67'- 68' Camaro / Firebird Single DIN Radio Mounts

[jwcarguy]

First batch of single DIN radio mounts for 67-8 Camaro & Firebird available , now a solution to mount a modern radio head unit for the vast majority of people dealing with a cutup dash from over 50 years of owners! Have better quality, usually with many more options and less expensive than the two shaft type, pm me for details pics of installed unit in a customers 67’ before and after he had it & dash pieces hydro dipped when I did a 5th Gen Camaro console install w/ @watsons_streetworks billet p/w switches
You can paint to match interior, powder coat or hydro dip them
I will be sending messages to people that contacted me before after I made my first mount, more mounts are being built now
[FONT=Helvetica]$175 shipped/ insured/ paypal for bare mount w/ mounting hardware[B]
Price is $175 shipped (in US, all others, please contact me for shipping cost)
message me or





UPDATE 3-25-24 I did a batch of 12 mount kits, will be contacting people that have asked for them, plus made some extra mount kits see last page Thanks Jeff

[jwcarguy]

Thanks everyone for the great response on these radio mount kits, will keep building them, Thanks, Jeff

[Rod]

nicely done

[davidfre21]

I need something like this but to mount a double din

[jwcarguy]

I need something like this but to mount a double din

David,
I am actually working on a design/ sizing for a double DIN this week, since I have had a few people ask about it
Is your car a 67-68?

Thanks, Jeff

[minendrews68]

Good looking Jeff!

[7Knapp]

I want to order one. I'd like to see how the double din comes out to see if I want to invest in a new head unit.

[davidfre21]

David,
I am actually working on a design/ sizing for a double DIN this week, since I have had a few people ask about it
Is your car a 67-68?

Thanks, Jeff

It's a 68. I already bought the smooth delete panel to attempt myself but who knows when I'll get around to it. Plan on running vintage air controls.

[jwcarguy]

I want to order one. I'd like to see how the double din comes out to see if I want to invest in a new head unit.

I will keep you guys posted on double DIN mock up, big issue is covering the lower section of ash tray hole, where it rolls under dash and have it look good

Thanks, Jeff

[jwcarguy]

It's a 68. I already bought the smooth delete panel to attempt myself but who knows when I'll get around to it. Plan on running vintage air controls.

david, Here is a pic of a guy's 68 with the VA controls that installed my mount kit

[simon455]

I gotta anvil carbon center dash cover on the way, it's a blank one, I will need to cut opening for center vent and heater controls (dse adapter) in my case
Rest is still blank and covers the ashtray, there might be enough room to
Have a opening for a 2din. Will have to wait till I have it in my hands.

https://anvilauto.com/products/camar...ash-panel.html

[Camaro68+69]

Are you going to make any for a Double Din radio??

Scott

[davidfre21]

See, I don't care about the ashtray. It will be deleted with the new panel. But because of it, I'll have all the room from the VA controls down. Or I can mount the VA controls in the ashtray area and have all the room going up.

[jwcarguy]

Are you going to make any for a Double Din radio??

Scott

Working on design now
As you all know, issue is lower most opening ( bottom of ashtray hole) to make look correct and not a huge fabrication job with rolling lower section of bezel, etc?
Open for suggestions?
Thinking of having same outer bezel width at bottom, but maybe a separate piece ( as a block off) for lower ashtray opening, wich is hard to see when seated in car, especially with a console installed as well

[CarlC]

Is trimming needed if the radio section of the dash has not been molested?

[jwcarguy]

Is trimming needed if the radio section of the dash has not been molested?

Carl
Yes, the height of hole is 2 7/8” ( mesaured from upper horizontal dash structure, down , to line to trim) yhe upper dash structure remains intact
The width of hole is 8” ( centered)
Slight trimming on sides ( factory round holes for stock radio shafts) to clear side theeaded mounting bosses , that are part of the mount
I made up a “ install sheet” with diagram, dimensions and instructions

Thanks
Jeff

[oldschoolmuscle]

sweet I've been looking for something like this.

[jwcarguy]

sweet I've been looking for something like this.

Still have radio mount kits left
Pm me for ordering
Thanks
Jeff

[jwcarguy]

weekend bump

[jwcarguy]

weekend bump