Activity Stream
-
Older Activity
-
1 Minute AgoTmicallef replied to a thread 1967 Chevelle Pro-touring stance suggestions in Open (Pro-Touring) DiscussionThanks Splatt. When I first bought the car I thought that at the very least a front disc upgrade was needed but this car is set up with a 12"...4 replies | 217 view(s) -
33 Minutes Agoraustinss replied to a thread Drive Line Angles on Lowered 1968 LeMans (A-Body) in General Drive Train TechX2 Andrew knows his stuff2 replies | 77 view(s)
-
40 Minutes AgoThinking about this a little the blue park wire is likely not an input, it is an output from the wiper motor. It powers the high or low inputs until...5 replies | 297 view(s) -
1 Hour AgoMy 69 making quick progress2 replies | 369 view(s) -
3 Hours Agoclassiccarcustoms replied to a thread Rain gear wipers self park with push button. in Electrical & WiringDid that. It's not as simple as apply 12 volts or ground during park. Tried all that. Once you turn Rain-gear switch off All the wire (high, low...5 replies | 297 view(s)
-
4 Hours AgoOk, good info..also need to add some clarity to my earlier post. I've always had the ridetech filler but plan on adding a vent in the neck also. So...16 replies | 669 view(s)
-
4 Hours AgoNice project and my favourite Tri Chevy1 replies | 172 view(s)
-
5 Hours AgoLONOVE Soldering Iron Station Kit......130 replies | 19099 view(s) -
5 Hours AgoCurious if anyone on here has run the KRE High Port Heads and Northwind intake on a 2nd Gen Trans Am and what the clearance with the hood is like. I...0 replies | 33 view(s)
-
5 Hours AgoA lot of odd things being stated here imho. Measuring things without the negative of the battery connected is a bit odd and really doesn’t give...1 replies | 52 view(s)
-
6 Hours Agodhutton replied to a thread Drive Line Angles on Lowered 1968 LeMans (A-Body) in General Drive Train TechRaise the transmission. Listen to Andrew.... Don2 replies | 77 view(s)
-
9 Hours Agotbal replied to a thread LSA what mods? LSA into 70 Camaro swap question / parts in Advanced Tech & Performance DiscussionAlmost there ; still hesitant to order ; Pulley run a Griptec 2.40 upper? and 9.55 lower? (will it clear stock sub?) Have to change lower? Hub...33 replies | 863 view(s)
-
11 Hours AgoHi All Looking for any ideas, the other day I forgot (DA) to disconnect my battery and shorted the starter cable/battery feed. No fuses blown....1 replies | 52 view(s)
-
11 Hours AgoOK thanks. Then just start cutting and welding2 replies | 293 view(s)
-
15 Hours AgoStill a 285/40 in the back, but it has 255/40 in the front in these photos.2 replies | 81 view(s) -
15 Hours AgoC5 brakes as well, 18x9 front and rear. 255/45 and 285/40 in this photo. Not a 71-72 obviously, hope this helps.2 replies | 81 view(s)
-
16 Hours AgoStill haven't gotten the bolts out, but haven't really tried. Today was super busy with having to juggle four tuning customers, but I did did get a...176 replies | 11418 view(s) -
16 Hours Agoloudandproud replied to a thread C1500 Full Protouring Chassis Build, Twin Turbo LS Swap in Project UpdatesMid pipe is in. Shes tucked in there pretty nice. Im happy with it. I almost currently going back and fixing up the weld on the hot side that...162 replies | 27216 view(s) -
16 Hours AgoWith the Recaro's here, I am selling the original bucket seats, they're in perfect condition and come with tracks and hardware. $1K, located in the...75 replies | 6257 view(s)
-
16 Hours AgoSelling a pair of perfect original 1969 bucket seats with tracks and hardware for $1k. I purchased some Recaros for my build which is why I am...0 replies | 94 view(s)
-
16 Hours Agoloudandproud replied to a thread C1500 Full Protouring Chassis Build, Twin Turbo LS Swap in Project Updateshttps://youtu.be/eLjXB6PEgKs How many of you guys are running cats on your build? I just got wrapped up with welding up a set of midpipes with...162 replies | 27216 view(s)
-
16 Hours AgoI have no problems during filling with my tank. In fact I filled it today all the way to the top with no spillage or back flow with no slowing of...16 replies | 669 view(s) -
16 Hours AgoAll those details make a difference, so now it sounds like you know what you will have to do. :) I believe the open lug versions are lighter...4 replies | 232 view(s) -
18 Hours AgoHey guys and gals.. show me ur wheels on ur 71-72 cutlass s.... I’m looking to put 18’s on and trying to get some ideas on looks and measurements. I...2 replies | 81 view(s) -
19 Hours AgoSale Pending guys Thanks!!5 replies | 1005 view(s)
-
19 Hours AgoI tested out a couple other starters. Some fit. Some didn't. As I said early, any of the domed starters (I don't know what to call these) just didn't...15 replies | 782 view(s) -
19 Hours AgoAmen, Car and Garage looking very good!632 replies | 196429 view(s)
-
19 Hours AgoSpoke with Forgeline to get more details and spoke with Nick again as well. Forgeline basically said they can do anything I want and I immediately...4 replies | 232 view(s)
-
20 Hours AgoThe Jury started a thread Drive Line Angles on Lowered 1968 LeMans (A-Body) in General Drive Train TechHi All, I thought I would drop in from being a long time lurker to see if you all might be able to help me chase down a driveline angle issue on...2 replies | 77 view(s)
