Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Results 1 to 11 of 11
    1. #1
      Join Date
      Sep 2014
      Posts
      1
      Country Flag: Canada

      pro touring a amc

      ok I have always loved pro touring cars so I just bought my self a sweet 1967 amc rambler American 2dr coupe non post. I already got the motor and tranny figures not sure on the rear pumpkin yet love to pro tour this car but not sure where to start and whats avalible for a 67 rambler American any and all info would be great.



    2. #2
      Join Date
      Apr 2010
      Location
      Pittsburgh, PA
      Posts
      717
      I'm not sure of any AMC pro-tour specific companies or products, but I know Chassis works and AME have front and rear clips that they'll tailer to your specific needs..but they'll be abour 4-5k each end give or take
      72 buick skylark
      twin-turbo fuel injected buick 350..perhaps stroked to 370 in the works!

    3. #3
      Join Date
      Apr 2010
      Location
      Pittsburgh, PA
      Posts
      717
      ps. ive been eyeing a a 74 javelin for 3500 for sole purpose of pro-tour, but it'll take away from the buick progress :-S
      72 buick skylark
      twin-turbo fuel injected buick 350..perhaps stroked to 370 in the works!

    4. #4
      Join Date
      Feb 2012
      Location
      SW, Michigan
      Posts
      875
      Country Flag: United States
      Yes please!!!! Start a project thread if you get this going!!

    5. #5
      Join Date
      Apr 2010
      Location
      Pittsburgh, PA
      Posts
      717
      did a lil digging,
      there was a nice pro-tour javelin project on lateral -G
      http://www.lateral-g.net/forums/showthread.php4?t=26454
      this is the guy he used to make a front clip that uses C6 stuff
      also worth checking out
      scott of
      http://vintageracingandperformance.com/
      72 buick skylark
      twin-turbo fuel injected buick 350..perhaps stroked to 370 in the works!

    6. #6
      Join Date
      Sep 2009
      Location
      Gainesville,GA
      Posts
      15
      Country Flag: United States
      Control Freak in FLA makes the best front bolt in front subframe,coil-over shocks ,disc brake and rack & pinion setup. They also have 4 link rear suspension setups,but they are weld in units.

    7. #7
      Join Date
      Apr 2010
      Location
      Pittsburgh, PA
      Posts
      717
      72 buick skylark
      twin-turbo fuel injected buick 350..perhaps stroked to 370 in the works!

    8. #8
      Join Date
      Oct 2014
      Location
      Cañon City,CO
      Posts
      54
      Country Flag: United States
      You might give Open Tracker Racing a call , they have a set of roller spring perches for the control arms and may be able to modify both the upper and lowers for you.
      I have the complete roller set up on my Mustang and the feel is very nice.

    9. #9
      Join Date
      Sep 2014
      Location
      CA - High Desert
      Posts
      23
      Country Flag: United States
      I think it was Car Craft magazine did a 67 (or there abouts) rambler build about 8-10 years ago. Not exactly protouring style but pretty decent series regardless.

    10. #10
      Join Date
      Sep 2006
      Location
      Southern Indiana
      Posts
      4,709
      Country Flag: United States
      ridetech rear triangulated 4 link, Marcus at SC&C can probably whip up a set of SPC arms out of parts. Typical either an aftermarket 12 bolt or a 9in can be made to fit or even a Dana60.
      Figure a full set of ridetech double adjustable Coil overs and some judicious suspension tuning tricks and have fun. any engine from SBC to LSx can be swapped heck even a HEMI could be swapped in.
      And anything from a turbo 4 cylinder to a V6 or V8.
      Dare to be different can be fun.
      Also being an older car, its a wide open canvas.
      Lee Abel
      AFTERMARKET PERFORMANCE

      1977 Chevy Monza 2+2:Project "Cheap Trick"
      1978 C10 Long bed , On air and trailer puller
      2006 Buell Blast ,Just a bike to ride and for mileage
      1966 Caprice 4dr Sports Roof fact.327/now 350/SOON 454???? Project "II Old,,,ZERO BUDGET OR LESS CAPRICE!"

    11. #11
      Join Date
      Jul 2014
      Posts
      8
      Country Flag: United States
      I'm working on my '66 American and a '90-'92 Ranger 8.8 rear end is the same width ( I believe 56 1/8 ). Mine has 10" drum breaks, 3.73 gears with limited slip and the pinion will be off set to the passenger side a little. A lot of guys are using the explorer 8.8 rear end, it is 3 inches to wide but if you have 3 inches cut out of the drivers side, you can then use another 3 inch shorter passenger side axle getting you the correct width and a centered pinion. Most the explorer rear ends are disc brake and a lot of them have 3.73 or 4.10 gears with limited slips. Either way is a really good fit for the small bodied AMC cars, they are pretty easy to find in junk yards, and they have the correct 5 on 4 1/2 lug nut configuration.




    Advertise on Pro-Touring.com