Activity Stream
-
Older Activity
-
4 Hours AgoTANKMASTERJ replied to a thread Pro-Touring 1971 Camaro - LS376/BowlerTKO600/RideTech/Wilwoods/etc. - Turn Key in For Sale - CarsGLWS I love the green5 replies | 1657 view(s) -
4 Hours AgoSounds like your battery is junk. Put your trickle charger back on it and when it says fully charged take the battery to your local parts store and...1 replies | 40 view(s) -
4 Hours AgoThere was zero change when swapping the leaf springs so it isn't the leaf springs. For giggles I would disconnect the shocks, give it a bounce or...6 replies | 205 view(s)
-
5 Hours AgoI have a 68 Chevelle with a LS3 cruise and connect kit installed. I’ve learned I have a battery draw somewhere so the battery basically dies. Voltage...1 replies | 40 view(s) -
5 Hours AgoIt makes sense with tge difference in the arch of the leaf springs (even if I don't really undersrand the physics of it) What can I do to correct...6 replies | 205 view(s)
-
6 Hours AgoThat is wrong. Side with the lowering block is compressing the spring less, side without the lowering block is compressing the spring more. If...6 replies | 205 view(s)
-
6 Hours AgoOk thanks Donny. Don13 replies | 484 view(s) -
6 Hours Agodontlifttoshift replied to a thread Reasonable price for 4 link install in Open (Pro-Touring) DiscussionNot the same sound. The "happens on downshifts" gave it away. I was convinced something was broken in my car and it was top drivers bar, forward...13 replies | 484 view(s)
-
8 Hours AgoInteresting. There was a couple of threads about this and no one mentioned this, including former Ridetech employees…. Don13 replies | 484 view(s)
-
8 Hours AgoI measured at wheel lip and rocker If I put a lowering block on one side I put more weight on the side with the lowering block I think, no ? ...6 replies | 205 view(s)
-
8 Hours Ago[email protected] replied to a thread Reasonable price for 4 link install in Open (Pro-Touring) DiscussionEven if the shocks did bottom out, you wouldn't get a bang with these really, you'd feel it for sure though. It's 100% what Donny is leaning towards....13 replies | 484 view(s) -
9 Hours AgoI remember this intake from PY Forums I think! Whatever happened to it? So cool!!12 replies | 8237 view(s) -
11 Hours AgoHi All, This past year I developed a IR manifold for Pontiac engines. I currently have an 8 stack setup using Weber 48 IDFs on DCI Motorsports Ram...12 replies | 8237 view(s) -
11 Hours AgoWhen you install one lowering block you put more corner weight on the opposite side. If you put more weight on the opposite side you then have less...6 replies | 205 view(s)
-
11 Hours Agodontlifttoshift replied to a thread Reasonable price for 4 link install in Open (Pro-Touring) DiscussionGet your wrenches out and tighten all hardware that attach the links to anything. Like 120 ft/lbs tight.13 replies | 484 view(s)
-
15 Hours AgoIt seems to me that using a lowering block on one side isn’t a great option, and might be why it isn’t quite lowering the car as it should. Could be...6 replies | 205 view(s) -
15 Hours AgoSounds like the infamous Ridetech bang. This has been discussed before. I think the shocks might be bottoming or topping out. It happens in abrupt...13 replies | 484 view(s)
-
15 Hours AgoYou might be right, it may be easier to just swap out the links. I ordered a complete new one because I have a banging in the rear end and I think...13 replies | 484 view(s)
-
16 Hours Agoryeguy2006a replied to a thread ZL1 Slave Cylinder with Tick Billet Support Sleeve in For Sale - Parts$175 shipped!2 replies | 366 view(s) -
23 Hours AgoThere are definitely enough 1st gen Camaros here for them to make. There could be more than XA to XC Falcons3 replies | 252 view(s) -
1 Day Agostill available if you’re interested13 replies | 1254 view(s)
-
13 replies | 1254 view(s)
-
1 Day Agodanielburko replied to a thread Pro-Touring 1971 Camaro - LS376/BowlerTKO600/RideTech/Wilwoods/etc. - Turn Key in For Sale - CarsJust put 4 new Nitto tires and a new tilton internal slave on the car. Gonna be headed out to the 2023 hot rod power tour on 10 days. Asking...5 replies | 1657 view(s)
-
1 Day AgoBelltech 2" drop spindles 1964 - 1974 Buick, Chevy, Pontiac New $2850 replies | 89 view(s)
-
1 Day AgoI've read a bunch of threads across the internet today regarding mechanical brake sensor orientation. This is the most clear/logical explanation of...2 replies | 595 view(s)
-
1 Day AgoNiagara region here. St. Catharine’s. 69 Firebird coupe and 69 Firebird convertible182 replies | 116737 view(s)
-
182 replies | 116737 view(s)
-
1 Day AgoBlown353 replied to a thread C6 X-Tracker SKF 33 spline hubs, also C5 hubs, both with ARP studs in For Sale - PartsSorry, I hadn't checked in here for a couple of weeks and even though I am subscribed with email notifications I didn't receive one about your post...13 replies | 1626 view(s) -
1 Day AgoI'll let you know if jwcarguy doesn't buy it13 replies | 1254 view(s)
