1967-1969 Camaro Chassisworks Suspenison

[jpierson77]

Full Chassisworks protouring suspension for 1967 1968 and 1969 Camaro

I bought this suspension in 2012 and installed in the car, the project stalled and the car has sat inside since 2012. I am finally getting the project going again. The car is going to be taking a different path now and so I have removed this suspension and I am looking to sell it. This has been powder coated and installed in the car but never driven.

What you are gettting:
Front Suspension
Chassisworks complete front subframe powder coated black
http://www.cachassisworks.com/p-696-...uspension.aspx
Chassisworks g-machine front clip suspenison
http://www.cachassisworks.com/p-3661...uspension.aspx
Chassisworks LS motor Mounts
http://www.cachassisworks.com/p-3801...rd-offset.aspx
Chassisworks front strut bars (does need firewall plates and tabs available from Chassisworks)
http://www.cachassisworks.com/p-2693...130-steel.aspx
Chassisworks G connector Support
http://www.cachassisworks.com/p-3116...t-bolt-in.aspx
Chassiworks bolt in subframe G connector
http://www.cachassisworks.com/p-3108...r-bolt-in.aspx
Chassisworks Drive shaft loop
http://www.cachassisworks.com/p-1593...r-support.aspx
Varishock bearing eye double adjustable Coil Overs
http://www.cachassisworks.com/p-930-...25-travel.aspx
Chassisworks T-56 Trans crossmember
http://www.cachassisworks.com/p-2214...6-6-speed.aspx



Rear Suspension
Chassiworks Canted 4 Bar G-link with pivot ball
http://www.cachassisworks.com/p-1299...uspension.aspx
You would need to buy part numbers 5355, 5366 and 3148-263.38-094, these are the frame rail brackets and bolts. These are welded in my car and are not salvageable.
Chassisworks Fab 9 rear end housing for splined sway bar, powder coated black
http://www.cachassisworks.com/p-803-...aled-ends.aspx
Strange Engineering 3rd noular 3rd member with Eaton Trutrack, 3.89 gears, 31 spline axles
Chassiworks splined sway bar
http://www.cachassisworks.com/p-1310...-roll-bar.aspx
Varishock bearing Double adjustable coil overs

All of this new would cost over $14k! Asking $10,000 buyer pays shipping, or depending on location we might be able to arrange a meet halfway delivery deal. Located in Fort Collins CO.

I also have a Baer Pro + 14" Front and SS4+ 13" Rear (Red) Brake kit and stainless headers that I had intended to re-use however if someone is looking for a package I would also sell those.

[1Bad Ls]

Pm sent

[jpierson77]

Sending it back to the top....

[ryeguy2006a]

I'd love to do this for my car, but I'm recovering from my engine swap this past winter. GLWS, great deal for someone.

[cwylie]

What offset wheels and size wheels does this setup call for?

[jpierson77]

I had 18x9 5.25 BS in the front bad 18x12.5 5.5 BS with mini tubs in the rear.

[automotivdesigngroup]

Still available? PM sent

[Erik Beckett]

If you decide to part anything out, I am a buyer on a few things. Text or call me PM'd my number

[NoSleeperII]

I would be in for the center section and possibly the brakes if you decide to part out

[jpierson77]

All pms replied to, sorry for the slow responses. I have been waiting on a set of replacement rear frame brackets so that the package is complete.

[automotivdesigngroup]

PM replied to.

[jpierson77]

Sale pending, thank you everyone for the interest. Will repost if anything falls through.