Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Page 1 of 3 1 2 3 LastLast
    Results 1 to 20 of 42
    1. #1
      Join Date
      Mar 2006
      Location
      So cal
      Posts
      249

      Nova Front End Lowering Question ...... Dropped Spindles

      I am working towards getting the front end on my 72 down about 3 inches? right now it is about 3 maybe 4 inches from the top of the 17 inch tire to the bottom of the fender lip.

      I have looked into several options one being the Airride set up but it is not in the budget right now.

      So what dropped spindles and springs are you guy's using on your Nova's for this year? what seems to work best,I see some dropped spindles that give the stock set up and some that kick the wheel out an 1/8 inch or so?

      Any feedback and info on Dropped Spindles/Springs for this year would be helpfull.

      Thanks



    2. #2
      Join Date
      Oct 2003
      Location
      Arvada, Co
      Posts
      2,119
      Country Flag: United States
      Quote Originally Posted by NOVA
      I am working towards getting the front end on my 72 down about 3 inches? right now it is about 3 maybe 4 inches from the top of the 17 inch tire to the bottom of the fender lip.

      So what dropped spindles and springs are you guy's using on your Nova's for this year? what seems to work best,I see some dropped spindles that give the stock set up and some that kick the wheel out an 1/8 inch or so?

      Any feedback and info on Dropped Spindles/Springs for this year would be helpfull.

      Thanks
      Dropped spindles are the last thing you want to do to lower your Nova. A 72 has the same front suspension as the first gen Camaros. You should do a search and you will find all the information you need to make an informed choice.
      Brian


      I have an unlimited budget. That bad part is I have already used it up.

    3. #3
      Join Date
      Oct 2004
      Location
      Delaware, OH
      Posts
      1,379
      You'd probably be happier utilizing drop springs (DSE, Hotchkis) instead of drop spindles.

    4. #4
      Join Date
      May 2000
      Posts
      4,151
      Country Flag: United States

    5. #5
      Join Date
      Mar 2006
      Location
      So cal
      Posts
      249
      Interesting,is this just a Camaro / Nova thing? I put a set of dropped spindles on my 55 Chevy with no problems it seems to ride good,I have yet to put on a set of dropped springs thats next for that car too but I have no problems with the dropped spindle ride so far?


      Why do you guy's not reccommend using dropped spindles on the Nova? is it a geometry thing? (trying to learn something here not second guessing anyone)appreciate the info,I guess I am now learning the Pro Touring thing!

    6. #6
      Join Date
      Mar 2002
      Location
      Redwood City, CA
      Posts
      1,895,413,640
      Country Flag: United States
      It is a geometry thing. The spindles won't affect the ride at all, but the handling will be noticeable.
      Allen Ortega
      Meanstreets Performance Fabrication

      ---------------------------------------

      Vegetarians are the reason for global warming

    7. #7
      Join Date
      Mar 2006
      Location
      So cal
      Posts
      249
      Well I guess I'll go with springs for Now!?Thanx

    8. #8
      Join Date
      Oct 2003
      Location
      Arvada, Co
      Posts
      2,119
      Country Flag: United States
      Nova, yes springs are the best way to go. If you use a drop spindle and wider rims you will hit the outer tie rod with the rim. You will still have that awful geometry. A lowering spring puts the upper control arm in a better position for better geometry.
      Brian


      I have an unlimited budget. That bad part is I have already used it up.

    9. #9
      Join Date
      Dec 2003
      Location
      lost
      Posts
      2,607
      Just curious Camaro guys...what geometry changes occur by running drop spindles, since the none of the x,y,z positions change other than all being dropped an equal amount, how is there affect on handling-adverse or otherwise. I understand the steer arm to wheel concern but geometry issues...no.

    10. #10
      Join Date
      Mar 2006
      Location
      So cal
      Posts
      249
      Quote Originally Posted by dennis68
      Just curious Camaro guys...what geometry changes occur by running drop spindles, since none of the x,y,z positions change other than all being dropped an equal amount, how is there affect on handling-adverse or otherwise. I understand the steer arm to wheel concern but geometry issues...no.
      This is why I asked about dropped spindles, as I was told basically what dennis68 is saying?

    11. #11
      Join Date
      Nov 2005
      Location
      Houston,TX
      Posts
      1,159
      Country Flag: United States
      Im w/ u NOVA. I was always under the impression Spindles were the way to go. I guess its comes down to what your really looking for from the setup. I am definitely after a smooth ride and dont want my 71' to ride like a freakin chicken wagon goin down the road. Do the Hotchkis, DSE, Etc springs really ride that rough over what a spindle drop does on these cars? And does the drop spindle really hurt handling and suspension geometry that much or is that it just doesnt improve anything over stock?
      71' Nova - LY6, T56

    12. #12
      Join Date
      Oct 2003
      Location
      Arvada, Co
      Posts
      2,119
      Country Flag: United States
      There is zero geometry change with a drop spindle. Well check that, there is a COG change and that is it, but not the RCH. The camber curve is terrible. You can have positive camber in bump. Now add body roll to that and it only gets worse. Since you did not take my advise on the seach here it is: https://www.pro-touring.com/forum/showthread.php?t=209

      Dennis, I hope my memory is right here, it has to do with the angular relationship between the UCA and LCA. When you use a drop spindle the LCA remains angled up towards the CL while the UCA is at a steeper angle up towards the CL. When the suspension goes into bump the UCA curve is greater than the LCA. So it pushes the top of the spindle out faster than the lower and thus causes a positive trend in bump. It trends positive until around 2" bump and then starts to trend negitive as the UCA moves past its apex. Keep in mind the trend is the same with whatever static alignment you have. It is even worse for droop as it trends negitive all the way. Now when you lower with 2" drop springs it brings the LCA pretty close to level with the ground and the UCA is just above its apex. With that you get negitive camber gain in bump from the get go because the UCA pulls the top of the spindle in faster than the LCA pulls in the bottom. Now in droop it will trend positive for around .5" of travel before it starts to go negitive again.
      Brian


      I have an unlimited budget. That bad part is I have already used it up.

    13. #13
      Join Date
      Dec 2003
      Location
      lost
      Posts
      2,607
      OK, so the intent of the post was not to relay that dropped spindles change geometry for the worse, simply that they don't do anything to help the already poor geometry. Using drop springs will also not do very much for the poor geometry either as the amount of drop required to get the UCA running downhill is quite substantial, it also requires running the LCA downhill as well which doesn't help the roll center or lateral movement of said RC much. I think a combination of spindle, spring and "G" mod would actually place the x,y,z coordinates in a favorable position though this is purely speculation as I don't even have an "F" body to play with.

      A side note that the new, much anticipated AFX spindle does much the same thing as just suggested by moving the pin up almost an inch and increasing the height to eliminate the need for the “G” mod. A much easier albeit more expensive way to accomplish the same thing.

    14. #14
      Join Date
      Apr 2001
      Location
      Central CA USA
      Posts
      6,114
      Country Flag: United States
      I'm assuming since this is a Pro-Touring site and PT cars typically have wide tires and wheels up front, and handling is important to the owner..

      The Camaro/Nova suspension has a poor camber curve, lowering the stock suspension put's the upper arm at a better angle since it's shorter than the lower arm, you get into a better part of the "curve". The lower arm isn't ideal, but what else are you going to do?

      Installing a drop spindle leaves the suspension in the poor stock condition, in addition the drop spindles have to leave the outer tie rod end 2" lower in relation to the tire/wheel, usually on a pro-touring car with wide wheels/tires, the tie rod hits the tire sidewall. With just shorter coils and stock spindles, the tie rod may fit inside the rim if the wheels are 17" or more. Camaros up to 1969, and Nova up to 1974 have three lengths of outer steering arms depending on the factory steering ratio. The shorter arms are better for wheel clearance.

      Heidt has taller drop spindles that improve the geometry but the tie rod problem is still there.

      See pic here:
      Last edited by David Pozzi; 03-17-2006 at 06:05 PM.
      67 Camaro RS that will be faster than anything Mary owns.

    15. #15
      Join Date
      Mar 2006
      Location
      So cal
      Posts
      249
      See pic here:
      https://www.pro-touring.com/forum/at...5&d=1120332375[/quote]


      Thanks everyone and good pic david pozzi,springs for now!
      72 Nova

    16. #16
      Join Date
      Feb 2006
      Location
      s.f. east bay california
      Posts
      209

      mounting position

      Would it be posible to mount the stearing tie rod end on the top side of the spindle mount.
      Dog will Hunt

    17. #17
      Join Date
      Oct 2003
      Location
      Arvada, Co
      Posts
      2,119
      Country Flag: United States
      Quote Originally Posted by trackrat79
      Would it be posible to mount the stearing tie rod end on the top side of the spindle mount.
      On a first gen, no. It would increase bumpsteer.
      Brian


      I have an unlimited budget. That bad part is I have already used it up.

    18. #18
      Join Date
      Feb 2006
      Location
      SoCal
      Posts
      1,622
      Would you be able to shorten the UCA to pull the spindle back in and what would be the trade off if you did this? Is this why a taller spindle is better so that the UCA angle is not so steep which in turn affords a better FVSA?
      From what I have learned so far, it seems that the best setup is for the LCA to be level to the ground and the UCA to have a slight downward slope so that in bump the the LCA and the UCA work together to effect as little as possible the static camber that the car is setup with. Is this correct?
      '66 Chevy II - The "NEW" '69 Camaro!

      ***Under Construction***

      Build Update Link:

      https://www.pro-touring.com/forum/sh...ad.php?t=17108

    19. #19
      Join Date
      Sep 2004
      Location
      savannah,ga
      Posts
      862
      Country Flag: United States
      There are several ways to skin this cat. To 'lower the front end' you can also use shorter front subframe bushings and have no change in front suspension at all. Short springs, short bushings and the G-mod would seem to be effective from a performance and a cost perspective.

    20. #20
      Join Date
      May 2002
      Location
      Northern California
      Posts
      10,716
      Country Flag: United States
      im using a tall ATS spindle and a chopped spring.

      I'd advise against lowered body bushings as that simple change adds a lot of work to make it happen right.
      MrQuick ΜΟΛ'ΩΝ ΛΑΒ'Ε


    Page 1 of 3 1 2 3 LastLast



    Advertise on Pro-Touring.com