Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Results 1 to 5 of 5
    1. #1
      Join Date
      Apr 2005
      Location
      USA
      Posts
      4,462
      Country Flag: United States

      Small Block Chevy Oil Leak above fuel pump

      Last weekend , I went to Run to the Ole South Event in Kershaw , SC .
      My car has had a small oil leak for a long time , more like an " ooze " around the front of the engine .
      It never dripped on the ground , but enough oil was oozing to run back and make a mess of the oil pan , clutch cover and transmission .
      I thought it was either the fuel pump itself , or the front crank seal or the oil pan gasket .

      My Camaro has a GEN 1 small block Chevy .
      There are two drilled , tapped holes on the passenger side front of the block , adjacent to the fuel pump .
      The upper of these two holes is tapped deep enough to go into the oil galley where the fuel pump pushrod lives ..
      There's no pressurized oil here , but rather a gravity feed to lubricate the fuelpump pushrod and fuelpump itself .

      That upper hole has to have a 3/8" X 1/2" bolt in the hole or it will leak .

      I've had at least 30 SBC's over the years and never remember seeing this problem before ( or I just forgot ).
      Thanks to James Harrel for pointing it out at the event .

      Either way , I plugged the hole and now my powertrain is a lot cleaner ..





      Most small-blocks feature four 3/8-inch threaded holes (two per side) at the front of the block. The upper hole adjacent to the fuel pump passes into the crankcase area and if left open will allow oil to leak out from the block. Be certain to plug this hole only with a short 3/8-inch bolt (1/2-inch long). Because this hole aligns perfectly with the fuel pump’s pushrod, a longer bolt will contact and seize the pushrod during engine operation.

      Read more: http://www.chevyhiperformance.com/te...#ixzz1uNWXTKfv
      Last edited by JEFFTATE; 05-12-2012 at 04:48 PM.
      Jeff Tate
      U.S.A.
      "The best thing about participating in these events is that you get to hang out with a group of intelligent like minded people who live to achieve things in their lives. You won't find a lazy, mean, or dumb bone in their bodies." Bret Voelkel, RideTech


    2. #2
      Join Date
      Aug 2004
      Location
      Colorado
      Posts
      397
      Country Flag: United States
      That hole makes it easier to change the fuel pump. Before you remove the old pump, lightly seat a longer bolt against the push rod to prevent it from falling out while you R&R the pump.
      Brett

    3. #3
      Join Date
      Dec 2010
      Location
      Fredericksburg, VA.
      Posts
      3,164
      Country Flag: United States
      Yep, SBC 101. Those four holes are the engine mount locations for the Tri-5 Chevys.
      Steve Hayes
      "Dust Off"
      68 Camaro

      Support the RPM Act
      https://www.sema.org/rpm-faq.

    4. #4
      Join Date
      Apr 2005
      Location
      USA
      Posts
      4,462
      Country Flag: United States
      It's funny , I had forgotten all about that ...
      We learn every day , I guess .

      I hope this info may help someone someday .
      Jeff Tate
      U.S.A.
      "The best thing about participating in these events is that you get to hang out with a group of intelligent like minded people who live to achieve things in their lives. You won't find a lazy, mean, or dumb bone in their bodies." Bret Voelkel, RideTech

    5. #5
      Join Date
      Apr 2008
      Location
      Newark, OH, / Concord, NC
      Posts
      497
      And all of them don't leak either, just the one's with a little bit of core shift or hole that has been drill a little bit too deep.
      IF COMMON SENSE WAS COMMON EVERYBODY WOULD HAVE IT




    Advertise on Pro-Touring.com