Results 1 to 12 of 12
Thread: Can I weld near gas tank???
-
03-24-2008 #1
Registered User
- Join Date
- Aug 2004
- Posts
- 362
Can I weld near gas tank???
I have some frame brackets that need to be welded near the rear end. Whats the safest way to weld near a gasoline tank in the car, maybe 8" away on the frame? No leaks in the tank and I would shield the tank and lines. Thanks
-
03-24-2008 #2
Registered User
- Join Date
- Jun 2007
- Location
- Huntington Beach, CA
- Posts
- 624
Can you drain it and let it air out with the cap off and then weld it the next day?
Better to be safe than burnt toast. I would hate to see something small turn into a disaster.Rick
-----------------------------
" Better to Be Lucky than Good "
-
03-24-2008 #3
Registered User
- Join Date
- May 2002
- Location
- Northern California
- Posts
- 10,716
The safest way is to completely remove it. Draining it isn't always the safest way as the vapors in the tank not the fluid is what is most combustable. Less fuel = more vapor.
If you must, insure there are no leaks, cap all vent lines, shield the tank/lines from welding sparks and I like to put a fan near to pump fresh air into the area so fuel vapors will not collect.MrQuick ΜΟΛ'ΩΝ ΛΑΒ'Ε
-
03-24-2008 #4
Registered User
- Join Date
- Jun 2007
- Location
- Huntington Beach, CA
- Posts
- 624
MrQuick, that's damn good info!
Letting a tank air out and assuming a tank is completely dry could create a more dangerous situation.
Rick
-----------------------------
" Better to Be Lucky than Good "
-
03-24-2008 #5
Registered User
- Join Date
- May 2002
- Location
- Northern California
- Posts
- 10,716
No problem. It all depends on how long you let it air out.
A friend of mine thought it would be safe to just empty it and go to town. It popped on him. Luckily it was a small boat tank.
Back in the day we would just fill it with water but that was gas and stick welding but I wouldn't recommend that for mig or tig.MrQuick ΜΟΛ'ΩΝ ΛΑΒ'Ε
03-24-2008 #6
Registered User
- Join Date
- Jun 2005
- Posts
- 543
You're almost better off welding near a full tank than an empty one. As other people have said, it's the fumes that are flammable.
You'd be surprised how often we get away with welding near gas at work. We often set our Ranger 8's on fire, because we weld overhead and the sparks come down and hit the gas tank on the unit.
Mathius
03-24-2008 #7
Starting The Transformation
- Join Date
- Feb 2008
- Location
- Denver NC
- Posts
- 288
#1 fill tank and sheild with a welding blanket.
#2 remove tank....
#3 TIG weld with good ventalation. But not so much you lose your sheilding gas
03-25-2008 #8
Registered User
- Join Date
- Aug 2004
- Posts
- 362
Thanks for the great tips!
03-25-2008 #9
Registered User
- Join Date
- Jun 2007
- Location
- Huntington Beach, CA
- Posts
- 624
This thread reminded me of a video clip a friend emailed me. Not too pretty. Hope he's OK.
http://www.youtube.com/watch?v=dlT9eSJZCCURick
-----------------------------
" Better to Be Lucky than Good "
03-26-2008 #10
Registered User
- Join Date
- Jul 2006
- Location
- Clinton, MS
- Posts
- 184
What A Dumb Ass!!
03-30-2008 #11
Registered User
- Join Date
- Dec 2006
- Location
- polk county,FL
- Posts
- 163
You should also purge the tank with any inert gas(argon,C25).You can't start a fire without oxygen.
03-30-2008 #12
Registered User
- Join Date
- Aug 2004
- Location
- Northern Indiana
- Posts
- 588
Personal opinion....remove the tank.
Fire! Fire!
"Champagne taste on a beer pocket book."
Reply With Quote
