Enter your username:
Do you want to login or register?
  • Forgot your password?

    Login / Register




    Results 1 to 14 of 14
    1. #1
      Join Date
      Apr 2006
      Location
      Southern California
      Posts
      212

      41565 Makes some progress....tubs fabed and back on the ground

      Finally was able to get photos figured out thanks to 454Bug! I have all of the mount tabs welded in and the wheel tubs fabed up. They are clecko'd in, in the event I have to pull them during the quarter panel install.

      Driver side tub


      Passenger side tub


      My assistant on the creeper grandpa made him!


      Back on the rollers after months in the air on a frame dolly


      Rear view, had to remove the trunk torsion springs to get the tubs in. I made a 3" wide support to weld the underside of the filler panel to the trunk hinge brace for support. It is as solid as a rock. I intend on using gas struts to hold the trunk lid open.




      Firewall is going to be smoothed as well...quarters first!


    2. #2
      Join Date
      May 2002
      Location
      Northern California
      Posts
      10,716
      Country Flag: United States
      looking good.
      MrQuick ΜΟΛ'ΩΝ ΛΑΒ'Ε


    3. #3
      Join Date
      Nov 2006
      Location
      Ma.
      Posts
      5,560
      Country Flag: United States
      Hi Nice project . What engine and trans are you using ?
      Wayne
      Wayne
      Car FINALLY home !!!!!! lol
      Project FNQUIK https://www.pro-touring.com/showthre...ghlight=FNQUIK

    4. #4
      Join Date
      Apr 2006
      Location
      Southern California
      Posts
      212
      MR Quick, thanks!

      Motown, I am going with a 383 stroker, carb'd and I have a T56-six speed going in. Need to do some fab work for the trans crossmember since nobody makes one. Goin to ATS for the clutch/brake master cylinder mount and keeping it all hyd. Have not completely decided on the front suspension, have the stock stuff all rebuilt and powder coated...looking at DSE/SCC/Global West stuff...just trying to figure it all out...

      Have a great one, like the sounds of your build.

    5. #5
      Join Date
      May 2000
      Posts
      4,151
      Country Flag: United States
      On my '66 the stock crossmember work fine with the t56, just needed to be moved a little.

      Are you narrowing the frame in the rear?

    6. #6
      Join Date
      Nov 2005
      Location
      livermore ca
      Posts
      718
      you going to have to do some work on the tunnel to if your going to fit the t56 in there.





      Quote Originally Posted by 41565 chevelle
      MR Quick, thanks!

      Motown, I am going with a 383 stroker, carb'd and I have a T56-six speed going in. Need to do some fab work for the trans crossmember since nobody makes one. Goin to ATS for the clutch/brake master cylinder mount and keeping it all hyd. Have not completely decided on the front suspension, have the stock stuff all rebuilt and powder coated...looking at DSE/SCC/Global West stuff...just trying to figure it all out...

      Have a great one, like the sounds of your build.
      https://www.pro-touring.com/forum/sh...ad.php?t=22724

      65ss chevelle
      95 lt1 LE2 heads gm847 cam, 1.6 gold sereis roller rockers,52mm tb,37lb racetronix injectors. hooker headers

      63ss nova
      350:cam headers,roller rockers.pete jackson gear drive,
      th350 shift kit 3,500 stall
      3:73

      **Drive it like you stole it!!

    7. #7
      Join Date
      Nov 2006
      Location
      Ma.
      Posts
      5,560
      Country Flag: United States
      Thanks 41565 Chevelle Looks like you'll have a sweet ride when your done .I should be getting my car back in a few weeks. Can't wait to get started.
      Wayne
      Wayne
      Car FINALLY home !!!!!! lol
      Project FNQUIK https://www.pro-touring.com/showthre...ghlight=FNQUIK

    8. #8
      Join Date
      Apr 2006
      Location
      Southern California
      Posts
      212
      LT1...the trans tunnel is huge from the T56. I cut out a ton and it is still very tight. I ended up getting a tunnel kit from Chris Alstons, working it a bit and making it fit. I will be removable by small screws to access the shifter and any electronics on the top of the trans since it is such a tight fit. I'll see if I can't dig up a pic

    9. #9
      Join Date
      Feb 2006
      Posts
      478
      If you are putting a cage in the car I wouldn't worry about it, but if your whole tunnel will be removable, I would say that would kind of weeken the shell somewhat. It just seems like the tunnel would add a great deal of stiffness to the flat floor being attached structurally to it. JM2C.

    10. #10
      Join Date
      May 2008
      Location
      Austin, Tx.
      Posts
      1,539
      Country Flag: United States
      Great project. The '64/'65 Chevelle is one car I have always dreamed of owning! Great combination. Have you thought about color, wheels, tires, and what brakes you are going to run yet?
      Ray
      FEW FRILLS, just BIG CHILLS!!!
      1972 VW Bug (427LS/T56 Magnum/9"-3.70 gears)
      18"x10-1/2" (315/30/18) Front, 18”x12" (335/30/18”) Rear
      https://www.pro-touring.com/showthre...-Lady-Bug-quot

    11. #11
      Join Date
      Apr 2006
      Location
      Southern California
      Posts
      212
      Here is a photo of the tunnel mocked up. Gearbanger...I never really thought of that, thanks for the 2C, I will get something figured out. There will not be a cage in it so back to the drawing board. I picked up a Perelli 295/40/20 to see how much room I have inside of the tubs. Can't wait for tomorrow to come so I can stick it in the wheel well and jump for joy or cry and go smaller!

      454Bug...I have a rendering done for it, colors are not %100 yet but pretty much nailed down. As for the wheels, going with a custom set from Foose most likely with Perelli's since he deals with them. Shooting for 20x10's in the rear and 19x8's up front and currently running 13" CPP brakes up front and 12" in the rear. I am going to try and get Willwood or Bear to buy into the project since I have the rendering already completed... It will be a very cool ride, I have some tricks up my sleeve that I have stored in my vacant head for several years that will be on this car. Now all I need is a bunch of overtime and time itself.


    12. #12
      Join Date
      May 2008
      Location
      Austin, Tx.
      Posts
      1,539
      Country Flag: United States
      I look forward to seeing your progress... Great project!
      Ray
      FEW FRILLS, just BIG CHILLS!!!
      1972 VW Bug (427LS/T56 Magnum/9"-3.70 gears)
      18"x10-1/2" (315/30/18) Front, 18”x12" (335/30/18”) Rear
      https://www.pro-touring.com/showthre...-Lady-Bug-quot

    13. #13
      Join Date
      Jun 2006
      Posts
      232

      Sweet

      I am assuming you built those, looks great, what gauge metal is that? That is a good looking radius pittsburgh seam, looks like someone knew what they were doing
      Project: Back in Black.
      69 Camaro LS6, T56, Wilwood Brakes, Forgeline Wheels, Moser rear w/Gbar, Ron Davis Radiator, Pioneer Nav/Stereo, Magnaflow Exhaust.

    14. #14
      Join Date
      Nov 2006
      Location
      Ma.
      Posts
      5,560
      Country Flag: United States
      Any new updates?
      Wayne
      Car FINALLY home !!!!!! lol
      Project FNQUIK https://www.pro-touring.com/showthre...ghlight=FNQUIK




    Advertise on Pro-Touring.com