1979 "Transmarrow" Mid-engine LQ9 build

[Ddkeeler]

Not quite sure what you mean by on/off type of clutch but i daily'd my 02 wrx for years with a puck clutch and lightened flywheel. Those can easily handle that type of power and once you get a good feel for the clutch i could take off smooth with no judder. Also i would look into swapping jdm sti gear sets or ppg gears into the wrx 5 speed, or sell it and buy the STI 6 speed. 1-2 are like glass and even with the original 4 cylinder its a guarantee they will shatter with anything over 300hp. the Stock 6 speeds are bullet proof but you will need to get STI knuckles/hubs since the axles are bigger. Awesome project by the way! this thing is going to turn out awesome.

Thank you all for the kind words. I’ll say I am little surprised there has not been any “what the hell are you doing to that car” sort of comments.



The on/off type engagement that is an talking about is where from a stop and there is very little easing into going. I am fine with shudders and whatever come along with it. I plan on upgrading to some better gear sets. A straight cut gear set, I believe Subaru gears makes a set so I may look into that, once it is a driver. What clutch did you run?

Until I get a hold of a large stack of cash and can afford a mendola or something this will have to suffice.

[jlcustomz]

If you've ever seen my camaro nose el camino project which is now being widebodied along with a c-7 z06 vette rear bumper, you'd know I am in no way qualified to ask what the hell are you doing---unless I see something I can advise on. Some of us need to do a little crazy to make everyone else seem more normal.
I though I posted something for you about clutches yesterday, think I forgot to hit enter. again. Anyway organic are your basic clutch compounds, then moving up into the metallic which may contain ceramic, Kevlar etc. The puck styles as Shawn mentioned are the less girlfriend friendly grippier types which is more of what you need. A good balanced unit against a good true flywheel driven properly won't shutter much. If available, which would be more pricey, twin or even triple disc units can offer way more grip without needing overly heavy pressure plate springs.

[Ddkeeler]

If you've ever seen my camaro nose el camino project which is now being widebodied along with a c-7 z06 vette rear bumper, you'd know I am in no way qualified to ask what the hell are you doing---unless I see something I can advise on. Some of us need to do a little crazy to make everyone else seem more normal.
I though I posted something for you about clutches yesterday, think I forgot to hit enter. again. Anyway organic are your basic clutch compounds, then moving up into the metallic which may contain ceramic, Kevlar etc. The puck styles as Shawn mentioned are the less girlfriend friendly grippier types which is more of what you need. A good balanced unit against a good true flywheel driven properly won't shutter much. If available, which would be more pricey, twin or even triple disc units can offer way more grip without needing overly heavy pressure plate springs.

Great info, thank you. I’ll do some digging and see what I can come up with. How accurate are the horsepower ratings that the manufacturers put on them?

I’ll check out your build, that sounds awesome. I’m just trying to step outside of the norm. I’m trying to fabricate everything that I can vs purchasing brackets, exhaust, fuel cell etc. I have a small cnc plasma table that should help me accomplish that. I figure I can cut the cost of the build drastically this way.

[Shawn0331]

Thank you all for the kind words. I’ll say I am little surprised there has not been any “what the hell are you doing to that car” sort of comments.

The on/off type engagement that is an talking about is where from a stop and there is very little easing into going. I am fine with shudders and whatever come along with it. I plan on upgrading to some better gear sets. A straight cut gear set, I believe Subaru gears makes a set so I may look into that, once it is a driver. What clutch did you run?

Until I get a hold of a large stack of cash and can afford a mendola or something this will have to suffice.

Perfect! you will be fine them with that setup. Mine was the Exedy 6 puck with their lightened fly wheel which was around 12 lbs. I dont remember the hp rating but it was waaaaay more than what my car needed.

[Ddkeeler]

Perfect! you will be fine them with that setup. Mine was the Exedy 6 puck with their lightened fly wheel which was around 12 lbs. I dont remember the hp rating but it was waaaaay more than what my car needed.

Something like this seems to fit what you’re describing. Based off the specs it should work. https://www.rallysportdirect.com/par...isc-clutch-kit