First Gen Camaro LS swap garage cleanout

[Johnzee67ls3]

Doing some shop cleanup and getting rid of extra parts. Parts will be shipped from 89431 with shipping paid for by buyer. Can pay paypal. For quicker response you can send me an email [email protected].





Moroso oil pan part#20142 and pickup#24050. Only used for mock up.-$350

Brand new Crower Cam 279, 285 .644 lift 113LSA. See picture of cam card for full details, to be used with solid rollers.-$400

Clayton Machine ignition coil covers part#LSC-01-M. Minor scratches, ready for paint. comes with mounting hardware.-$150

New Derale pwm 12’’ dual fans part#66842. 26’’ wide, 18’’ tall, 4’’ thick. Never installed, comes with all necessary electronics.-$400

Original 1967 Camaro gauge cluster, everything worked when pulled.-$100

New Holley spacers part#HLY21-1 and HLY21-2. The 21-1 is used for standard belt spacing on passengerside a/c bracket, the 21-2 is for Camaro (newer f body) passengerside spacing for a/c bracket.- $40 each

ATS/Speedtech engine mount plates part# SDP-ATS70001 Used for mock up, ended up going with Hooker mounts with my application. Energy suspension mounts, the lower metal ears are ground off. I will throw them in for free if full asking price is paid.-$100


Remanants of universal intake kit Airaid part #101-351. What you see is what you get- still some good pieces to fab up another intake system. You will need a couple rubber pieces that connect the hard plastic pipes. Air filter has small dent in mesh.-$150



LS MSD ignition coils part #MSD82648. Bolted on then taken off to go a different direction, don’t think it matters but they were used with a redone truck harness.-$300

Only used for mock up- Unisteer rack and pinion part #UIS8010540-01. Comes with what is pictured: Steering arms, pressure/return fittings, mounting spacers. Depending on application you will need longer lower control arm bolts for mounting. It has a couple of scratches from engine R&R and the heads of the fittings are ground down from clearance issues. It is my understanding this rack and pinion works best in the speedtech subframe w/LS or stock subframe with older SBC. With Hooker mounts and headers I did not have any luck incorporating this with the LS in factory subframe.-$600

[NoSleeperII]

How much for the crossmember shipped to 77389

[Johnzee67ls3]

Looks like $340 total for the crossmember shipped to 77389

[chem]

Interested in the subframe connectors, how much shipped to CA, 90601.

Thanks

Doing some shop cleanup and getting rid of extra parts. Parts will be shipped from 89431 with shipping paid for by buyer. Can pay paypal. For quicker response you can send me an email [email protected].



Moroso oil pan part#20142 and pickup#24050. Only used for mock up.-$350

Brand new Crower Cam 279, 285 .644 lift 113LSA. See picture of cam card for full details, to be used with solid rollers.-$400

Clayton Machine ignition coil covers part#LSC-01-M. Minor scratches, ready for paint. comes with mounting hardware.-$150

New Derale pwm 12’’ dual fans part#66842. 26’’ wide, 18’’ tall, 4’’ thick. Never installed, comes with all necessary electronics.-$400

Original 1967 Camaro gauge cluster, everything worked when pulled.-$100

New Holley spacers part#HLY21-1 and HLY21-2. The 21-1 is used for standard belt spacing on passengerside a/c bracket, the 21-2 is for Camaro (newer f body) passengerside spacing for a/c bracket.- $40 each

ATS/Speedtech engine mount plates part# SDP-ATS70001 Used for mock up, ended up going with Hooker mounts with my application. Energy suspension mounts, the lower metal ears are ground off. I will throw them in for free if full asking price is paid.-$100

Chevrolet Performance musclecar oil pan kit part#19212593. Comes with dipstick and tube, windage tray, and pickup. Pickup has bend past the o-ring, look at picture. When I installed it, the o-ring seated no problem.Used for mock up using stock subframe, hooker mounts, and rack and pinion. While it fit in a first gen Camaro, I did not like how low it hung down past the subframe. I’m sure someone else can put it to good use.$100


Remanants of universal intake kit Airaid part #101-351. What you see is what you get- still some good pieces to fab up another intake system. You will need a couple rubber pieces that connect the hard plastic pipes. Air filter has small dent in mesh.-$150


New DSE power steering pump part #091001. This style has the reservoir directly attached to the pump, I ended up needing one with the hose attaching the reservoir and pump.-$100


LS MSD ignition coils part #MSD82648. Bolted on then taken off to go a different direction, don’t think it matters but they were used with a redone truck harness.-$300

Only used for mock up- Unisteer rack and pinion part #UIS8010540-01. Comes with what is pictured: Steering arms, pressure/return fittings, mounting spacers. Depending on application you will need longer lower control arm bolts for mounting. It has a couple of scratches from engine R&R and the heads of the fittings are ground down from clearance issues. It is my understanding this rack and pinion works best in the speedtech subframe w/LS or stock subframe with older SBC. With Hooker mounts and headers I did not have any luck incorporating this with the LS in factory subframe.-$600


Brand new American Powertrain X-Factor crossmember for first gen Camaro part #XFGM-10101M. I had good luck using another one of these in a build using Hooker engine mounts, headers, and stock sub frame with LS3 and 4L80E. Fully adjustable to work with just about anything.-$300



New DSE first gen subframe connectors part#DSR-010101. Comes with everything pictured, the cut template will have to be downloaded from DSE’s site.-$130

[Johnzee67ls3]

Interested in the subframe connectors, how much shipped to CA, 90601.

$150 total shipped

[KAN KAN Speedshop]

I want the dse powersteering pump and the chevrolet performance muslecar oil pan and pickup. I'll send you a pm
KAN KAN SPEEDSHOP

[Johnzee67ls3]

PM's replied to.

[NoSleeperII]

I’ll take the crossmember. Please send me paypal info

[bill1969camaro]

Money sent for the DSE first gen subframe connectors

[Johnzee67ls3]

DSE power steering pump, GM oil pan, and subframe connectors, and crossmember sold.

[Johnzee67ls3]

Bump, coils sold. I also have a B&M Starshifter part#80675 with all the parts included except the screw on handle. $150

Hooker crossmember part#12626HKR, fits first gen Camaro with LS and T56, brand new $175.

Painless performance ls wiring kit part#PRF 60221 never used, to be used with throttle by wire with tac module 2003-2006 PCM's. $650

[belairboy55]

Do you still have the Clayton Machine covers still?