Activity Stream
-
Older Activity
-
2 Hours AgoForgeline Wheels started a thread Angel Palacio's 1956 Chevy Truck on Forgeline Forged Three Piece GA3C Wheels in Wheels & TiresThey call it "Pitch Black". Angel Palacio’s 1956 Chevrolet 3100 truck originally belonged to his father and was transformed into this modern...0 replies | 19 view(s) -
5 Hours AgoSTREETFIGHTER50 started a thread Why does BluePrint Engines say to not go synthetic until 9000 miles?? in Engine MiscellaneousA car I’m getting soon has a new (1400 mi.) 530hp LS3 crate engine from them. I always thought that after initial break-in, 500–1000 miles would be...0 replies | 35 view(s) -
5 Hours AgoBack from the dead again: I did it. And now I'm doing it for other people too. If by chance you are interested, shoot me an email at...6 replies | 8326 view(s) -
6 Hours AgoMarc, Welcome to the site. It sounds like you build some pretty cool rides. Before we get too far into this we may need to chat. Promoting...1 replies | 15 view(s) -
6 Hours AgoYes, that is non vented cap.2 replies | 31 view(s)
-
8 Hours AgoI've got a standard tank with a 350 SBC. Would appreciate any advice…2 replies | 31 view(s)
-
8 Hours AgoI've got a 68 Camaro and recently purchased the RideTech gas cap kit. My question is do I need to vent it?2 replies | 31 view(s)
-
9 Hours AgoHi, I am a restoration and custom build shop owner in Connecticut and I'm excited to be part of the forum. We started out with a general focus on...1 replies | 15 view(s)
-
9 Hours Agochevyz240 replied to a thread "Mechanix Menace": An LS7-motivated, chopped and heavily modified 1973 Datsun 240Z in Project UpdatesA little while ago, I welded in the last pieces of the hand shaped rear wheelwell corners. Today I went to https://www.autocut.se/. There, Håkan...493 replies | 359626 view(s) -
13 Hours AgoThank You Bob!58 replies | 30882 view(s) -
1 Day AgoGot my 409 Test Block in today as well as the 4L80E, going to throw some Heads on tomorrow so I can look at Header clearance, the Oil Pan as well....12 replies | 5122 view(s) -
1 Day Agohttps://bowlertransmissions.com/collections/crossmembers40 replies | 14190 view(s) -
1 Day AgoUp for sale is a new Holley EFI Terminator X Max - Part #550-931 for Gen IV 4.8/5.3/6.0 GM Truck Engines and LS2/LS3/58x Crank - 4x Cam - EV6...0 replies | 81 view(s)
-
1 Day AgoCan you please share with me where you purchased this crossmember? Thx, Pete40 replies | 14190 view(s)
-
1 Day AgoI like nicopp and use it on all my LS swaps. Not so much for fuel but for brake lines. It flares like butter. Bending wise just to test a piece buy a...3 replies | 114 view(s)
-
1 Day AgoYou just can't beat the styling from the 50s. Looks amazing!60 replies | 26171 view(s) -
1 Day AgoBegan the cut / buff process... Let's hope I can finish this faster than the painting process. LOL79 replies | 40130 view(s)
-
1 Day AgoI’m amazed by what you accomplish while having a full time job and a family. :)265 replies | 132610 view(s) -
1 Day AgoI haven't had much to update as I've only been driving the car and attending some car shows/cruise in's. Last weekend I decided to take my car on a...265 replies | 132610 view(s)
-
1 Day Ago1/2 Nicop will need a fairly large bend radius. Try to find a decent used dedicated 1/2 bender. Something like this...3 replies | 114 view(s)
-
1 Day AgoWay back inna dawn 'o time, I used to use my knee to bend tubing. Bend it over a bit, shift, bend a bit, shift back, over and over until either the...3 replies | 114 view(s) -
2 Days Agoanyone have any tips/advice on bending fuel lines? trying to run 1/2" feed with copper/nickel tube. i haven't had any luck with the tube wanting...3 replies | 114 view(s) -
2 Days AgoNot too many photos make me slow down, soak in, and really appreciate the time, love, and craftmanship as these do. I tip my hat to ya, well done. I...58 replies | 30882 view(s)
-
2 Days AgoThanks again for input everyone. Car only qualified as unfinished paint- very light body. Started instantly and rumbled smoothly every time until...7 replies | 163 view(s)
-
2 Days AgoTo the Top!!!9 replies | 2902 view(s) -
2 Days AgoOK, so other ECMs were already tried. Did any of the ECMs come online enough to set any codes? Seems strange that the original ECM would let you...7 replies | 163 view(s)
-
3 Days AgoI would give serious thought to getting a new standalone harness from a reputable source. This is the risk you take when you buy an unfinished...7 replies | 163 view(s)
-
3 Days AgoDon’t have original build or code info. Big part of problem is unknown wiring scheme7 replies | 163 view(s)
-
3 Days AgoStuff long gone? ������4 replies | 2226 view(s)
-
3 Days AgoWho modified the harness for the standalone swap? Is it throwing any codes?7 replies | 163 view(s)
