Activity Stream
-
Older Activity
-
4 Hours AgoReceived some requests for interior shots. The drivers seat will be a Sparco GT seat exactly like the passenger side. Dash is the original Daytona...4 replies | 597 view(s) -
4 Hours AgoSOLD_ Thank you so much Anthony- Will get these shipped out to you tomorrow. Thanks to everyone interested who reached out-6 replies | 1080 view(s)
-
8 Hours AgoLove it, good luck with the sale4 replies | 597 view(s)
-
9 Hours AgoLangleyEleanorBC started a thread Just purchased a full ride tech suspension kit, how many hours to install it ? A eta? in SuspensionOne shop quoted me 40 hours @135$ a hour someone else quoted me 8-14 hours , does anyone have experience with this kit and knows how many...0 replies | 33 view(s)
-
10 Hours AgoExactly. Make a failure essentially non-credible, with good routing practices, double insulation where necessary, heat shielding where necessary,...46 replies | 77599 view(s) -
11 Hours AgoMoney sent, thank you.6 replies | 1080 view(s)
-
11 Hours AgoThank you!6 replies | 1787 view(s) -
11 Hours AgoC Presley replied to a thread Ridetech's New 67-69 F Body Subframe in New Products and Product ReviewsJosh, which headers work best with the Ridetech Subframe? Ultimate Header's, Speed Engineering? Are there other brands that are compatible? Please...59 replies | 16329 view(s)
-
14 Hours AgoSorry guys I screwed the pouch on this, the car is up and running for a while now. Andrew did my tune he said based off data log at 12 pounds of...242 replies | 50980 view(s)
-
16 Hours AgoThank you. It's taken about 8 months to dial in the car to my liking. It really just needs carpet and some small finishing touches to complete.4 replies | 597 view(s)
-
16 Hours AgoSale Pending currently -6 replies | 1080 view(s)
-
17 Hours AgoIDS_Bill started a thread Aeromotive foam or going without? in Advanced Tech & Performance DiscussionHey Everyone, I have a 67 Camaro with an LS3 (@blueshift_camaro on IG) and I was chasing an issue where it wouldn’t rev past 4000 at WOT. I...0 replies | 345 view(s)
-
21 Hours AgoGreat Car! Good luck with the sale! Would cost much more than the asking price to build this.4 replies | 597 view(s)
-
21 Hours AgoWould u ship them for that prize to 93035. Thanks6 replies | 1080 view(s)
-
21 Hours Agodontlifttoshift replied to a thread Haltech, Dakota Digital and complete chasis harness. Where to start? in Electrical & WiringCouple unrelated things. The upper ball joint is on the wrong side of the plate in the upper control arm, it goes in from the top. Your brake...4 replies | 1044 view(s) -
1 Day AgoSwapped67 replied to a thread Haltech, Dakota Digital and complete chasis harness. Where to start? in Electrical & WiringYes they do. That is what I ordered and it may be what I have. I got a lot of parts in at once so I’ll double check later. I’m pretty sure the part #...4 replies | 1044 view(s)
-
1 Day Ago$52,000 Located in Phoenix AZ Clean title The time has come to sell my 1964 Chevy Nova. I have owned the car for 6 years. We just won the...4 replies | 597 view(s)
-
1 Day AgoThe car is in the paint booth right now so I hope to have it back in a week or two. I’ve got a ton of assembly to do when I get it back to the house...16 replies | 8495 view(s) -
1 Day Agoandrewb70 replied to a thread Haltech, Dakota Digital and complete chasis harness. Where to start? in Electrical & WiringDoesn't Dakota Digital make a Haltech specific BIM module? Andrew4 replies | 1044 view(s) -
1 Day AgoMy recently acquired 16 SS and my son's 17 SS. I only wish I had a 1st gen as well360 replies | 305079 view(s) -
1 Day AgoReplies sent to PM's-6 replies | 1080 view(s)
-
1 Day AgoThis is still my favorite build of all the ones I've seen, the fabricators and how they did their mods are something to admire. A+ Mike243 replies | 167817 view(s) -
1 Day AgoWell I'm another one now doing this.. Makes sense to have it with all that we have into our cars. Can't tell in the picture where you wired the...46 replies | 77599 view(s) -
1 Day AgoSounds good. Thanks for your feedback!!12 replies | 5905 view(s) -
1 Day AgoMessage sent.6 replies | 1080 view(s)
-
1 Day AgoIt's been a while since I've been back into the swing of things and got some work done to the car. I've been collecting parts, buying/selling, house...207 replies | 65146 view(s) -
1 Day AgoWelcome to the site. Thanks for joining us.1 replies | 596 view(s) -
1 Day AgoCertainly less time than the old one but I haven't done a new one. ~40 hours if you are straightening a housing, rerouting tail pipes, replumbing...12 replies | 5905 view(s)
-
1 Day AgoI have the bowler night stick shifter, I have added the Tick splash shield, and also installed a hurst base gasket, which has an o-ring printed into...10 replies | 2978 view(s)
-
1 Day AgoJustJohn replied to a thread Haltech, Dakota Digital and complete chasis harness. Where to start? in Electrical & WiringI'm just coming to the end of basically the same job. Do one thing at a time and check your circuits as you go with a 12V power supply. A cheap 30...4 replies | 1044 view(s)
