Page 3 of 3 FirstFirst 1 2 3
Results 41 to 53 of 53
  1. #41
    Join Date
    Oct 2014
    Posts
    233
    Country Flag: United States
    Looks great! I'm jealous of all the room that LS allows vs. my stupid-big Coyote motor. Nice job.
    1988 Mazda RX7 - Forged LS/T56, 76mm turbo, ProEFI, Ford 8.8 - Sold
    1965 Mustang Coupe - TT Coyote, TR6060, big brakes, suspension. Basically a large car shaped hole in the ground I throw money into.
    2013 Focus ST - Daily Driver - FRPP Tune

  2. #42
    Join Date
    Aug 2004
    Location
    San Bernardino, CA
    Posts
    827
    I got all of the brake lines plumbed and all of the C5 brakes bolted in. I also dropped in the motor today. I added new GM exhaust manifold gaskets and new NGK colder plugs for the turbo. I would have installed the transmission but i goofed on the clutch and ordered a LS7 clutch and pressure plate and failed to get the proper flywheel. I have an aluminum fidonza LS1 flywheel and a stock LS1 flywheel kicking around. I can either buy the correct LS7 flywheel or buy the correct LS1 clutch and pressure plate. The cheaper option is to get an LS7 flywheel.

    Enjoy the pics. More to come.












    How do you all think my waste gate dump will work?

  3. #43
    Join Date
    Oct 2014
    Posts
    233
    Country Flag: United States
    The wastegate priority is very good, should work excellent.
    1988 Mazda RX7 - Forged LS/T56, 76mm turbo, ProEFI, Ford 8.8 - Sold
    1965 Mustang Coupe - TT Coyote, TR6060, big brakes, suspension. Basically a large car shaped hole in the ground I throw money into.
    2013 Focus ST - Daily Driver - FRPP Tune

  4. #44
    Join Date
    Aug 2004
    Location
    San Bernardino, CA
    Posts
    827
    Well guys, its been a year... had lots of ups and downs, switched jobs twice, but i never stopped tinkering on the car. Its actually up and running. The holley efi was super simple to slap on the car. I am using the base turbo LS tune. About the hardest thing i had to do was adjust the throttle body blade to achieve a better hot IAC position. As it sat it would idle but die when you revved it. I had to remove the throttle body 5-6 times to get it just right, now I can rev the engine til the blow off valve opens and it will just idle down as normal.

    After I got it running, about March of this year I walked away from it while i adjusted to new jobs and income. I have since started to strip the entire car and piece by piece put it all in SPI black epoxy. Man the car is pretty dented under all that nasty ass buff primer and old body work. who ever did the body work did a great job but the car sat outside for so long i had no choice but to take it down to bare metal.

    Here comes the pictures. Feel free to ask questions.

  5. #45
    Join Date
    Aug 2004
    Location
    San Bernardino, CA
    Posts
    827
    Ls1 v Ls7 flywheel



    Look at this rats nest, holley wiring is good but i have no idea who designed the harness layout. lots of ends are too short or too long.





    got the dash installed to monitor the engine





  6. #46
    Join Date
    Aug 2004
    Location
    San Bernardino, CA
    Posts
    827
    look at this thick ass primer! and for all you wondering, I bought an eastwood contour sct and it kicks ass on FLAT surfaces only! the rest was wire wheel and a rust stripping disk.





















    Repo rear valance fit OK




  7. #47
    Join Date
    Apr 2001
    Location
    The Druid City
    Posts
    14,392
    Country Flag: United States
    Glad to see you making progress!
    1970 GTO Version 2.0
    1967 Cougar build
    GM High-Tech Performance feature
    My YouTube Channel Please Subscribe!
    Instagram @projectgattago

    "You were the gun, your voice was the trigger, your bravery was the barrel, your eyes were the bullets." ~ Her

  8. #48
    Join Date
    Apr 2006
    Location
    Huntington Beach, CA
    Posts
    2,320
    Country Flag: United States
    Man, I remember your first build thread. Glad to hear you finally got this thing drivable (before tearing it down again). Did you get any video of it running?

  9. #49
    Join Date
    Aug 2007
    Location
    Denton Texas
    Posts
    1,147
    Country Flag: United States

  10. #50
    Join Date
    Aug 2004
    Location
    San Bernardino, CA
    Posts
    827
    Quote Originally Posted by Chad-1stGen View Post
    Man, I remember your first build thread. Glad to hear you finally got this thing drivable (before tearing it down again). Did you get any video of it running?
    <iframe width="560" height="315" src="https://www.youtube.com/embed/7tpK50X1LMo" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>

    why isnt the youtube video not working?

    https://youtu.be/7tpK50X1LMo

  11. #51
    Join Date
    Apr 2006
    Location
    Huntington Beach, CA
    Posts
    2,320
    Country Flag: United States
    Quote Originally Posted by DCx View Post
    <iframe width="560" height="315" src="https://www.youtube.com/embed/7tpK50X1LMo" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>

    why isnt the youtube video not working?

    https://youtu.be/7tpK50X1LMo
    Don't use the embed code. Use either the share URL or default URL with the [ video ] tags.


  12. #52
    Join Date
    Aug 2004
    Location
    San Bernardino, CA
    Posts
    827
    Not much else to add. Still putting the car in epoxy one panel at a time. I did the door shells and cowl this last weekend.






  13. #53
    Join Date
    Oct 2014
    Posts
    233
    Country Flag: United States
    Progress is looking good. Those are some real PITA steps, haha. Good work keeping on it!
    1988 Mazda RX7 - Forged LS/T56, 76mm turbo, ProEFI, Ford 8.8 - Sold
    1965 Mustang Coupe - TT Coyote, TR6060, big brakes, suspension. Basically a large car shaped hole in the ground I throw money into.
    2013 Focus ST - Daily Driver - FRPP Tune

Page 3 of 3 FirstFirst 1 2 3