firewall and you're done.

      I'll try and snap a few pics of the ones in my engine bay tomorrow, if I get the chance, to show more detail.

    15. #15
      Join Date
      Jan 2003
      Location
      Arizona
      Posts
      5,394
      Country Flag: United States
      Quote Originally Posted by BA.
      .....Steve: When you say "attach to the corner of the cowl instead of the face of the firewall". ......I'm feelin' a bit dense. lol.
      Do you mean just move as far outboard on the firewall so that I'm in that stronger area, OR, do you mean a different spot?

      PS. I like Herb. He's da bomb. ;)
      Todd and crew at TLT Racetek built corner braces that secure to both the face (firewal) and top (cowl) then welded the down bar to that.
      ________________
      Steve Chryssos

    16. #16
      Join Date
      Aug 2004
      Posts
      830
      Any one afraid of being speared by one of those braces in a bad wreck?

      to me the only safe way to pull that off is to integrate them into a cage structure...

    17. #17
      Join Date
      Aug 2004
      Location
      Ontario, Canada
      Posts
      2,314
      Country Flag: Canada
      Quote Originally Posted by RobM
      Any one afraid of being speared by one of those braces in a bad wreck?

      to me the only safe way to pull that off is to integrate them into a cage structure...
      Having owned a '75 I would say that an accident would have to be very severe for those braces to make it into the passenger compartment. In which case you would be toast anyways.
      There is quite a bit of distance between where the braces go and the driver or passenger. The distance in a first gen is only slightly shorter.
      Ken
      If there is a hard way to do something, I'll find it!
      My other car is a Vega.

    18. #18
      Join Date
      Aug 2004
      Location
      NY
      Posts
      1,070
      If your car is stripped down of its front sheetmetal put a jack under the front crossmember and jack it up. If you have a dial indicator you can get real movement numbers otherwise use what you got. You will be surprised how much movement is supported by the front sheetmetal. The forward struts attched to the body help eliminate just about all deflection.


      I did the above experiment a couple years ago on a 1st Gen Bird with weld in DSE connectors. I hid forward braces and it was night and day. If you mount on a 3/16 pad you will have no problems. Try and mount over seam as that is where all the cowl panels meet and strongest section.

    19. #19
      Join Date
      Aug 2004
      Posts
      830
      i supose if you dont have a cage and safety equipment, you shouldnt be going fast enough to stuff the front end that hard and survive any way.

    20. #20
      Join Date
      Apr 2002
      Posts
      777
      Country Flag: United States
      Quote Originally Posted by BRIAN
      If your car is stripped down of its front sheetmetal put a jack under the front crossmember and jack it up. If you have a dial indicator you can get real movement numbers otherwise use what you got. You will be surprised how much movement is supported by the front sheetmetal. The forward struts attched to the body help eliminate just about all deflection.


      I did the above experiment a couple years ago on a 1st Gen Bird with weld in DSE connectors. I hid forward braces and it was night and day. If you mount on a 3/16 pad you will have no problems. Try and mount over seam as that is where all the cowl panels meet and strongest section.

      If the body bushings are wore you can measure it with a tape measure. I've seen it on Nova's all the time.

      --JMarsa

    Page 1 of 3 1 2 3 LastLast



    Advertise on Pro-Touring.com