Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Results 1 to 5 of 5

    Hybrid View

    1. #1
      Join Date
      Feb 2011
      Posts
      51

      bending fuel line

      anyone have any tips/advice on bending fuel lines?

      trying to run 1/2" feed with copper/nickel tube. i haven't had any luck with the tube wanting to collapse when bending.



    2. #2
      Join Date
      Nov 2018
      Posts
      1,004
      Country Flag: United States
      Way back inna dawn 'o time, I used to use my knee to bend tubing. Bend it over a bit, shift, bend a bit, shift back, over and over until either the tube was bent or my knee quit working. It would take forever.
      __________________________________________________ __________________________________________________ ________
      I have a tube bender like this now. It works OK, but it does take some practice to bend lines accurately without bending. And, speed is not your friend here. Go too fast and the line will try to collapse. Slow, smooth and deliberate movement is the way forward, along with practice tubing. Don't worry about wasting the practice stuff, just toss it in the random bits bin. It'll still be good when you need a short piece or some scrap tubing for something. It's not going to be machine-bent precise either. It's fine when building a driver, but I'd not use it if I were building a showcar.

      __________________________________________________ __________________________________________________ ________
      One like this, with dedicated dies that spin and also come together all the way around the tube would work better. I rarely need to bend tubing but if I did it a lot I'd likely have a set like this.

      __________________________________________________ __________________________________________________ ________
      My dad, may he rest in peace, said that back in the 1950s they used to get mandrel bends on exhaust pipes by packing the pipe with sand and welding the ends over before bending. After they bent the tube, they cut the end off and knocked the sand loose. The sand would shift with the bender, but would not allow the tube to collapse. You could probably do something similar with very fine sand.
      2021 Durango R/T
      2005 Dakota beater
      2003 Dakota project-o-mobile

    3. #3
      Join Date
      Nov 2006
      Location
      Mountain Springs, Texas
      Posts
      4,880
      Country Flag: United States
      1/2 Nicop will need a fairly large bend radius. Try to find a decent used dedicated 1/2 bender. Something like this
      https://www.ebay.com/itm/33657969289...3ABFBM6oPK8tRn
      1969 Camaro - LSA 6L90E AME sub/IRS
      1957 Buick Estate Wagon
      1959 El Camino - Ironworks frame
      1956 Cameo - full C5 suspension/drivetrain
      1959 Apache Fleetside

    4. #4
      Join Date
      Aug 2007
      Posts
      744
      I like nicopp and use it on all my LS swaps. Not so much for fuel but for brake lines. It flares like butter. Bending wise just to test a piece buy a 2? foot length from like Oreilly's and see how it bends by hand.
      In lieu of hard line have you considered -6 or -8 SS flex line instead of hard line?

    5. #5
      Join Date
      Feb 2011
      Posts
      51
      Quote Originally Posted by 79 Camaro View Post
      I like nicopp and use it on all my LS swaps. Not so much for fuel but for brake lines. It flares like butter. Bending wise just to test a piece buy a 2? foot length from like Oreilly's and see how it bends by hand.
      In lieu of hard line have you considered -6 or -8 SS flex line instead of hard line?
      I didn't want to run the full length of the car with hose




    Advertise on Pro-Touring.com