Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Results 1 to 15 of 15

    Thread: tire wear

    1. #1
      Join Date
      Jun 2006
      Posts
      42

      tire wear

      on my 68 firebird , I have 1 degre negative camber , 3.5 degre positive caster and 1/8 toe in . My 245-45-17 tires have approximatively 3000 miles and I begin to see light wear on the outside . I thought I would see the wear appear on the inside first ? Is it normal ?



    2. #2
      Join Date
      Dec 2004
      Location
      Bothell, WA
      Posts
      225
      That isn't a ton of negative camber..well not for what I am used to seeing at least. Are you doing a lot of hard cornering?
      Travis

      '67 Mustang 289 {Ssssssold...?}
      '71 Ruster 340 {Project}

    3. #3
      Join Date
      Nov 2002
      Location
      state of confusion
      Posts
      1,499
      Country Flag: United States
      Are the control arm bushings original or have they been replaced? If so, how long ago?

      Crappy bushings can give you one reading when you align it (car at rest) but quite a different value when you're actually cornering it.


      Norm
      '08 GT coupe, 5M, suspension unstockish (the occasional track toy)
      '19 WRX, Turbo-H4/6M (the family sedan . . . seriously)
      Gone but not forgotten dep't:
      '01 Maxima 20AE 5M, '10 LGT 6M, '95 626, V6/5M; '79 Malibu, V8/4M-5M; '87 Maxima, V6/5M; '72 Pinto, I4/4M; '64 Dodge V8/3A

    4. #4
      Join Date
      Apr 2001
      Location
      Central CA USA
      Posts
      6,114
      Country Flag: United States
      With the extra neg camber you have, you should try some toe out, perhaps zero to 1 1/6" out . The tires leaning inward at the top create a "camber thrust" pushing against each other, this pulls the tires into a toe-in position, they are each pushing inward putting load on the outside edges of the tread.

      The chart below shows a 35 lb side thrust (per side) generated by a 1 deg neg camber with 1000 lbs vertical loading.
      67 Camaro RS that will be faster than anything Mary owns.

    5. #5
      Join Date
      Oct 2003
      Location
      Arvada, Co
      Posts
      2,119
      Country Flag: United States
      Quote Originally Posted by David Pozzi
      With the extra neg camber you have, you should try some toe out, perhaps zero to 1 1/6" out . The tires leaning inward at the top create a "camber thrust" pushing against each other, this pulls the tires into a toe-in position, they are each pushing inward putting load on the outside edges of the tread.

      The chart below shows a 35 lb side thrust (per side) generated by a 1 deg neg camber with 1000 lbs vertical loading.
      1 1/6 out David???? Do you mean 1/16 out?
      Brian


      I have an unlimited budget. That bad part is I have already used it up.

    6. #6
      Join Date
      Aug 2004
      Location
      Boston MA
      Posts
      686
      No David was right, 1 1/6 toe out. He's trying to get his camaro to turn in like the Lola.
      1967 #s RS

    7. #7
      Join Date
      Jul 2002
      Location
      Mesquite, TX
      Posts
      4,941
      Country Flag: United States
      35 pounds for 1 degree - the chart is for Bias Ply; does that number hold true for radials as well?

    8. #8
      Join Date
      Jun 2006
      Posts
      42
      tanks very much for your input .
      for answer to DusterRT , I dont make competition and except some time , I dont hard cornering . for Norm Peterson , yes my car haved aligned whit polygraphite bushing and sometime after I installed rubber bushing on lower control arm ( I know the guys here like the del-a lum but in quebec the road are often bad and with my experience I prefer my car whit rubber on lca for my applcation ) . this change have possibely accentuate the camber . finaly my car need to return at alignement shop . I have intention to ajust at .5 negative camber and try 0 or 1/16 to in . what do you think ? derekf have a good question , someone have reponse ?

    9. #9
      Join Date
      Dec 2004
      Location
      Bothell, WA
      Posts
      225
      I'd try zero toe first. Toe will wear your tires more than a smidge of negative camber alone.

      And did you mean that you changed the bushings after the alignment was done? That will throw things off for sure..if that's the case, you'll likely need a full alignment rather than a toe change.
      Travis

      '67 Mustang 289 {Ssssssold...?}
      '71 Ruster 340 {Project}

    10. #10
      Join Date
      Aug 2005
      Location
      Hamilton, NJ
      Posts
      4,319
      Country Flag: United States
      1 1\6"? Wow, I would think that car would be vary darty (which may be good on the track, I don't know). Does that change with tie rod location (front vs rear aka 1st gen vs 2nd gen)?
      Scott from NJ.

      Vent Windows Forever! ...

      Feather-light suspension, Konis just couldn't hold
      I'm so glad I took a look inside your showroom doors

    11. #11
      Join Date
      Aug 2004
      Location
      Red Deer, Alberta, Canada
      Posts
      1,364
      Country Flag: Canada
      Quote Originally Posted by BonzoHansen
      1 1\6"? Wow, I would think that car would be vary darty (which may be good on the track, I don't know). Does that change with tie rod location (front vs rear aka 1st gen vs 2nd gen)?
      1 1/6 isn't even a measurement haha.

      -Matt
      Matt
      72 Chevelle 370ci, 76mm single turbo, TKX, Speedtech Track Time, Millerbuilt Strange full floater 9", Brembo brakes, BC Forged 18x11s with 315s square
      Instagram: Cst_koon

    12. #12
      Join Date
      Apr 2006
      Posts
      23

      Darty??

      My thoughts are that the wear on one side of the tire is telling you they are not happy going down the road with the present toe settings. As the vehicle pitches it's weight from side, it probably is a little darty now(may be too small to notice)

      If changing the toe out a little evens the wear to both sides of the tyre(Change front to back after the toe change so as you get a fresh canvas so to speak) then the car should be less darty.

      The reason for changing the tyres is because even if you change the settings the tyres will continue to wear with the pattern they currently show.

      Remember everything is a compromise.

      (How'd I go David Pozzi??)
      It's hard to be sincere with a poor memory

    13. #13
      Join Date
      Apr 2001
      Location
      Central CA USA
      Posts
      6,114
      Country Flag: United States
      Oops! 1/16"
      A published rule of thumb is .1 deg toe out each side per 1 deg of neg camber, to compensate for camber thrust. That's 3/16" toe out per wheel on a 25" tall tire! So 1/16" total is very conservative.
      Last edited by David Pozzi; 07-21-2006 at 06:36 PM.
      67 Camaro RS that will be faster than anything Mary owns.

    14. #14
      Join Date
      Nov 2002
      Location
      state of confusion
      Posts
      1,499
      Country Flag: United States
      And I was perfectly willing to think you meant one and one-sixth millimeters . . .
      '08 GT coupe, 5M, suspension unstockish (the occasional track toy)
      '19 WRX, Turbo-H4/6M (the family sedan . . . seriously)
      Gone but not forgotten dep't:
      '01 Maxima 20AE 5M, '10 LGT 6M, '95 626, V6/5M; '79 Malibu, V8/4M-5M; '87 Maxima, V6/5M; '72 Pinto, I4/4M; '64 Dodge V8/3A

    15. #15
      Join Date
      Dec 2004
      Location
      Bothell, WA
      Posts
      225
      Quote Originally Posted by protour_chevelle
      1 1/6 isn't even a measurement haha.

      -Matt
      Sure it is! Just divide an inch into 6 parts.

      Reminds me of a time I was working on our Formula SAE car attempting to roughly set the toe off the brake rotors with a tape measure. I was measuring and someone else was writing it down, and in the midst of wrestling with the tape, I blurted out, "OK, that's about thirty four and, uhmm..ten and a half sixteenths." Raised a couple eyebrows, lol.
      Travis

      '67 Mustang 289 {Ssssssold...?}
      '71 Ruster 340 {Project}




    Advertise on Pro-Touring.com