ed1le
02-04-2011, 07:23 AM
SOLD-355 – 010 casting, 2-bolt main
Hypereutectic Flat tops, Powerhouse remanufactured small valve heads
Crane cam
Crane Blazer 1.5 roller rockers
Edelbrock RPM intake
Noisy Gear Drive
Edelbrock 2-piece aluminum timing cover
7qt deep sump oil pan & hi-volume oil pump
Billet tall valve covers & water neck
New stock long water pump
Under 500 miles on engine. My buddy built this a few years ago for his daily driver but sold the car before installing it. It was installed in his brothers truck for break-in and driven locally a few times but that was it. I bought it off him and installed it in my Skylark but never fired it. Buying an LT1 so it needs to go. I have kept it oiled and turned it over by hand regularly to keep it lubed. Don't recall cam specs but in the 220/.460 range I believe. I do know he was shooting for 300hp & 375ft lb and is very meticulous w/ his builds. asking $600-SOLD
https://static1.pt-content.com/images/pt/2011/02/101_1946-1.jpg
https://static1.pt-content.com/images/pt/2011/02/101_1947-1.jpg
(old edelbrocks on it now were just to make sure the good ones didn't get scratched when installing)
https://static1.pt-content.com/images/pt/2011/02/DSC02396-1.jpg
Centerforce flywheel, #CTF-700107 for t56/2-piece sbc
Bought w/ approx. 8K miles (I believe from someone on here or LS1tech.com), I had it resurfaced, hasn't been used since. Retails for $410, asking $300
https://static1.pt-content.com/images/pt/2011/02/101_1950-1.jpg
Summit 600 carburetor - New, installed but never run. Still have box & everything that goes with it (cost $260). (ProComp billet spring/cable bracket & Spectre dual feed fuel line w/ gauge are sold) asking $225
https://static1.pt-content.com/images/pt/2011/02/101_1944-1.jpg https://static1.pt-content.com/images/pt/2011/02/101_1945-1.jpg https://static1.pt-content.com/images/pt/2011/02/101_1949-1.jpg
SOLD-Summit 100 amp 1-wire alternator, powder coated black w/ Summit billet brackets - New, alt was $80 & brackets were $40, asking $80-SOLD
https://static1.pt-content.com/images/pt/2011/02/101_1941-1.jpg
-SOLD-Type II P/S pump w/ reservoir w/ brackets & aluminum pulley - pump is new, brackets & pulley have some nicks but probably from sitting around, bracket missing a couple bolts as well but nothing you couldn't get from a hardware store. Pump alone retails for $150 and Summit has bracket for $110 bought last month from someone on LateralG.net for $150, for use w/ long pump, asking $150-SOLD
https://static1.pt-content.com/images/pt/2011/02/101_1936-1.jpg
SOLD Summit Billet water pump (single groove-$36 retail) and Crank (double groove- $50 retail) pulleys - new, asking $50 SOLD
https://static1.pt-content.com/images/pt/2011/02/101_1942-1.jpg
SOLD-Summit billet water pump (double groove-$50 retail) and Crank (triple groove-$53 retail) pulleys –new, asking $50-SOLD
https://static1.pt-content.com/images/pt/2011/02/101_1937-1.jpg
SOLD-Jegs mechanical fuel pump (80gph) - new, installed on engine but never run, cost $50, asking $30-SOLD
https://static1.pt-content.com/images/pt/2011/02/101_1939-1.jpg
SOLD-Procomp HEI w/ coil & cap - new, cost around $100, asking $75-SOLD
https://static1.pt-content.com/images/pt/2011/02/101_1951-1.jpg
Will post pics of everything tonight. Prices DON'T include shipping. Thanks.
Hypereutectic Flat tops, Powerhouse remanufactured small valve heads
Crane cam
Crane Blazer 1.5 roller rockers
Edelbrock RPM intake
Noisy Gear Drive
Edelbrock 2-piece aluminum timing cover
7qt deep sump oil pan & hi-volume oil pump
Billet tall valve covers & water neck
New stock long water pump
Under 500 miles on engine. My buddy built this a few years ago for his daily driver but sold the car before installing it. It was installed in his brothers truck for break-in and driven locally a few times but that was it. I bought it off him and installed it in my Skylark but never fired it. Buying an LT1 so it needs to go. I have kept it oiled and turned it over by hand regularly to keep it lubed. Don't recall cam specs but in the 220/.460 range I believe. I do know he was shooting for 300hp & 375ft lb and is very meticulous w/ his builds. asking $600-SOLD
https://static1.pt-content.com/images/pt/2011/02/101_1946-1.jpg
https://static1.pt-content.com/images/pt/2011/02/101_1947-1.jpg
(old edelbrocks on it now were just to make sure the good ones didn't get scratched when installing)
https://static1.pt-content.com/images/pt/2011/02/DSC02396-1.jpg
Centerforce flywheel, #CTF-700107 for t56/2-piece sbc
Bought w/ approx. 8K miles (I believe from someone on here or LS1tech.com), I had it resurfaced, hasn't been used since. Retails for $410, asking $300
https://static1.pt-content.com/images/pt/2011/02/101_1950-1.jpg
Summit 600 carburetor - New, installed but never run. Still have box & everything that goes with it (cost $260). (ProComp billet spring/cable bracket & Spectre dual feed fuel line w/ gauge are sold) asking $225
https://static1.pt-content.com/images/pt/2011/02/101_1944-1.jpg https://static1.pt-content.com/images/pt/2011/02/101_1945-1.jpg https://static1.pt-content.com/images/pt/2011/02/101_1949-1.jpg
SOLD-Summit 100 amp 1-wire alternator, powder coated black w/ Summit billet brackets - New, alt was $80 & brackets were $40, asking $80-SOLD
https://static1.pt-content.com/images/pt/2011/02/101_1941-1.jpg
-SOLD-Type II P/S pump w/ reservoir w/ brackets & aluminum pulley - pump is new, brackets & pulley have some nicks but probably from sitting around, bracket missing a couple bolts as well but nothing you couldn't get from a hardware store. Pump alone retails for $150 and Summit has bracket for $110 bought last month from someone on LateralG.net for $150, for use w/ long pump, asking $150-SOLD
https://static1.pt-content.com/images/pt/2011/02/101_1936-1.jpg
SOLD Summit Billet water pump (single groove-$36 retail) and Crank (double groove- $50 retail) pulleys - new, asking $50 SOLD
https://static1.pt-content.com/images/pt/2011/02/101_1942-1.jpg
SOLD-Summit billet water pump (double groove-$50 retail) and Crank (triple groove-$53 retail) pulleys –new, asking $50-SOLD
https://static1.pt-content.com/images/pt/2011/02/101_1937-1.jpg
SOLD-Jegs mechanical fuel pump (80gph) - new, installed on engine but never run, cost $50, asking $30-SOLD
https://static1.pt-content.com/images/pt/2011/02/101_1939-1.jpg
SOLD-Procomp HEI w/ coil & cap - new, cost around $100, asking $75-SOLD
https://static1.pt-content.com/images/pt/2011/02/101_1951-1.jpg
Will post pics of everything tonight. Prices DON'T include shipping. Thanks.