wally_245
03-07-2022, 02:19 PM
I have a 68 Camaro I have been somewhat working on for years, I bought it in 1993, but really haven't done much with it, other than collect parts, and I have a _LOT_ of parts.
It is a factory 275hp 327 4spd car with a 12 bolt, I have the GM of Canada Historical sheet with it.
My "Build" thread is here...
https://www.pro-touring.com/threads/95615-My-68-Camaro-Build?highlight=
It has a lot of bondo in the quarters, and has had some questionable work done to it at some point (I can tell their is some braze welds on the inside of the quarter).
It currently has a 5.3LS in it with a 4L60e, but to be honest that motor probably needs to be gone through, as I installed it in 2016, and it hasn't been touched since. It does have some stainless headers installed.
Like I said, I have a TON of parts mostly still new in box....
Ride-Tech Tru-turn (bought off someone on here)
Speedtech Chicane upper mounts (new)
SPC Upper control Arms (new)
Speedtech lower control arms (new)
Ride-Tech triple adjustable coilovers for Chicane (bought off someone on here)
Ride-Tech spindles (new)
Willwood hubs (new)
Brake brackets for CTS-V brakes (new)
CTS-V brakes (front and rear) (used off eBay, very clean)
EBC Yellow Pads for above (new)
Corvette Wagon Wheel rims with new Nitto rubber
Flowmaster exhaust kit
Flowtech stainless headers
Billet Aluminum Grill (was going to black it out except for the front of the bars)
Corbeau Seats (need recovering, and some foam)
Budnik Chicane steering wheel (red/alum)
GM Fbody Pan
Holly front mount accessory kit
Rebuilt 205A alternator
Tanks Inc Notched Gas Tank
Aeromotive Dual in tank pump kit
Aeromotive Fuel Pressure Regulator
Stainless hardware kit, some of it is already installed
DSE Firewall blockoff plate
Some _OPTIONAL_ stuff would be....
Lunati LS Crank (4.00" stroke, iirc) (new)
Twin 88mm CX Racing turbos (new)
Tial BOV (new)
Jenvey Cross-Ram ITB Intake (gorgeous intake)
K2 rods
AFR Mongoose Heads (new)
(I was going to build a twin turbo 454 LS, with the Chevy HP Block, so I have most of that, other than the pistons and the block)
The car is a roller.
I am sure I am missing a bunch of stuff. I will add to it if I think of anything.
I also have a 59 GMC Pickup that I am thinking of selling, it's got a custom 3 link in the back, with a 9" and QA1 mod-shocks. 2nd Gen Camaro front clip with a full Hotchkis front setup and C5 brakes/hubs.
The reason I am thinking of selling is to get a C2 Corvette (my dream car), and my wife won't let me have three project cars ;)
I honestly don't know what to ask, I have over $20k just in parts, so I would probably be looking at high $20's, but I am open to offers.
The truck would be around $15k.
Located in Thousand Oaks, CA
- - - Updated - - -
Oh, it has a Flaming River Tilt column installed as well.
It is a factory 275hp 327 4spd car with a 12 bolt, I have the GM of Canada Historical sheet with it.
My "Build" thread is here...
https://www.pro-touring.com/threads/95615-My-68-Camaro-Build?highlight=
It has a lot of bondo in the quarters, and has had some questionable work done to it at some point (I can tell their is some braze welds on the inside of the quarter).
It currently has a 5.3LS in it with a 4L60e, but to be honest that motor probably needs to be gone through, as I installed it in 2016, and it hasn't been touched since. It does have some stainless headers installed.
Like I said, I have a TON of parts mostly still new in box....
Ride-Tech Tru-turn (bought off someone on here)
Speedtech Chicane upper mounts (new)
SPC Upper control Arms (new)
Speedtech lower control arms (new)
Ride-Tech triple adjustable coilovers for Chicane (bought off someone on here)
Ride-Tech spindles (new)
Willwood hubs (new)
Brake brackets for CTS-V brakes (new)
CTS-V brakes (front and rear) (used off eBay, very clean)
EBC Yellow Pads for above (new)
Corvette Wagon Wheel rims with new Nitto rubber
Flowmaster exhaust kit
Flowtech stainless headers
Billet Aluminum Grill (was going to black it out except for the front of the bars)
Corbeau Seats (need recovering, and some foam)
Budnik Chicane steering wheel (red/alum)
GM Fbody Pan
Holly front mount accessory kit
Rebuilt 205A alternator
Tanks Inc Notched Gas Tank
Aeromotive Dual in tank pump kit
Aeromotive Fuel Pressure Regulator
Stainless hardware kit, some of it is already installed
DSE Firewall blockoff plate
Some _OPTIONAL_ stuff would be....
Lunati LS Crank (4.00" stroke, iirc) (new)
Twin 88mm CX Racing turbos (new)
Tial BOV (new)
Jenvey Cross-Ram ITB Intake (gorgeous intake)
K2 rods
AFR Mongoose Heads (new)
(I was going to build a twin turbo 454 LS, with the Chevy HP Block, so I have most of that, other than the pistons and the block)
The car is a roller.
I am sure I am missing a bunch of stuff. I will add to it if I think of anything.
I also have a 59 GMC Pickup that I am thinking of selling, it's got a custom 3 link in the back, with a 9" and QA1 mod-shocks. 2nd Gen Camaro front clip with a full Hotchkis front setup and C5 brakes/hubs.
The reason I am thinking of selling is to get a C2 Corvette (my dream car), and my wife won't let me have three project cars ;)
I honestly don't know what to ask, I have over $20k just in parts, so I would probably be looking at high $20's, but I am open to offers.
The truck would be around $15k.
Located in Thousand Oaks, CA
- - - Updated - - -
Oh, it has a Flaming River Tilt column installed as well.