PDA

View Full Version : 1969 Camaro Restomod Project Thread



will69camaro
03-11-2011, 08:30 AM
Finally getting around to putting a thread up on here. Been keeping it on a few other sites. It's just another 69 camaro so nothing to exciting or "innovating" for most out there. However, it is my first car and I'm building it the way I always wanted to. End goal is to have a fun car that I can drive anywhere, take on Power Tour and see some track time (both straight and turns).

9-8-2010:
Well finally got the urge to start working on the 69 again. Putting off any more work on the 2010 to start funneling cash towards my first car. I'm really excited about working on the car. I've picked up a few parts for it already (nothing too major).

Started today by putting the car on jack stands and taking off the stock hood. Stock hood will be replaced with a new steel cowl hood.
Started prepping to remove the 94 Z28 LT1/T56 setup. Motor has a new owner waiting for it, and the transmission is being sold to a co-working for swap into his 70 Chevelle SS.

Coming soon, I'll be removing the 10 year old MAACO paint job for something a little nicer. Car will be returned to Hugger Orange and plan to have the body completely refinished and all rust removed.

Also soon to come, picking up a 6.0L iron block later this week for a 408 build w/ L92 heads. Will be setting it up to be decent NA motor but plans to add boost in the future. Also may pick up a 12 bolt factory 69 rearend to build for this car to replace the 8.2" 10 bolt factory limited slip rearend. Already picked up a LS type T56 that has been rebuilt and comes with a Spec clutch (may/may not use, undecided).

Ultimately I would like this car to have full aftermarket suspension (ie front clip, 4 link, etc). For now I'm going to focus on getting the body work done, maybe get it mini-tubbed in the process, and get it running. I'll do suspension after it's running/driving. Easy enough to do and will let me enjoy the car about a year sooner for a while as I save up for the suspension.

Now on to the pics! Not much done today but car is still kinda cramped in the garage (working on making more room to work as well!)

In the garage with the 2010 SS:
https://static1.pt-content.com/images/pt/2011/03/999984712_BpqqPL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/999986980_quQzwL-1.jpg

Filthy LT1 setup (car has been parked for 5-6 years, most of which outside in west Texas):
https://static1.pt-content.com/images/pt/2011/03/999968189_KgPNnL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/999968530_x6jxaL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/999968328_YeeQxL-1.jpg

Few pics of the new parts I have for the car (T56, clutch, hood)
https://static1.pt-content.com/images/pt/2011/03/999986591_HkHukL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/999986879_HaW4YL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/999968051_7DxvVL-1.jpg

will69camaro
03-11-2011, 08:32 AM
9-8-2010:
Here are some misc pictures of the car showing the body damage and rust I'll be contesting!
Passenger Rear quarter panel:
https://static1.pt-content.com/images/pt/2011/03/999984808_qWHv6L-1.jpg
https://static1.pt-content.com/images/pt/2011/03/999984905_6kDNSL1-1.jpg
Driver Rear quarter panel:
https://static1.pt-content.com/images/pt/2011/03/999985180_ZQgXxL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/999985279_9DmZ8L1-1.jpg
Driver front fender/door:
https://static1.pt-content.com/images/pt/2011/03/999987681_afEuSL-1.jpg
Passenger front fender/door:
https://static1.pt-content.com/images/pt/2011/03/999987889_CHd4SL-1.jpg
Rearend/Exhaust:
https://static1.pt-content.com/images/pt/2011/03/999987233_JxjcfL-1.jpg
Interior:
https://static1.pt-content.com/images/pt/2011/03/999985498_bGHPBL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/999985652_7TjGaL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/999985762_FFiBSL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/999985865_yeqnTL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/999986129_pxT2dL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/999986013_QT7JoL-1.jpg

I will be updating this. Don't expect final results for quite some time but hope to use this thread for motivation/incentive to put the work in. Hoping to have the engine/trans out by the weekend and then I'll see if I'm going to strip it in the garage or have it media blasted/stripped by a shop.

William

will69camaro
03-11-2011, 08:33 AM
9-9-2010:
Mainly all I did today since engine/trans is about ready to be pulled is I reorganized the garage to make more room. Still have a few things to move around but there is plenty of space now compared to what there was.
https://static1.pt-content.com/images/pt/2011/03/1001596245_pyHsSL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1001596344_rvWXuL-1.jpg
Sorry it's still in the bag, I'll pull it out tomorrow for better pics. Picked up the 6.0L iron block machined to be a 408. Took a set of calipers with me and all appears to be good. I'll naturally have it checked out by a machinist to ensure all is ok. HKE did the work so I'll probably take it back there.
https://static1.pt-content.com/images/pt/2011/03/1001596536_qAfbhL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1001596077_XkeWiM-1.jpg

will69camaro
03-11-2011, 08:35 AM
9-10-2010:
Interior has been stripped and I started removing the guages before I started running out of light and time before dinner. I forgot the extent I went to when I did it the first time to make it quiet inside.

Pics:
Interior as was when I started
https://static1.pt-content.com/images/pt/2011/03/1002491492_uKSpYL-1.jpg
Seats pulled up. Carpet sunfaded red. Threw it away for new stuff.
https://static1.pt-content.com/images/pt/2011/03/1002491876_Gtei6L-1.jpg
Forgot I put down a 3/4" layer of "jute" under the carpet to sound deadening. I didn't remember doing this until I saw it LOL
https://static1.pt-content.com/images/pt/2011/03/1002492145_g7vj4L-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1002492288_HTBahL-1.jpg
This is how much of that stuff there was...Probably about 15-20lbs worth, maybe more but I dont have a scale.
https://static1.pt-content.com/images/pt/2011/03/1002493001_3pkG5L-1.jpg
Under that there was a thin layer of thermal insulation (water heater stuff). Not the best but on a college kid buget it wasn't bad. I had this stuff EVERYWHERE!
https://static1.pt-content.com/images/pt/2011/03/1002492461_GWTpVL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1002492641_hs48ZL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1002492899_Y3NZ3L-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1002492758_miyCBL-1.jpg
All of that was removed as well. There is residue left but it's not too bad.
https://static1.pt-content.com/images/pt/2011/03/1002493292_59QgBL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1002493121_dgx39L-1.jpg
Quick pic of how I left it today.
https://static1.pt-content.com/images/pt/2011/03/1002493669_XZB7AL-1.jpg
Here is the pile of parts that were removed. Carpet not shown as it was in the trash with the insulation.
https://static1.pt-content.com/images/pt/2011/03/1002493775_YAbu4L-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1002493897_YVgL4L-1.jpg

I'll have more pics tomorrow when the engine gets pulled.

William

will69camaro
03-11-2011, 08:37 AM
9-11-2010:
Went to Super Chevy at HRP and walked around/checked out the nice cars in the area. Swap meet brought me to the Camaro Country guys. Talked to them a bit and I think I'm going to take the car down there to get blasted. Also may have them do the quarters on the car. I'll check out their place when they blast it and maybe ask for some references to discuss with customers.

We got back from Super Chevy and decided to tear into the 69 even further. Burgers and beer later we got a good bit accomplished!
Front end coming apart. Grille removed, bumper removed and lower valence coming off.
https://static1.pt-content.com/images/pt/2011/03/1004002854_HiSyXL-1.jpg
Trunk and spoiler removed.
https://static1.pt-content.com/images/pt/2011/03/1004002991_HKC3kL-1.jpg
Bumper/lights removed.
https://static1.pt-content.com/images/pt/2011/03/1004003454_ZdMcqL-1.jpg
Engine is coming out!
https://static1.pt-content.com/images/pt/2011/03/1004004784_NUiGjL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1004004453_SH7WtL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1003957731_b2rgRL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1003958423_QprHAL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1003959151_fgwfvL-1.jpg

That's all we got done today. Was a FULL day. Tomorrow I got chores/etc to do, will try to clean up the garage and put the tools up that we used. Trans will get pulled off as it's sold, engine will get loaded up as it's sold as well. Going to keep taking panels off and then throw it all on a trailer/bed of the truck and take it to get it blasted.

William

will69camaro
03-11-2011, 08:40 AM
At this point I hit a stopping point. Work picked up and occupied all my time as it tends to do. Had to take a break from the car and focus on life for a bit. Ended up leaving my current employer and waiting to start with my new. That means I had about 3 weeks vacation!!! So on to more updates!

2-21-2011:
Didn't get the car to the blasting place today. Had to remove the exhaust, doors and get it on the trailer still. Got that all finished up today so it'll be dropped off first thing in the morning.

Friend of mine that has built a few of these already said it looks like a pretty solid car to start with. Quarter panels we know need work but pillars/pans/rockers/cowl, all look good. Rear window channel has a little damage but all will be replaced with the new quarter panel. We'll see if we still feel the same after the blast work.

Pics:
https://static1.pt-content.com/images/pt/2011/03/1194620374_Z4BiLXL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1194623639_2cd2DXL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1194625285_Tc8KEXL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1194627623_sSfw7XL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1194629315_PEuFEXL-1.jpg

More pics to come when the paint/bondo is off the car!

William

will69camaro
03-11-2011, 08:41 AM
So the camaro was gone, and I was bored...What to do...UPDATE THE GARAGE!!!

2-28-2011:
Sorry for the messy pics and plan to get better pics. Started to clean up camaro stuff and it got dark and it hit me...Garage needs more light!!!

Before:
https://static1.pt-content.com/images/pt/2011/03/1202216556_XJK3PL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202216643_Z5eSsL-1.jpg

As you can see it was dark at best with the 2 incandescent bulbs. I have 2 drop lights and some halogens on a stand (cheapies from Northern Tool). Not NEARLY enough light for a working space for the car hobby!

The lights to be installed:
https://static1.pt-content.com/images/pt/2011/03/1202217037_BgeLqL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202218375_3h599L-1.jpg

Lights are 1ft x 4ft fluorescent recessed fixtures each with 2 - T8 6500k bulbs. I picked up 9 of these lights, 3 for each car bay! Ended up spending quite a bit of cash on lighting and got to learn a lot about working with sheetrock and mounting for these guys. I think the results however are well worth the hassle (2 solid days in the garage hanging lights).

After:
https://static1.pt-content.com/images/pt/2011/03/1202223338_2N3mpL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202223551_mrPQgL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202218403_swYmxL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202220053_vgBarL-1.jpg

More pics to come when the garage is cleaned up a little more. It's VERY bright inside the garage. Back row of lights are on a separate switch so when it's daytime and the garage is open and the lights are blocked, they can be turned off. Front lights are far enough forward to light up the work bench and under the hood of the cars. Roof will be painted eventually, just not high on the priority.

William

will69camaro
03-11-2011, 08:44 AM
3-1-2011:
Went to see the car at Enviro Cleaning today all blasted inside and out.

I'll put up some teasers before getting into any details.
https://static1.pt-content.com/images/pt/2011/03/1202234699_2JuBmL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202236295_AkXDrL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202236335_KPNP9L-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202254695_CeGPFL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202256915_XcXEQL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202258623_7HfGcL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202260552_xmAkaL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202260798_Lun3yL-1.jpg

That's all for now. I can get into specifics later on areas of concern. Obviously you can tell (and as I suspected) quarter panels are "rough." Few surprises like small rust bubbles (common areas just didn't see it) in the roof cap on windshield channel, and down by the vin on the sealing surface of the front window. Both areas are very small but still should be address and patched at the very least. Bottoms of the front fenders need some patch work and the doors need some patch work. Trunk lid will need to be replaced.

William

will69camaro
03-11-2011, 08:45 AM
3-4-2011:
Got a call around 10am saying the body of the car has been primed. They were working on fenders and small pieces. No call to pick it up yet so I'll plan on picking it up Monday. That's ok as I have some more work to do in the garage getting it ready for the car/project.

Here are a few detailed shots to hold you guys over until I get the primed pictures.
Tail Panel:
Showing most the bondo on panel.
https://static1.pt-content.com/images/pt/2011/03/1202234736_hmZ5oL-1.jpg
Small tear behind bumper and line of rust.
https://static1.pt-content.com/images/pt/2011/03/1202234791_gudFxL-1.jpg
Showing the bondo on the lower valence.
https://static1.pt-content.com/images/pt/2011/03/1202239464_XhUb4L-1.jpg

Passenger Quarter Panel:
Worst panel on the car.
https://static1.pt-content.com/images/pt/2011/03/1202237761_UbXwYL-1.jpg
Top of the wheel well rust (could see this through paint).
https://static1.pt-content.com/images/pt/2011/03/1202238023_y8YK4L-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202254731_JNZEYL-1.jpg
Split quarter just in front of the rear wheel.
https://static1.pt-content.com/images/pt/2011/03/1202256676_eytDvL-1.jpg
Window channel on passenger quarter.
https://static1.pt-content.com/images/pt/2011/03/1202238039_kTGn2L-1.jpg
Rust in the trunk area on passenger side.
https://static1.pt-content.com/images/pt/2011/03/1202252924_QzbiHL-1.jpg

Driver Quarter Panel:
Bondo in weird places.
https://static1.pt-content.com/images/pt/2011/03/1202245966_JJrnSL-1.jpg
Small amount of rust above the wheel well. Not as bad as the other side.
https://static1.pt-content.com/images/pt/2011/03/1202240954_fDFT6L-1.jpg
Small amount of rust in front of rear wheel.
https://static1.pt-content.com/images/pt/2011/03/1202241284_2stjpL-1.jpg
Rust in the seam between the quarter panel and the panel above the trunk below the rear windshield.
https://static1.pt-content.com/images/pt/2011/03/1202239664_yRRYtL-1.jpg

will69camaro
03-11-2011, 08:46 AM
3-4-2011:
Passenger Side Door:
Very little rust in this panel.
https://static1.pt-content.com/images/pt/2011/03/1202256915_XcXEQL-1.jpg
Looking at the bottom right of the panel above, you can see this small spot of rust.
https://static1.pt-content.com/images/pt/2011/03/1202256912_FEfFiL-1.jpg

Driver Side Door:
Little more rust but not terrible. Will be patched.
https://static1.pt-content.com/images/pt/2011/03/1202258623_7HfGcL-1.jpg
Previously filled side mirror hole. Will be punched out and mirror installed.
https://static1.pt-content.com/images/pt/2011/03/1202258857_Rz4BML-1.jpg
Rust in bottom front corner (similar place as other side).
https://static1.pt-content.com/images/pt/2011/03/1202258858_2JC87L-1.jpg
Leading edge of the door hit the fender (misaligned). Will be fixed.
https://static1.pt-content.com/images/pt/2011/03/1202262596_cN2rDL-1.jpg

Passenger Front Fender:
Looks pretty good, had a dent pulled out in the past, will be patched.
https://static1.pt-content.com/images/pt/2011/03/1202260552_xmAkaL-1.jpg
Closeup of the bondo repair work on lower side behind wheel.
https://static1.pt-content.com/images/pt/2011/03/1202260841_oARUmL-1.jpg

Driver Front Fender:
Little rust but again it will be patched.
https://static1.pt-content.com/images/pt/2011/03/1202260798_Lun3yL-1.jpg
Closeup of the rust on the lower section behind the wheel.
https://static1.pt-content.com/images/pt/2011/03/1202262379_Kjc2SL-1.jpg

Dash:
Cant find the pic but it has a nickel size rust spot on the dash sealing area for the front windshield below the vin. It will get patched.

Roof:
Pretty good shape, little rust in the window channel and some surface rust/dents. Will be patched where necessary.
https://static1.pt-content.com/images/pt/2011/03/1202244044_dKNqkL-1.jpg
Front window channel (approx 1ft from passenger a-pillar).
https://static1.pt-content.com/images/pt/2011/03/1202244127_ZCJnCL-1.jpg
Closeup of the same spot showing a small spot of rust.
https://static1.pt-content.com/images/pt/2011/03/1202244094_iNfA6L-1.jpg

will69camaro
03-11-2011, 08:47 AM
3-4-2011:
Floors and rocker panels:
Overall very good shape. Small patches in rear floor near the drains to fix pin hole rust (not bad)
Passenger side rear floor drain.
https://static1.pt-content.com/images/pt/2011/03/1202242410_PDLRTL-1.jpg
Driver side rear floor drain.
https://static1.pt-content.com/images/pt/2011/03/1202242410_PDLRTL-1.jpg
Driver side rocker panel. SOLID.
https://static1.pt-content.com/images/pt/2011/03/1202249425_p4ZmnL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202249330_gf6F5L-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202247830_DJPLML-1.jpg
Passenger side rocker panel. SOLID.
https://static1.pt-content.com/images/pt/2011/03/1202251116_T9n82L-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202251094_bmMFNL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202251184_d7BW5L-1.jpg
Hole in trunk pan for previously modified tank (patching and going different route).
https://static1.pt-content.com/images/pt/2011/03/1202252954_bD2vmL-1.jpg
No pics after blasting but shifter hole(s) will be patched with an auto tunnel panel and will cut a single hole for T56.

Trunk lid:
This will be replaced. LOTS of bondo on it.
https://static1.pt-content.com/images/pt/2011/03/1202242714_pZLmUL-1.jpg

Header panel:
Looks good, no dents, rust, etc.
https://static1.pt-content.com/images/pt/2011/03/1202264043_9ZB9wL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202264277_xbxRwL-1.jpg

Front Valence:
No rust, but a few small dents that will need to be fixed.
https://static1.pt-content.com/images/pt/2011/03/1202262761_32EKQL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202263863_5LDwhL-1.jpg
https://static1.pt-content.com/images/pt/2011/03/1202265090_UfDYaL-1.jpg

Vent panel:
No pics (can be seen in some of the above), but all is good. No real rust or dents.

That's all the detailed updates I can give for now.

William

will69camaro
03-11-2011, 08:52 AM
That brings us up to date on the project.

Putting in an order today for all the sheet metal I will be needing on the project. Trying to split up the orders into specific groups/sections to track costs on the project and keep the flow of the project going. Right now goal is the body work. Probably going to make a gantt chart for the project is MS project to try and track milestones and expected dates. Part of being in project management in my working life I guess.

Ultimate goal for right now is to have the body work completed by end of summer. While the car is at the body shop I will build the 408 and have it prepped for the cars return. After body work I'll begin the interior renovations. After that will be suspension, wheels, tires, brakes. HOPING to have the car done by Power Tour 2012. Time will tell!!!

William

Bullockracing
03-11-2011, 05:29 PM
Wow, that's a lot of change for one page!!! Love the updates to the garage, btw. I keep building my dream garage in my mind, and now I've added recessed lights!!!

bonecrrusher
03-12-2011, 06:28 AM
I see your now here and Lat-G... nice!

Tucks69
03-12-2011, 07:05 AM
Cool Project! Keep us updated.

will69camaro
04-01-2011, 09:49 PM
Update for pics. Picked up the rearend today. Couldn't wait until tomorrow. Guy was thinking about keeping it but lots of folding green changed his mind :)

https://static1.pt-content.com/images/pt/2011/04/1236609366_mS7DnL-1.jpg

https://static1.pt-content.com/images/pt/2011/04/1236608883_zjEJHL-1.jpg

https://static1.pt-content.com/images/pt/2011/04/1236610036_8Eyy3L-1.jpg

Quadralink (4 link) brackets already welded on already.
https://static1.pt-content.com/images/pt/2011/04/1236611807_6z6HFL-1.jpg

Interesting question however. Guy gave me the coilovers with the rearend. They have a DSE part number on the spring. However in my research I see that DSE offers a revalved QA1 as the shock choice. Also upon further observation, I see that the shocks appear to be front shocks that DSE used to sell.

Anyone have an insight on this? I'm ok with it as I got a good enough deal on it all to justify buying new coilovers if I need to, just interesting that it has what appears to be front shocks that came with it. I got it from a guy who bought it from the original purchaser. A twice hand me down 9" that has never been run...

Details are 54.75" width, 31 spline axles, ford tru-trac diff and 4.10 gears. Is powder coated gloss black and has the moser "N" spec center section.

William

will69camaro
12-23-2014, 08:47 AM
https://static1.pt-content.com/images/pt/2014/12/TYPVhcd-1.jpg

Thread gravedigger.

will69camaro
03-21-2016, 02:08 PM
TTT

https://static1.pt-content.com/images/pt/2016/03/SSJNvxQ-1.jpg

ICrombie
03-21-2016, 02:20 PM
Wow! That looks fantastic, I really like completely smooth firewall and of course those twin turbos ahah.

will69camaro
03-21-2016, 02:22 PM
Yea firewall came out very nice. Happy I went this route with the clutch/brake pedal assembly. Really compliments the engine I think.

It will fill up some once i start putting in the PCV/Breather tank/etc but should still be pretty "clean."

https://static1.pt-content.com/images/pt/2016/03/MJ7fv3n-1.jpg

https://static1.pt-content.com/images/pt/2016/03/a6B9BXi-1.jpg

https://static1.pt-content.com/images/pt/2016/03/VcKWSnl-1.jpg

will69camaro
09-10-2016, 12:32 PM
Got it out again today. Clutch pedal adjusted. Diff leak fixed. And raised front so it can turn. Pretty close to first official drive.

https://static1.pt-content.com/images/pt/2016/09/rMzAfee-1.jpg

https://static1.pt-content.com/images/pt/2016/09/mAexH1u-1.jpg

It's ready to come out and play!
https://static1.pt-content.com/images/pt/2016/09/WgXiw7r-1.jpg

Stance is about as good as it'll get.
https://static1.pt-content.com/images/pt/2016/09/rjj5QOm-1.jpg

https://static1.pt-content.com/images/pt/2016/09/SC6S6sG-1.jpg

https://static1.pt-content.com/images/pt/2016/09/8v2cUMw-1.jpg

Got the cooling system bled also so it ran for 15 min and got to 190deg and stabilized. Pretty happy with that. We'll see how it does when it's driven.

will69camaro
10-03-2016, 10:53 AM
https://www.youtube.com/watch?v=ssgXqe2nhZc

minendrews68
10-06-2016, 06:08 PM
That's funny, not a window one in the car! I got impatient and did the very same thing !

icemanrd19
10-06-2016, 06:14 PM
where did you mount your coil packs and how

will69camaro
10-07-2016, 10:33 AM
That's funny, not a window one in the car! I got impatient and did the very same thing !

I couldn't help myself.


where did you mount your coil packs and how

They're on the firewall inside the fender. Where the blower motor was factory. Rivsert to the firewall.

https://static1.pt-content.com/images/pt/2016/10/BRZw1O9-1.jpg