Camaro Zach
12-04-2004, 06:18 PM
Hello everyone, do you guys think this is a pretty good deal for under $4,500 bucks? Im thinking about building a motor similar to this or getting this one:
489 hp @ 6300 RPM 468 ft. lbs torque
Select Hi Tin block 2 bolt main machined 030
Power Making Featured Parts
• ALL NEW CANFIELD A EAGLE STEEL CRANK 3.75 STROKER crank with superior wear sized and indexed.499.00 SEALED POWER PISTON SETS HYPERUTECTIC 10.2 TO 1 PUMP GAS WITH ALUM HEADS OK
• Childs & Albert - zz gapdura Moly File Fit Rings...
• Durabond - cam bearings...
• GM I-BEAM FORGED RODS
• ARP - wavelock - rod bolts...
• Clevite- -bearings tri metal 77 - rod and main... custom hi output cam lifter set ..
• Cloyes - true roller set..
• Comp - cams cam locks...
• comp cams xe chrome moly pushrods
• Dyna gear race - oil pump...
• Dyna gear - pickup...
• ARP - steel drive...
• After market - oil pan. baffeld 7 qt BAFFLED WITH SPECIAL OIL CONTROL AND TRAP DOORS LOW GROUND CLEARANCE
• After market - timing cover...
• pioneer/arp - head bolts...
• ARP/ - rocker studs 3/8...
• Fel Pro blue - gasket sets...
• LUM HEADS 200CC RUNNERS WITH POWER MAKING FEATURES!!. Bowls blended,full ...
o Features - - -severe duty 2.08/1.60 valves plus ... 1.45 springs 10 degree super locks comp cam parts..good porting..7/16studs guide plates.gasket match p.c seals.chrome moly retainers[with race port work these heads are better than ANY OUT BOX HEADS YOU COULD PUT ON FROM SAME MANUFACTURE
• hi perfromance roller rockers-1.5 ratio...
o comp cams or custom series- - cam PLUS MATCHING INTAKES POLISHED
• Features - 108 center line 568 - 568 lift corrected 1.5 ratio = 568/568 lift. 248/248 dur @ 050 awesome power range . lopey muscle car idle. 80% streetable and will run vacum access with canister this is custom for the engine and is very street feindly for power output
Total parts 6676.00and labor value 2800 = $9475 average retail cost YOUR LOW PRICE FOR 406 CU IN OF 4495 A 2400 SAVINGS!!!! 1 ONLY AVAILBLE,CAM CAN BE CANGED TO CUSTOMERS SPECS NO CHARGE FOR SAME TYPE OF CAM. SOLD LESS CARB AND DIST
Thanks,
Zach
489 hp @ 6300 RPM 468 ft. lbs torque
Select Hi Tin block 2 bolt main machined 030
Power Making Featured Parts
• ALL NEW CANFIELD A EAGLE STEEL CRANK 3.75 STROKER crank with superior wear sized and indexed.499.00 SEALED POWER PISTON SETS HYPERUTECTIC 10.2 TO 1 PUMP GAS WITH ALUM HEADS OK
• Childs & Albert - zz gapdura Moly File Fit Rings...
• Durabond - cam bearings...
• GM I-BEAM FORGED RODS
• ARP - wavelock - rod bolts...
• Clevite- -bearings tri metal 77 - rod and main... custom hi output cam lifter set ..
• Cloyes - true roller set..
• Comp - cams cam locks...
• comp cams xe chrome moly pushrods
• Dyna gear race - oil pump...
• Dyna gear - pickup...
• ARP - steel drive...
• After market - oil pan. baffeld 7 qt BAFFLED WITH SPECIAL OIL CONTROL AND TRAP DOORS LOW GROUND CLEARANCE
• After market - timing cover...
• pioneer/arp - head bolts...
• ARP/ - rocker studs 3/8...
• Fel Pro blue - gasket sets...
• LUM HEADS 200CC RUNNERS WITH POWER MAKING FEATURES!!. Bowls blended,full ...
o Features - - -severe duty 2.08/1.60 valves plus ... 1.45 springs 10 degree super locks comp cam parts..good porting..7/16studs guide plates.gasket match p.c seals.chrome moly retainers[with race port work these heads are better than ANY OUT BOX HEADS YOU COULD PUT ON FROM SAME MANUFACTURE
• hi perfromance roller rockers-1.5 ratio...
o comp cams or custom series- - cam PLUS MATCHING INTAKES POLISHED
• Features - 108 center line 568 - 568 lift corrected 1.5 ratio = 568/568 lift. 248/248 dur @ 050 awesome power range . lopey muscle car idle. 80% streetable and will run vacum access with canister this is custom for the engine and is very street feindly for power output
Total parts 6676.00and labor value 2800 = $9475 average retail cost YOUR LOW PRICE FOR 406 CU IN OF 4495 A 2400 SAVINGS!!!! 1 ONLY AVAILBLE,CAM CAN BE CANGED TO CUSTOMERS SPECS NO CHARGE FOR SAME TYPE OF CAM. SOLD LESS CARB AND DIST
Thanks,
Zach