Bodywork over Dp90 Questions...

[Taylor1969]

Hi Guys,

I have some of the major bodywork complete on my car and the entire thing has a coat of dp90 on it.

I am wondering if I can do the bodywork over the next month or so and then prime the whole thing. I am looking to do the tailpain this weekend, quarters next, roof, etc. and then prime the entire car.

Is it safe to leave the bodywork without covering for around a month or so?

Here are some pics for reference...

[Taylor1969]

By the way... i plan on using all metal on anything deeper than 1/8" and rage gold on the minor areas. Some of the car will be then covered in glaze and blocked out.

[hotrdblder]

as long as the car is under cover and see's no moisture then yeah you can leave the body work open, if your nervous just dust a coat of dp90 over it

[Alchemist]

A warning about DP epoxy primer. You mention there is one coat of DP sprayed on the car. One coat isn't enough! If there isn't enough DFT (dry film thickness) then it would be advisiable to remove the DP by using an orbital sander with #80 grit sandpaper to provide "mechanical adhesion" for filler work.

The DP needs to have a minimum DFT to prevent moisture bleed thru. Best to check an area by sanding. If you happen to see rust underneath the DP, then I would advise you remove it since there isn't much material anyway.

Otherwise, if there was enough DP material applied, you need to scuff the DP where you will be applying filler to aid adhesion. Also, it would be wasteful to dust on a coat of DP over the bodywork area because moisture would bleed thru it. If you plan to spray DP to prevent environmental attack on the bodywork, you must apply at least 3-4 wet coats of the DP to achieve the desired protection.

I would also suggest you acquire a product bulletin to gain more knowledge about the use and "how not to use" DP primers.

[Taylor1969]

A warning about DP epoxy primer. You mention there is one coat of DP sprayed on the car. One coat isn't enough! If there isn't enough DFT (dry film thickness) then it would be advisiable to remove the DP by using an orbital sander with #80 grit sandpaper to provide "mechanical adhesion" for filler work.

The DP needs to have a minimum DFT to prevent moisture bleed thru. Best to check an area by sanding. If you happen to see rust underneath the DP, then I would advise you remove it since there isn't much material anyway.

Otherwise, if there was enough DP material applied, you need to scuff the DP where you will be applying filler to aid adhesion. Also, it would be wasteful to dust on a coat of DP over the bodywork area because moisture would bleed thru it. If you plan to spray DP to prevent environmental attack on the bodywork, you must apply at least 3-4 wet coats of the DP to achieve the desired protection.

I would also suggest you acquire a product bulletin to gain more knowledge about the use and "how not to use" DP primers.

Sorry - I shouldn't have said one coat. I meant one application - consisting of two wet coats as reccommended by the DP90 product sheets. It takes some eblow grease to get down to metal at this point. In areas where I plan to apply filler it will be scuffed and/or taken to bare metal depending on what type of repair needs to be made. Thanks for the clarification Alchmist.

[Alchemist]

Your welcome!

When you're ready to spot prime your bodywork, be sure to thoroughly scuff all surrounding DP areas with a red scotchbrite pad, or scotchbrite the entire car if you're gonna prime the whole car/part.

[Taylor1969]

Thanks for all of your help and replies!!

I am going for the "Hot Rod" black look - I would like to keep the car like that for 1-2 years while I save up for a nice quality topcoat. If the car never sees the sun unless I am driving it and will never see rain it sounds like I should be okay without clearing.

If I spray the entire car with dp90 should i wetsand it with 500 after the final coat as you stated or will it get the chalky appearance?

For the next couple of years this is the appearance that I am after:

[Alchemist]

Taylor,

You're quite welcome! That is one nice ride!!!

Do not wetsand the DP after the final coat. If the appearance starts to chalk or blotch, that's when you'll need to sand the DP and then apply a couple of coats to "refresh" the look!

Otherwise, just spray the 3-4 passes of DP and your'e done! Don't forget to clean your spraygun thoroughly!

By the way, that rear "lip" looks fantastic - I've never seen this done to a '69 camaro before. Was this a "photoshop" pix?

[Taylor1969]

Taylor,

You're quite welcome! That is one nice ride!!!

Do not wetsand the DP after the final coat. If the appearance starts to chalk or blotch, that's when you'll need to sand the DP and then apply a couple of coats to "refresh" the look!

Otherwise, just spray the 3-4 passes of DP and your'e done! Don't forget to clean your spraygun thoroughly!

By the way, that rear "lip" looks fantastic - I've never seen this done to a '69 camaro before. Was this a "photoshop" pix?

That car is designed by fesler. Here is a link:

http://www.feslerbuilt.com/1969FeslerCamaro.htm

I fell in love with the dp90 look after seeing that car

[Alchemist]

The car is fantastic! The satin black look has always been a favorite of mine.

Thanks for the link Taylor!!