View Full Version : Eddie Motorsports Billet Valve Covers
Mr. Hinge
03-04-2010, 11:15 AM
We're not just about hinges. We can make other stuff too. Here's an LS1 Valve Cover that came off the machine this morning. We will also make them with breathers and coil mounts. Comments and suggestions are welcomed. Made in Rancho Cucamonga, USA!
https://static1.pt-content.com/images/pt/2010/03/EMSLS1COVER2-1.jpg
1badchevelle
03-04-2010, 12:49 PM
Dam those are nice. What the damage on a set?
CruizinKev
03-04-2010, 01:26 PM
sweet! very nice! :twothumbs
Mr. Hinge
03-04-2010, 02:40 PM
Dam those are nice. What the damage on a set?
We still have to make spacers for the screws and order some o-rings. Then we will have a price. They will be priced right...
Thanks!
beep4beep
03-04-2010, 07:32 PM
are you guys goinging to get around to making b body mopar hinges? beep4beep Randy
Mr. Hinge
03-05-2010, 07:35 AM
are you guys goinging to get around to making b body mopar hinges? beep4beep Randy
Yes. We have at least one hinge in line before the Mopar.
Thanks,
wellis77
03-05-2010, 09:57 AM
A set of Gen 3 Hemi valve covers wouldn't be all bad either...
mpozzi
03-05-2010, 10:07 AM
Plus that "Made in the USA" part makes this buying decision a bit easier. I've been looking at the origin of parts a lot closer in the past few years ...
These look great.
Cheers,
Mary Pozzi
Damn True
03-05-2010, 10:14 AM
We're not just about hinges. We can make other stuff too. Here's an LS1 Valve Cover that came off the machine this morning. We will also make them with breathers and coil mounts. Comments and suggestions are welcomed. Made in Rancho Cucamonga, USA!
https://static1.pt-content.com/images/pt/2010/03/EMSLS1COVER2-1.jpg
If I might suggest...how about a threaded bung instead of the push in breather port?
Mr. Hinge
03-05-2010, 10:44 AM
If I might suggest...how about a threaded bung instead of the push in breather port?
Actually, the large hole you see there is for the oil fill. I'll note a threaded bung for the breather.
Thanks!
monza
03-05-2010, 11:08 AM
Actually, the large hole you see there is for the oil fill. I'll note a threaded bung for the breather.
Thanks!
Maybe a locking oil fill cap option? Been there lost that on the track. (Optima two yrs. ago)
Mr. Hinge
03-05-2010, 11:42 AM
Maybe a locking oil fill cap option? Been there lost that on the track. (Optima two yrs. ago)
Got it!
bulldog19
03-06-2010, 03:13 AM
Very nice! Any plans for valve covers for non LS small block valve covers?
rjsjea
03-07-2010, 01:13 PM
A set of Gen 3 Hemi valve covers wouldn't be all bad either...
x2.....:smoke:
Mr. Hinge
03-08-2010, 07:18 AM
Very nice! Any plans for valve covers for non LS small block valve covers?
Working on the SBC right now...
Mr. Hinge
03-10-2010, 07:35 AM
Update on pricing per set...
LS1 Low Profile Machined: $385
LS1 Low Profile Polished: $430
LS1 Tall Profile Machined: $430
LS1 Tall Profile Polished: $480
Thanks,
Mr. Hinge
03-12-2010, 10:58 AM
Very nice! Any plans for valve covers for non LS small block valve covers?
Here they are! Billet Small Block Chevy Valve Covers. Still working on pricing...
https://static1.pt-content.com/images/pt/2010/03/EMSSBCCOVER-1.jpg
billyrb
03-17-2010, 06:39 PM
what about a center-bolt LT style with a flat top that can have a builder's name engraved? ;)
Here they are! Billet Small Block Chevy Valve Covers. Still working on pricing...
https://static1.pt-content.com/images/pt/2010/03/EMSSBCCOVER-1.jpg
damn you mister Hinge! Damn you!!!! :throw: I need my cars name cut into them and they need to be taller I have roller rockers!
Damn! Damn! Damn!
Whistler
03-17-2010, 10:21 PM
Very nice stuff! The LS covers are now on my wish list.
protouring70
03-19-2010, 03:58 AM
very clean looking
Mr. Hinge
04-12-2010, 12:15 PM
Here's a shot of our low profile LS1 Billet Valve Cover with a machined finish. Prices starting at $385/set.
https://static1.pt-content.com/images/pt/2010/04/ls1low1Small-1.jpg
Powered by vBulletin®