Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Page 2 of 3 FirstFirst 1 2 3 LastLast
    Results 21 to 40 of 51

    Thread: Beach Blazer

    Hybrid View

    1. #1
      Join Date
      Aug 2010
      Location
      now In Dandridge, Tn.
      Posts
      1,301
      Country Flag: United States
      Here's a couple of shots with the motor/trans in place. Headers and exhaust is next. Last shot is of a side frame gusset at the rear of the frame. The shape and design is to solve multiple problems at once. Tie down point, rear frame slider, for those big speed bumps, and frame gusset.

      Attached Images Attached Images      


    2. #2
      Join Date
      Sep 2011
      Location
      Southern Ontario
      Posts
      640
      Country Flag: Canada
      Clean looking frame Rob, nice work.

    3. #3
      Join Date
      Aug 2010
      Location
      now In Dandridge, Tn.
      Posts
      1,301
      Country Flag: United States
      Lots of progress the last few days. The tank fab is almost done, headers fitted, and the exhaust fit is pretty much done! Even the driveshaft mock up is done. Ya buddy, my guys are kickin ass
      Attached Images Attached Images      

    4. #4
      Join Date
      Aug 2010
      Location
      now In Dandridge, Tn.
      Posts
      1,301
      Country Flag: United States
      On the body side, lots of progress here too. New Vintage Air HCD is in under the dash. The ECU is mounted, and the new EFI throttle pedal is all set. Up front the condenser is in, and the inner fender mods have started. We're on a roll!
      Have a great weekend, and many thanks to our service men and women.
      Attached Images Attached Images      

    5. #5
      Join Date
      Jun 2013
      Location
      Longview, TX
      Posts
      25
      Country Flag: United States
      Yea Rob I have one of the sq head flat tail hammers too. Its just not something you see around this kind of work everyday, but it does have its advangates.

      You guys are rocking on this one. Chassis is looking good.

    6. #6
      Join Date
      Aug 2010
      Location
      now In Dandridge, Tn.
      Posts
      1,301
      Country Flag: United States
      Today is the day. Time to put the chassis under it. So, here's the last look at it. All ready to go, brakes plumbed, gears in - 3.70 true track, rear brakes on - 13" x 4 piston, rack in place. Lookin good.
      Attached Images Attached Images      

    7. #7
      Join Date
      Aug 2010
      Location
      now In Dandridge, Tn.
      Posts
      1,301
      Country Flag: United States
      In the back we are using the fuel pump supplied from Turn-Key Engines, it's what they wanted us to use. So, we made a cool little mount for it and the pre-filter. We use a temporary strut bar to set ride height in place of the shockwave. Now that it's all together, the tank placement makes more sense, tucked up out of the way and protected.
      Attached Images Attached Images      

    8. #8
      Join Date
      Aug 2010
      Location
      now In Dandridge, Tn.
      Posts
      1,301
      Country Flag: United States
      So the chassis is in! Fits like a glove. Mike is setting it level to shim the body. The new electric-hydro is in place, and the steering lines up great. I love it when a plan comes together. (said with half a cigar and a crooked grin)
      Attached Images Attached Images        

    9. #9
      Join Date
      Jun 2013
      Location
      Longview, TX
      Posts
      25
      Country Flag: United States
      Very Nice looking chassis. What is your opinion on running flex hose from the MC to the Frame?

    10. #10
      Join Date
      Aug 2010
      Location
      now In Dandridge, Tn.
      Posts
      1,301
      Country Flag: United States
      Quote Originally Posted by aggie91 View Post
      Very Nice looking chassis. What is your opinion on running flex hose from the MC to the Frame?
      We'll run hard lines to the prop and check valves on the firewall, then flex down to the chassis. I like this method for separation/flex. Even with the new chassis and urethane mounts, things will move a little bit.

    11. #11
      Join Date
      May 2009
      Location
      Connecticut
      Posts
      409
      Country Flag: United States
      Now that is the way to run brake and fuel lines!
      Aldin
      1969 Camaro (Weapon of Choice) in the works

    12. #12
      Join Date
      Nov 2012
      Location
      Arizona
      Posts
      41
      Country Flag: United States
      That looks awesome. How close to the ground is the exhaust going to be when aired out?

      I have also been meaning to ask you what is the purpose of the tubes welded on the back of the lower control arms? I have never seen any 67-72s that utilized them. Would it affect the structure of the control arm if I cut them flush with the tube?

    13. #13
      Join Date
      Aug 2010
      Location
      now In Dandridge, Tn.
      Posts
      1,301
      Country Flag: United States
      More progress, we're blazin' though this project! Motor and trans - in. ECU harness - in. Gauge controller - in. The motor fits in nice, a bit farther back than stock. It's about 5/8" at the back of the drivers cyl head. - close, but good clearance. Now we got some plumbing and wiring to do.
      Attached Images Attached Images      

    14. #14
      Join Date
      Aug 2010
      Location
      now In Dandridge, Tn.
      Posts
      1,301
      Country Flag: United States
      When aired out and on the bump stops, the chassis is 1" off the ground, at it's lowest points. Exhaust is above that.

    15. #15
      Join Date
      Jun 2014
      Posts
      4
      Country Flag: United States
      Looking good

    16. #16
      Join Date
      Aug 2010
      Location
      now In Dandridge, Tn.
      Posts
      1,301
      Country Flag: United States
      Today we assembled the front brakes. To get what we want we use an assortment of parts. We make the Billit hub, 5 x 5", rotor adapter and caliper mount. the rotor is a 14 x 1.1 spec 37, and the caliper is a superlite 4 x 1.75" from Wilwood. These are fitted to our spindle, which is close to a late Impalla, using A3 and A6 bearings. - and, the OE style seal, not the goofy leather deal. This set up provides monster braking and is fairly light weight. At 42 lbs, it's still lighter than the OE 11" gen-2 Camaro at 51 lbs. We send out the rotors and pads for cryo prior to the install, this adds performance and lifespan, well worth the cost.
      Attached Images Attached Images    

    17. #17
      Join Date
      Aug 2010
      Location
      now In Dandridge, Tn.
      Posts
      1,301
      Country Flag: United States
      Now we have the front suspension assembled, and the brakes on. ridetech makes us custom 5" stroke Shockwaves for our WideRide IFS units. This yields over 8" of wheel travel. The side view pict shows the header fit, and the oil pan height, nice and safe.
      Attached Images Attached Images    

    18. #18
      Join Date
      Aug 2010
      Location
      now In Dandridge, Tn.
      Posts
      1,301
      Country Flag: United States
      More and more parts going in. The new Dakota Digital gauges are in, along with the Vintage Air control panel. The wiring is almost done. To clear the raised wheel wells, the OE battery tray was raised 2". Under it we mounted a Flaming River remote battery kill solenoid, nice and hidden. The fuel reg and pre-filter will mount on the firewall next to the A/C plumbing.
      Attached Images Attached Images      

    19. #19
      Join Date
      Aug 2010
      Location
      now In Dandridge, Tn.
      Posts
      1,301
      Country Flag: United States
      The brake lines are now finished and all of the valving is in place. I really like these electric-hydroboost units, lots of brakes, no P/S issues, good looks. From the top down she's starting to take shape. Can't wait for a drive in this one.
      Attached Images Attached Images    

    20. #20
      Join Date
      Oct 2004
      Posts
      90
      drool!

    Page 2 of 3 FirstFirst 1 2 3 LastLast



    Advertise on Pro-Touring.com