2nd Generation Camaro Speaker Kick Panels FS (AR)

[1976CamaroGuy]

Speaker Kickpanels

Made of fiberglass, holds a oversize 6.5" component set and clears the parking brake with a little modification :smoke:

Uses the area behind the stock kick panel for the speaker magnet, so you will lose the pull knob function on non-ac and the passenger vent flapper or ac models.

Fits any and all 1970-1981 Camaro or Firebird

$165 shipped a set to lower 48 states

https://static1.pt-content.com/images/pt/2011/02/DSCF4122-1.jpg

https://static1.pt-content.com/images/pt/2011/04/aaa36256_zpsbgbkjnll-1.jpg

https://static1.pt-content.com/images/pt/2011/04/file118_zpsdotto7hl-1.jpg

https://static1.pt-content.com/images/pt/2011/04/camaro00525_zps28cd6c9c-1.jpg




Added kick panels for 67-69 Camaro / Firebird $165 shipped to lower 48 states


Will have the mdf grill blanks, panels, and pinch weld moldings. The kicks will butt against that.

These will need some final prep before covering or painting them like you would any body panel, but hey I'm basically pulling them out of the mold, trimming and sending them out. Otherwise I would be asking double that like the other guys selling similar pods.

These use the cavity behind the kick where the vent actuator resided so you will lose that. To protect the speaker from water draining off the cowl get a set of metra 91-6900 6 x 9 speaker baffles from eBay, they fit inside the opening perfectly and you can get those for $9-12 shipped.


https://static1.pt-content.com/images/noimg.gif (http://s1310.photobucket.com/user/1971camaroguy/media/67-69%20kickpanels/2015-03-29%2016.51.57_zpsmjoclqrl.jpg.html)

https://static1.pt-content.com/images/noimg.gif (http://s1310.photobucket.com/user/1971camaroguy/media/67-69%20kickpanels/2015-03-29%2016.53.09_zpsejfmtyix.jpg.html)

https://static1.pt-content.com/images/noimg.gif (http://s1310.photobucket.com/user/1971camaroguy/media/67-69%20kickpanels/2015-03-29%2016.52.29_zpsxkuj0cuv.jpg.html)

https://static1.pt-content.com/images/noimg.gif (http://s1310.photobucket.com/user/1971camaroguy/media/67-69%20kickpanels/2015-03-29%2016.52.25_zpsnaixxjdt.jpg.html)

https://static1.pt-content.com/images/noimg.gif (http://s1310.photobucket.com/user/1971camaroguy/media/67-69%20kickpanels/2015-03-29%2016.52.23_zpstydlpwd0.jpg.html)

https://static1.pt-content.com/images/noimg.gif (http://s1310.photobucket.com/user/1971camaroguy/media/67-69%20kickpanels/2015-03-29%2016.52.18_zps6m3rjivg.jpg.html)

https://static1.pt-content.com/images/noimg.gif (http://s1310.photobucket.com/user/1971camaroguy/media/67-69%20kickpanels/2015-03-29%2016.52.14_zpsu0ndcmll.jpg.html)

https://static1.pt-content.com/images/noimg.gif (http://s1310.photobucket.com/user/1971camaroguy/media/67-69%20kickpanels/2015-03-29%2016.52.06_zpsg9gpqley.jpg.html)

https://static1.pt-content.com/images/noimg.gif (http://s1310.photobucket.com/user/1971camaroguy/media/67-69%20kickpanels/2015-03-29%2016.52.03_zpsy99pxrx9.jpg.html)

https://static1.pt-content.com/images/noimg.gif (http://s1310.photobucket.com/user/1971camaroguy/media/67-69%20kickpanels/2015-03-29%2016.52.01_zpsfhqsohjh.jpg.html)

https://static1.pt-content.com/images/noimg.gif (http://s1310.photobucket.com/user/1971camaroguy/media/67-69%20kickpanels/2015-03-29%2016.51.57_zpsmjoclqrl.jpg.html)

https://static1.pt-content.com/images/pt/2011/04/Untitled_zpswjltowm1-1.jpg

https://static1.pt-content.com/images/pt/2011/04/_121_zpsrjtitb6u-1.jpg

https://static1.pt-content.com/images/pt/2011/04/_12_zpszamtk7s9-1.jpg

I have two sets of 70-81 Camaro or Firebird Speaker package trays $185 shipped to lower 48 states. Has center section for a subwoofer

(I don't make these year round, seasonal only). Comes in fiberglass with white gel coat as pictured. U finish it out.

https://static1.pt-content.com/images/pt/2011/04/DSCF4355_zpsvilubhod-1.jpg

https://static1.pt-content.com/images/pt/2011/04/2015080620160901_zpshznn7iav-1.jpg

https://static1.pt-content.com/images/pt/2011/04/2015080620161147_zpso6q8dlr2-1.jpg

https://static1.pt-content.com/images/pt/2011/04/2015070520202554_zps2rcjyzaq-1.jpg

[1976CamaroGuy]

bump

[1976CamaroGuy]

bump

[syborg tt]

Hi

Do you have any pictures of them installed ?

[John Wright]

Sy are you using the factory a/c?

[syborg tt]

Sy are you using the factory a/c?

Nope - but i can make you a smoking deal on a complete factory set up

[John Wright]

I have factory A/C...and it works...but I'm looking very hard at the Vintage Air. I was going to say that if you were using your factory air, that the speaker for the pass kick panel may not work due to the A/C using that flap on that side.

[syborg tt]

I am looking into the vintage air also but I am seriously thinking that I may run the car without air.


I have factory A/C...and it works...but I'm looking very hard at the Vintage Air. I was going to say that if you were using your factory air, that the speaker for the pass kick panel may not work due to the A/C using that flap on that side.

[1976CamaroGuy]

Back to top, $165 shipped to lower 48

https://static1.pt-content.com/images/pt/2011/06/DSCF4248-1.jpg

https://static1.pt-content.com/images/pt/2011/06/DSCF4249-1.jpg

https://static1.pt-content.com/images/pt/2011/06/DSCF4250-1.jpg

https://static1.pt-content.com/images/pt/2011/06/DSCF4251-1.jpg

[1976CamaroGuy]

TTT I have a set or two to sell if anyone is thinking of a good Christmas present to give someone.

[1976CamaroGuy]

Hi

Do you have any pictures of them installed ?

Here's someone that bought a set, I believe it was a 1973 Camaro z28

https://static1.pt-content.com/images/pt/2011/11/IMG_0189-1.jpg

https://static1.pt-content.com/images/pt/2011/11/IMG_0149-1.jpg

https://static1.pt-content.com/images/pt/2011/11/IMG_0147-1.jpg

[g-machine]

Please shoot me an email about these! :twothumbs

[email protected]


Thanks,
George

[1976CamaroGuy]

Hey George,

Sent you a email - Thanks again

[1976CamaroGuy]

Please shoot me an email about these! :twothumbs

[email protected]


Thanks,
George

Hey George,

I replied to your email with a shipping quote and details. Never heard back.

[ldj1970]

Hi, I'm interested in a set of these, [email protected] Thanks

[1976CamaroGuy]

Hi, I'm interested in a set of these, [email protected] Thanks

I sent you a PM, let me know. I sold two sets yesterday and one last week. I have about five left so they are going pretty quick.

Thanks

[g-machine]

Just sent you an email - count me in!

Thanks,
G

[1976CamaroGuy]

Just sent you an email - count me in!

Thanks,
G

Email replied, thanks again

[1976CamaroGuy]

Four sets left :-)

[g-machine]

Please email me with payment info.

Thanks!

G

[1976CamaroGuy]

ok no prob, payment info sent

Thanks,

Dennis


Please email me with payment info.

Thanks!

G

[1976CamaroGuy]

Three sets left :-)

I have them listed on eBay as well, can't hold them for anyone. First come first serve. I will adjust my quanity on eBay if I sell them on a local forum first.

[1976CamaroGuy]

Two sets left :-)

[1976CamaroGuy]

Please email me with payment info.

Thanks!

G

Hey George, down to one sets, I have it on eBay too so it can sell anytime. Did you get my payment info yet?

Let me know,

Dennis

[1976CamaroGuy]

one set left !

[1976CamaroGuy]

Just sold my last set 30 minutes ago, I'm all out now

Thanks everyone for looking

[veeeper]

Are you going to make any more? If so, email me at [email protected]

[1976CamaroGuy]

I will around march or so, wanted to wait until spring time when the weather started getting nice again. The fiberglass cures better when the temps outside are above 60 degrees. Plus I have some much needed work to get done on my personal car too.

Just keep an eye on the posts in the next few months and I'll update it when I replenish stock.

Thanks

Dennis

[maxxom]

I will around march or so, wanted to wait until spring time when the weather started getting nice again. The fiberglass cures better when the temps outside are above 60 degrees. Plus I have some much needed work to get done on my personal car too.

Just keep an eye on the posts in the next few months and I'll update it when I replenish stock.

Thanks

Dennis

Please email [email protected] when available.

[1976CamaroGuy]

Please email [email protected] when available.

I will, just keep and eye on this thread. I'll update when I start selling again. I shoot you an email as well.

Thanks,

Dennis

[critter]

So are you in Jonesboro? I'm in Little Rock. I might be interested when you start up again.

[1976CamaroGuy]

So are you in Jonesboro? I'm in Little Rock. I might be interested when you start up again.

About 15 minutes from jonesboro, I work there though. :)

[shanezz]

I'm ready when you are,e-mail [email protected]

[1976CamaroGuy]

ok sounds good, I'm going to have to re-tool my molds, but still shooting for around middle of march (less than a month). I ordered some more pinch weld a week or so ago.

When I do start I'm going to try and make a batch of four- five sets at a time

Thanks again

[70Uglybird]

Hey do you think it would be possible to make a set that has the top narrow channel as well? What have people been doing with the exposed metal after installing these?

[1976CamaroGuy]

Hey do you think it would be possible to make a set that has the top narrow channel as well? What have people been doing with the exposed metal after installing these?

It's possible, but would be a little more difficult to do with a channel. Instead I supply two pieces of pinch weld moulding to cover the exposed metal..it has a black textured finish similar to weatherstripping

It's shown in the pics attached on the first page

https://static1.pt-content.com/images/pt/2011/06/DSCF4248-1.jpg

[1976CamaroGuy]

I've got one set to sell, it got somewhat warm yesterday and I was able to make a set. I just need to let them finish curing, trim them up and they'll be ready to ship by the weekend.

I have them listed on eBay but if any wants them shoot me a PM with your zip and I'll give you a shipping quote and payment info.

I'm not going to be able to make anymore at the moment, going to have to re-tool for sure on the next batch

[1976CamaroGuy]

set sold yesterday everyone

[1976CamaroGuy]

Spring is here, I'm making kickpanels again :-)

[jtmiller92]

How much for a set shipped to 40356? They will be for my 72 Camaro.

[1976CamaroGuy]

How much for a set shipped to 40356? They will be for my 72 Camaro.

Shipping will be $15.97, just shoot me a PM if your interested and we can work out the details.

Thanks again

[1976CamaroGuy]

To the top

[g-machine]

Got new molds ready to go?

[1976CamaroGuy]

Yep, sold about three-four sets already on the new molds :)

[1976CamaroGuy]

Ttt

[1976CamaroGuy]

Here's some threads from the camaro forum of the installations of some of the guys that have gotten a set. Firebird would be the same.

http://www.nastyz28.com/forum/showthread.php?t=225025&page=3

http://www.nastyz28.com/forum/showthread.php?t=228177&page=12

[gold79ta]

Would you happen to have a set made up ready to ship?

[1976CamaroGuy]

Would you happen to have a set made up ready to ship?

I do have a set ready, message sent

[gold79ta]

money sent.

[1976CamaroGuy]

money sent.

Got it :) I'll get these out to you in the morning and get a tracking number to you. - Thanks again

[1976CamaroGuy]

I have all of the sets I am going to make done now, I have them listed on the Camaro forum I frequent as well. Not planning on making any more sets as it is getting colder now. These are the last run for a while....I "might" make some more in the spring but planning on buying a new house then and may take up my time. I also do these in my spare time and I really need to get started back on my 71.

Basically what I am saying is what I have on hand will be it for a while, if not indefinitely. So get a set while I have them.

I'll try my best to keep this thread updated as best as I can, just keep in mind as they dwindle down. But I wouldn't wait if your build is centered around something like this. Ready to ship and I will send a tracking number after payment is made. Shipping will run $12-17 inside lower 48 states depending on location. Canada will be a flat $42.75 shipping via USPS.

Right now the current number is :

10 Sets Left

[1976CamaroGuy]

8 Sets Left

[1976CamaroGuy]

7 sets left

[1976CamaroGuy]

4 sets left

[carbuff]

I am perhaps interested in a set of these. I read through the threads which you linked above, but I didn't notice any comments about the quality of the sound coming from a tweeter mounted that low. It's a little difficult to tell how much the tweeter is 'aimed' at the driver from that position. Can you share any observations?

Regardless, I am pretty interested in a set. How do you receive payment?

[1976CamaroGuy]

Hi,

The sound quality is fine with the tweeter that low. It does have a slight angle to it. The drivers tweeter has a slight harder angle than the passenger side.

But most tweeters can swivel too for more imaging. This is how car audio systems have been designed for years. Moving the speakers to the kicks to equalize the path lengths to the ears.

PM sent

Dennis

[1976CamaroGuy]

Ttt

[hatcher1986]

Glad I ordered mine this morning. Thanks Dennis I'm looking forward to getting them.

[1976CamaroGuy]

No problem :-)

[1976CamaroGuy]

Just a heads up, anyone that has bought the kick panels, found a source for the baffles at a good price. $6.99 shipped on ebay

http://www.ebay.com/itm/220921975446?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649

[1976CamaroGuy]

Got a couple sets left if anyone is interested

[linzbach]

Thanks for the kick panels, Dennis. They are great and really exceeded my expectations. Great instructions and nice quality. Looking forward to getting them installed. Thanks Again.

[1976CamaroGuy]

Thanks for the kick panels, Dennis. They are great and really exceeded my expectations. Great instructions and nice quality. Looking forward to getting them installed. Thanks Again.

No problem and thank you, glad you like them

[1976CamaroGuy]

Bump'n it up

[1976CamaroGuy]

TTT

$12 flat rate shipping to anywhere in lower 48 states

[1976CamaroGuy]

Sold out now guys, sold last set to G-machines

[g-machine]

email & pm sent!

[5spd540]

I need to install mine they have been in the box for over a year

[Gasman303]

Have you made any more? I'm interested for my 71 camaro, thanks
[email protected]

[1976CamaroGuy]

Have you made any more? I'm interested for my 71 camaro, thanks
[email protected]

Not yet, planning on making some more mid-march when weather gets better. I can put you on my list when I start getting some sets ready and shoot you an email?

Just let me know,

Dennis

[Gasman303]

Awesome... Please let me know!! Thanks Nic

[1976CamaroGuy]

Awesome... Please let me know!! Thanks Nic

No problem, will do

[1976CamaroGuy]

Awesome... Please let me know!! Thanks Nic Hey Nic, sent ya a PM

[NTAjoe]

I'd like a set too. Thanks!

[k9kevin81]

Im in for a set!

[1976CamaroGuy]

I'm in the processes of selling my home, and buying a new one. So I have a lot on my plate right now. Hopefully I can start back making them again in about a month or so when I get settled in. Once I get my house ready to sell and I'm done with that part, I may go ahead and make some sets a little sooner, but I will put you on my list and let you guys know. Thanks again :-)

[sdta73]

Please let me know when you make some more after your move.....

[1976CamaroGuy]

Please let me know when you make some more after your move.....

I def will, thanks again

Dennis

[carbuff]

Pictures of my set wrapped in vinyl and ready to go into the car. We used some 1/8" Dynaliner that I had leftover from the rest of the interior to 'pad' the surface of the glass, then stretched the vinyl over that. They turned out great!

https://static1.pt-content.com/images/pt/2013/04/IMG_20130409_223850_small_zps53948cb2-1.jpg

https://static1.pt-content.com/images/pt/2013/04/IMG_20130409_223931_small_zps51d8dd35-1.jpg

[carbuff]

Here are a couple of pictures of the install. We attached the speaker to an aluminum plate which was screwed to the metal structure behind the kick panel. The kick panel itself just holds the grill.

https://static1.pt-content.com/images/pt/2013/04/update_0410_18_zpsb0f67196-1.jpg

https://static1.pt-content.com/images/pt/2013/04/update_0410_20_zpsd2a38929-1.jpg

[1976CamaroGuy]

^ that looks awesome, great work on the covering

[1976CamaroGuy]

just a FYI, I got my supplies out of storage and going to make a few sets before I move. I still have a month before the closing date. It's going to be first come first serve and I'll message the people on my list as they become ready. I'm hoping to get everyone taken care of before the move so I can start back on my car again and make some more in the fall.

[gearheadperformance]

I will take a set if your have any available.

[1976CamaroGuy]

I will take a set if your have any available.

I do have some available at the moment

[polyrocks]

Also intrested, pM sent


I do have some available at the moment

[gearheadperformance]

I got mine the another and they look great!

[dhutton]

I also got a set. They do look good.

[1976CamaroGuy]

Glad you guys like them :)

Thanks again

[1976CamaroGuy]

Still have some avail

[gold79ta]

Question for anyone that has installed these,
Have any of you used any of the filler stuff that they put inside sub boxes to ?
The white batting like material.
I am almost done installing mine and as of now I dont really like the sound im getting ,
I installed some jl audio seperates hooked up to a jl 5 channel amp with plenty of power and can barely tell they are there

[1976CamaroGuy]

Question for anyone that has installed these,
Have any of you used any of the filler stuff that they put inside sub boxes to ?
The white batting like material.
I am almost done installing mine and as of now I dont really like the sound im getting ,
I installed some jl audio seperates hooked up to a jl 5 channel amp with plenty of power and can barely tell they are there

A lot of things can influence how loud the speakers will get and or / sound. Which jl amp specifically are you using? Are you sending more than 100 watts rms to the speakers?

How about the exhaust system? Is it stock or do you have something with a little rumbled? These cars are inherently noisy, do you have any sound deadening / damping installed? If you have an aftermarket exhaust or cam in the engine your going to need more power for the speakers to compensate for that.

On my personal car I am going to use some pillow stuffing in the enclosure, more for damping the speaker. I did however drill a large hole in the bottom of the enclosure for the speaker to breath, mostly because the speakers we use are designed for infinite baffle like when mounted in the door. I didn't want to seal it completely up.

Hope that helps :)

https://static1.pt-content.com/images/pt/2013/05/DSCF5216-1.jpg

[carbuff]

We sealed mine up with the same 'box' in the back that was shown above. We didn't add the hole though. I did add Dynamat around the box to seal it to the edges. I've only just powered my setup up this week, but I have plenty of mid/low bass. We were able to tweak the crossovers to balance out the tweeter. I haven't driven the car yet to hear how it will sound with outside noise though...

[gold79ta]

Hey it s me again.
I just thought of using the billow stuffing right before I logged on.
Anyway im using jl audio 700.5 amp
http://www.crutchfield.com/S-oz9FOXfN9UV/p_136XD7005/JL-Audio-XD700-5.html

75 watts to front and rear 300 to a sub, I have no sub yet.
I am now having a hard time installing Ebrake.
Can I just take off?
I know it says you can bend it slightly but How being installed in car still/Car was not running when I tried them

[gold79ta]

I am using jl audio speakers but not the quality onesTHet dont have a seperate crossover unit just something like a bass blocker.
these ones

http://www.ebay.com/itm/JL-Audio-TR650-CSi-2-Way-6-5-Car-Speakers-System-/271068648296?pt=Car_Speakers&hash=item3f1cf35368#ht_511wt_1328

[1976CamaroGuy]

Hey it s me again.
I just thought of using the billow stuffing right before I logged on.
Anyway im using jl audio 700.5 amp
http://www.crutchfield.com/S-oz9FOXfN9UV/p_136XD7005/JL-Audio-XD700-5.html

75 watts to front and rear 300 to a sub, I have no sub yet.
I am now having a hard time installing Ebrake.
Can I just take off?
I know it says you can bend it slightly but How being installed in car still/Car was not running when I tried them

Do you have speakers in the rear? Are you fading them out relative to the front or do you have them amped like the front speakers? The reason I ask is that you'll need the rear speakers turned down quite a bit to provide only "fill" to the rear. If not they'll be overbearing and conflict with the front speakers. This can throw the sound off.

I'm going to use rear speakers in my Camaro but they are just going to be running off the radio....no amp. My front speakers in the kicks and the subwoofer will be the only thing amped up.

Don't remove your parking brake, if it's hitting the grill and you don't want to bend it slightly.....shim it to the right a little with washers at the mounting points. This will get you a little more clearance if the grill is hitting. But most cases it won't unless you have extra thick grills. The parking brake is a PIA to deal with, but I wouldn't take it out.

[1976CamaroGuy]

I am using jl audio speakers but not the quality onesTHet dont have a seperate crossover unit just something like a bass blocker.
these ones

http://www.ebay.com/itm/JL-Audio-TR650-CSi-2-Way-6-5-Car-Speakers-System-/271068648296?pt=Car_Speakers&hash=item3f1cf35368#ht_511wt_1328

On those you should have just gotten a crossover for the tweeter. What's the crossover point set on the amp for these? If they can handle it I would go something like 100 hz or so on the high pass and 100 hz on the subwoofer so there are no gaps in the crossover points.

[gold79ta]

Front and rears are amped, grills are not that deep.

[1976CamaroGuy]

Ok, here's what I personally would do with that set-up, if it were me

1. Bridge the amp into 3 channel mode

2. Run two channels to the front speakers (200 watts rms x 2)

3. Run 300 watts rms x 1 to either a single 2 ohm subwoofer or multiple 4 ohm subwoofers (just make sure your getting 2 ohms at the amp)

4. Run the rear speakers off the radio

The only thing I can see is that you might need to upgrade the front speakers, because even as is, they are only rated at 50 watts rms.

[gold79ta]

Hey 76 camaro guy, Im actually having a hard time installing thes on the driver side, Not that much of do it yourself guy.
But its not the pedal that hits the speaker its the actual bracket that holds the pedal that bolts to the side and thru the fire wall

[1976CamaroGuy]

Hey 76 camaro guy, Im actually having a hard time installing thes on the driver side, Not that much of do it yourself guy.
But its not the pedal that hits the speaker its the actual bracket that holds the pedal that bolts to the side and thru the fire wall

Ok no problem, make sure that you've fitted and trimmed enough off the kick so that it's sitting as flat as possible. Then if the bracket is hitting for whatever reason add some washers behind the actual parking brake bracket where it bolts to the side of the kick panel and shim it to the right to get it off the kick if it's hitting. If that doesn't work, pm me some pictures so I can see whats going on

[gold79ta]

I cant even get it close enough to the stud to get the nut on it.

[1976CamaroGuy]

Yeah I'm gonna need to see pics to be able to help you. Lets keep this going via pm as this just a for sale thread. Or we can make one in another forum section to figure this out. It should bolt up fine, not sure what is going on.

[gold79ta]

Hey guys no need to worry about fitting, I found what was the problem , my fault, nothing to do with this product.
When I put in the speaker baffle I did not notice it did not fit flush so it was not allowing the panel to lay flat.
Trimmed it up and now it fits great.

[1976CamaroGuy]

cool, I'm glad you got it sorted out :)

Thanks again

[1976CamaroGuy]

still have a few sets available

[1976CamaroGuy]

Ttt

[lotus]

Hi, do you still have some of these? If so, I am interested in a set. I do have a question though. I have a 74 firebird (manual shift with factory AC) will these work?

Thanks,
Pait

[1976CamaroGuy]

I sold my last set Friday, I planned starting up in the fall with another round. But I have supplies on the way so it may be sooner, the next few weeks. I'll let ya know either way. But to answer your question, they'll fit your car. You'll just lose the fresh air vent on the passenger side kick and the line will need to be capped off.

Dennis

[lotus]

darn and thanks for the quick reply. Let me know when you make more. I am not in a hurry as I am not really on interior yet anyways. :)

[1976CamaroGuy]

No problem, when I have some more available I'll update this thread :)

[1976CamaroGuy]

FYI, I'll have a couple of sets for sale after this weekend if anyone is interested

[g-machine]

pm sent

[jimrens]

Sent you a pm. Let me know and I'll take one set.

[1976CamaroGuy]

Ttt

[1976CamaroGuy]

Ttt

[1976CamaroGuy]

Ttt

[Tomcuschieri]

Ok you sold me on them! I'll take a set. Message me on how much and how to pay for them! They look great! Thanks, Tom

[1976CamaroGuy]

Ok you sold me on them! I'll take a set. Message me on how much and how to pay for them! They look great! Thanks, Tom

sounds good - PM sent

[1976CamaroGuy]

last set sold to Tom - thanks again, sold out for now

[g-machine]

Sweet price......wish I had waited a month longer!




TTT

I have a couple sets to sell right now, will discount them as a "special" to move them for $130 + shipping a set

Planning on doing a run during Christmas season at reg price, when those sell I'll make some more next fall.

[1976CamaroGuy]

TTT- Starting the run a little early, back to reg price again, but free shipping to lower 48 states - $165 shipped

It's getting colder and wanted to make sure I got enough done for the Christmas and tax season

[syborg tt]

If your thinking about adding speakers to your car. This is the product to buy and it's on the only one that has fit without any hassle.

Nice Work and I will get you pics of these installed in 2nd Chance after Sema.

[1976CamaroGuy]

That would be awesome :-) ....Thanks for the props

Dennis

[syborg tt]

That would be awesome :-) ....Thanks for the props

Dennis

Your Welcome and thank you for taking the time to make these.

[1976CamaroGuy]

bumpity bump

[1976CamaroGuy]

Ttt

[1976CamaroGuy]

couple of sets left.....

[1976CamaroGuy]

3 sets left - Just a heads up

it's payday and getting closer to Christmas

[1976CamaroGuy]

one set left!

[1976CamaroGuy]

all gone

[1976CamaroGuy]

ramping back up for a little bit, I have a few sets available right now

[1976CamaroGuy]

Added speaker door panels to my 1st post in case anyone didn't want or couldn't do kicks

https://static1.pt-content.com/images/pt/2014/04/20140419065928_zps472beac5-1.jpg

[minendrews68]

So your in Jonesboro? So am I.... I didn't think anyone from around here was on Pro-touring. Where are you?

[1nastyZ06]

Pm sent

[1976CamaroGuy]

So your in Jonesboro? So am I.... I didn't think anyone from around here was on Pro-touring. Where are you?

Hey Carl,

Live in Trumann, work in Jonesboro...I work for Nettleton Schools in town

[minendrews68]

We'll have to get together sometime and exchange lies... lol My daughter graduated from Nettleton


Hey Carl,

Live in Trumann, work in Jonesboro...I work for Nettleton Schools in town

[1976CamaroGuy]

sounds good :-)

[1976CamaroGuy]

That time of year again, I'm trying to get my Camaro to the body shop. I've been making a few sets here and there but as soon as I have my shop cleared out I'm going to make a small run of these to sell from now through Christmas while the weather is still nice.

[1976CamaroGuy]

If you have a third gen Camaro or firebird I have a couple of door speaker enclosures FS for those cars...$215 shipped to lower 48




https://static1.pt-content.com/images/noimg.gif (http://s1310.photobucket.com/user/1971camaroguy/media/For%20Sale/584f381b-2d87-4be0-b4f2-63e09d777a4f_zps2c9281d6.jpg.html)



https://static1.pt-content.com/images/noimg.gif (http://s1310.photobucket.com/user/1971camaroguy/media/For%20Sale/2014-10-19141756_zpsec3965dd.jpg.html)

https://static1.pt-content.com/images/pt/2014/10/DSCF3029_zps3c524724-1.jpg (http://s1310.photobucket.com/user/1971camaroguy/media/DSCF3029_zps3c524724.jpg.html)

[joeljet]

did you ever think of redoing the 2nd gen 2 piece lower door panel (I think for the 71-73)? you could get rid of the forward pocket.

[1976CamaroGuy]

I thought about it, but it's more work than I can devote time wise right now. But thanks for asking

[Nothingface5384]

Never k we anyone made kick panels or door pads for a 2nd Gen
ill let my uncle know about the kicks

[1976CamaroGuy]

Thanks, just have him let me know

[1976CamaroGuy]

Ttt

[rob1970z]

i would like to purchase a pair of your kick panels, how should i pay you?

[1976CamaroGuy]

sending PM

[Nothingface5384]

on the 2nd gen kick panels
What size for tweeter? does it fit?
Any depth restrictions for woofer?

[1976CamaroGuy]

Whats the price on the 2nd gen kick panels
What size speakers or tweeter? does it fit?
Any depth restrictions?

$165 shipped to lower 48 states

Fits 6.5" speakers with a max grill diameter of 7"....and any size flush mount tweeter

No real depth restrictions, speaker resides in cavity behind the kickpanel.

I suggest using a metra 81-6900 speaker baffle behind the speaker because it fits the opening perfectly and will protect your speaker from the elements. Max depth on that is about 4" deep.

Just let me know, these are ready to ship out - tracking provided

[1976CamaroGuy]

i would like to purchase a pair of your kick panels, how should i pay you?

Hey Rob,

I sent a PM but never heard back - Just let me know and thanks

[bad element 69]

i would like to purchase a pair of your kick panels, how should i pay you?

Hey Rob,

I sent a PM but never heard back - Just let me know and thanks


Dennis, i purchased them for rob as he doesn't have a paypal. He is a little old school. Thanks again Jamie

[1976CamaroGuy]

Ah gotcha - thanks

[1976CamaroGuy]

I have a package tray for 70-81 Fobody FS, uncovered fiberglass w/gel coat - Will let go for $215 shipped to lower 48 states

Holds a 6.5" speaker on either side
Water proof compared to factory cardboard stuff
Has a center recess for a subwoofer to fire through...1/2" mdf grille included

https://static1.pt-content.com/images/pt/2014/11/DSCF4274-1.jpg

What it looks like covered

https://static1.pt-content.com/images/pt/2011/07/reardeck-1.jpg

[1976CamaroGuy]

Ttt

[1976CamaroGuy]

Bumpity Bump...have several of each right now. Ready to ship

[1976CamaroGuy]

Sold out for now - I might make some more kicks the future. Not pushing the package trays, if you want to one I can make it to order

[Nothingface5384]

Kick panels do come with speaker holes allready cutout correct?
Are you able to modify the rear panel for either 1 6.5 or 1 8in in center to free air a subwoofer?
79 camaro
Thanks in advance

[1976CamaroGuy]

Kick panels do come with speaker holes allready cutout correct?
Are you able to modify the rear panel for either 1 6.5 or 1 8in in center to free air a subwoofer?
79 camaro
Thanks in advance

They don't already have the speaker holes cut out, but I can do that for you if you tell me what size cut-out it has to be...I'll have to check and see if I have a hole saw bit that size.

I not sure what you mean modify the rear tray, you can actually use any size speaker (woofer) in the center up to a 10". The grille will stay the same size obviously, but you can put any speaker behind it after cut the rear deck metal.

Thanks,

Dennis

[Nothingface5384]

Sounds good
as for the rear deck, i just ment are you able.to mold one without the current 2 round and 1 square recessed indent
and just have whole panel smooth with 1 outlined shape in center?
But i guess if i wrapped it in vinyl thatll take care of the issue anyways

[1976CamaroGuy]

I understand, it wouldn't be easy to do a smooth panel with the mold the way it is. Honestly with it being fiberglass you could actually fill in those speaker holes if you didn't want them.

Dennis

[OneslowZ28]

What is the time frame for the package tray?

[1976CamaroGuy]

I'd like to get four-five days to make and ship it, with the weekends being easier on me as I work through the week. I have to make a crate to ship that in too. Realistically if I got the payment tomorrow morning, I would start on it after work and should have it shipped by Friday. It also depends on if I have the supplies on hand, and I do at the moment.

Thanks,

Dennis

[1976CamaroGuy]

TTT - making kickpanels for a little bit right now

[1976CamaroGuy]

TTT one set of 70-81 Kickpanels available

[1976CamaroGuy]

..............

[1976CamaroGuy]

Ttt

[1976CamaroGuy]

bumpity bump

[1976CamaroGuy]

TTT, Have one set of 70-81 Kicks on hand right now

[1976CamaroGuy]

Bump it up

[1976CamaroGuy]

Ttt

[rreichert82]

TTT, Have one set of 70-81 Kicks on hand right now

Do you still have a set available? Also will these work on a Firebird with factory AC? If not do you still make the door pods?

[1976CamaroGuy]

Do you still have a set available? Also will these work on a Firebird with factory AC? If not do you still make the door pods?

I sold those, I can make another set if you want them. Yes they will fit factory ac, you need to cap off the fresh air vent flapper on the passenger kick and will lose that function. But the rest of the AC functions as normal.

Here's a set installed in a firebird BTW

https://static1.pt-content.com/images/pt/2015/09/20121022_161922_907_zps0jfnjl6o-1.jpg

[Hot1970Nova]

Anything for a 70 nova?

[1976CamaroGuy]

Anything for a 70 nova?

sorry I don't, just 1st and 2nd gen camaro

[rreichert82]

I sold those, I can make another set if you want them. Yes they will fit factory ac, you need to cap off the fresh air vent flapper on the passenger kick and will lose that function. But the rest of the AC functions as normal.

Here's a set installed in a firebird BTW

https://static1.pt-content.com/images/pt/2015/09/20121022_161922_907_zps0jfnjl6o-1.jpg

They look great. email me Robert.reichert82 @ Gmail and let me know how I can order a set.

[1976CamaroGuy]

They look great. email me Robert.reichert82 @ Gmail and let me know how I can order a set.

Sent ya a PM, my email is in there and same as my paypal addy. If you prefer to send a money order I can PM my address.

Thanks

Dennis

[oillie716]

I would like a set for a 67 chevelle let me know thankyou

[oillie716]

you can call me 315 876 4109 I want a set thankyou

[1976CamaroGuy]

I would like a set for a 67 chevelle let me know thankyou

sorry, I don't have anything for a 67 chevelle, Just 67-92 Camaro / firebird

[1976CamaroGuy]

TTT, gonna try and keep some stock from now until the Holidays, until gone. You can get them here for $165 shipped to lower 48 or ebay.

Here's the eBay link for the 70-81 kicks. There's some more pics there in the body of how they look and fit

http://www.ebay.com/itm/191702416020?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1558.l2649


https://static1.pt-content.com/images/pt/2011/04/file118_zpsdotto7hl-1.jpg

https://static1.pt-content.com/images/pt/2015/09/file117_zpsaqfpiics-1.jpg


Here's the 67-68 (69 with mods) speaker kicks

http://www.ebay.com/itm/191703072168?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1558.l2649

https://static1.pt-content.com/images/pt/2015/09/20150329201651572020Copy_zps1whtwo7i-1.jpg


What they look like if they are finished out (I only sell them in kit form)

https://static1.pt-content.com/images/pt/2015/09/2015052520111000_zpsxglo0sdh-1.jpg

[1976CamaroGuy]

I've got 3-4 sets of the 70-81 fibody speaker Kick panels and 4 sets of the 67-69 fbody speaker Kick panels to sell from now through holiday season. Boxed and ready to ship

$165 shipped for either set each to lower 48 states

Also have a couple of package trays too

[1976CamaroGuy]

TTT Still have some sets available.

Also on eBay

67-69 Speaker Kicks eBay # 191712977006

70-81 Speaker Kicks eBay # 191737232738

70-81 Package Tray eBay # 191711947290

[minendrews68]

Do you still have pics of mine installed? Might pop them on here if you do.
How's it going? Have any of that fiberglass left lol.......
Carl

[1976CamaroGuy]

I do still have your pics, I def need to throw them up. The 1st gens kicks can be a little bit of a hard sell. I may quit doing them after I sell this batch. They don't get snatched up as quick as the 70-81's do which is mind boggling with the amount of 1st gens out there

Going pretty good, still working on my car lol, I'll get it done sometime. I do have about a 1/2 of what fiberglass I started with left, but it's whittling down lol

[minendrews68]

1/2 of the big roll?

[1976CamaroGuy]

1/2 of the big roll? Yeah man, that's pretty thick fiberglass mat. Didn't take long to dwindle it down a bit.

[minendrews68]

Man, you've been busy!

[1976CamaroGuy]

yeah a little lol

[1976CamaroGuy]

sold out of 1st gen kicks

[1976CamaroGuy]

Ttt

[1976CamaroGuy]

Ttt

[1976CamaroGuy]

I have a set of 70-81 kicks on hand to sell at the moment

[radz28]

Can you PM me information on a set of kickpanels for a 71 camaro? Interested in ones but not sure if you have different sizes for speakers. Thanks AJ

[1976CamaroGuy]

Can you PM me information on a set of kickpanels for a 71 camaro? Interested in ones but not sure if you have different sizes for speakers. Thanks AJ

Hi AJ, They are for either a 6.5" and some 6.75" speakers depending on the grille size. As long as the grille isn't over 7" in dia they will work.

I sold a set I had on hand last Friday, but I have another set I need to finish up. I had planned on having them ready by the weekend. Just let me know

Thanks,

Dennis

[1976CamaroGuy]

Ttt

[1976CamaroGuy]

Ttt

[1976CamaroGuy]

Got several 2nd gen sets on hand right now

Got this message from a ebay member earlier, that made my day :-)

https://static1.pt-content.com/images/pt/2016/05/Untitled2_zpsilk9hpg6-1.jpg (http://s1310.photobucket.com/user/1971camaroguy/media/Untitled2_zpsilk9hpg6.jpg.html)

[1976CamaroGuy]

Have a couple sets of each on hand right now

[1976CamaroGuy]

TTT, have some sets on hand right now

[1976CamaroGuy]

I have a few sets FS

[Camaro68+69]

Are you making any 69 Camaro Rear Speaker Package trays?

thanks
Scott

[1976CamaroGuy]

Are you making any 69 Camaro Rear Speaker Package trays?

thanks
Scott

Hey Scott,

I'm not at this time, just the tray for the 70-81 Cars. I might in the future and thanks for asking

Dennis

[1976CamaroGuy]

9/13/16 I have on hand:

67-69 Camaro Speaker Kick Panels

70-81 Camaro Speaker Kick Panels

78-81 Camaro Speaker Door Pod

70-81 Camaro Speaker Package Tray

Boxed and ready to put a label on and ship

[Mofoe73]

Hello do you make these for 67 or 69 Chevelle?

[1976CamaroGuy]

sorry I don't, just what's listed

Thanks for asking

[1976CamaroGuy]

11/08/16 I have on hand:

67-69 Camaro Speaker Kick Panels

70-81 Camaro Speaker Kick Panels

78-81 Camaro Speaker Door Pod

70-81 Camaro Speaker Package Tray

82-92 Camaro Door Speaker pods

Boxed and ready to put a label on and ship

[1976CamaroGuy]

Bumpity Bump

[1976CamaroGuy]

I have two sets of 1st gen panels, and several 2nd gen panels available. And a few 2nd gen package trays too

[weircc]

Without reading through the hole thread on my phone lol. What the price of package tray for 2nd gen

[1976CamaroGuy]

Without reading through the hole thread on my phone lol. What the price of package tray for 2nd gen

$185 shipped to lower 48, I have two of them

[outragis]

does anyone know if the early Camaro ones will fit 68-72 Nova?

[1976CamaroGuy]

I had looked into this, and the 68-72 Nova shares a lot of design characteristics with the 1st gen and googling the kick panels they look identical.

Nova

https://static1.pt-content.com/images/pt/2016/12/9882391JPG-1.jpg

Camaro

https://static1.pt-content.com/images/pt/2016/12/8752667JPG-1.jpg


Since these use a pinch weld you have some wiggle room and can do some more precise trimming to fit.

But I can't tell you for sure, maybe someone else that has their hands on both cars can clarify it.

[1976CamaroGuy]

Have a set of 70-81 kicks, 78-81 Door pods, and a 70-81 Tray on hand right now

[1976CamaroGuy]

Have a set of 2nd gen kicks and a set of 1st gen speaker kicks on hand right now.....

[Brandon]

Dibs on the 2ng Gen Speaker Kicks! Do you have the 70-81 Camaro Speaker Package Tray avail. right now as well? Looking to buy the 2nd gen speaker kick panels and the package tray. Let me know. Paypal ready.

Brandon

[1976CamaroGuy]

Dibs on the 2ng Gen Speaker Kicks! Do you have the 70-81 Camaro Speaker Package Tray avail. right now as well? Looking to buy the 2nd gen speaker kick panels and the package tray. Let me know. Paypal ready.

Brandon

Hi Brandon,

Don't have any trays made up but planning on doing some more soon.

I do have a set of kicks ready to go, I'll PM my paypal info

[minendrews68]

Hey Dennis, I need to get with you and have you look at a fiberglass project i'm thinking about. Nothing too big though..

[hutchinaugusta]

i would like to see about a set of kick and package tray for a 73 firebird I am building

[1976CamaroGuy]

i would like to see about a set of kick and package tray for a 73 firebird I am building

I am done with the kick panels for now, I would have to re-tool the molds and I am busy with other things.

I do have two trays right now, can ship as early as monday on that

Thanks