Activity Stream

I have about $2500 set aside for the suspension on my 67 el camino. As it sits currently it has poly bushings throughout, boxed rear control arms,...

Just a bit on the car, I found it locally knowing full well these type of projects take time and money. My plan is to build a pro turning type car...

1969 Charger Project Car Viper TT motor, 6-spd, Art Morrison Frame, IRS, Wilwood, etc. I am selling a deep dive project. This is not for the...

Looking at the complete kit from Ridetech 11240201 for my 71 Chevelle project. Wondering if anyone has any experience with the whole kit installed. I...

After using the collective knowledge gathered here so many times, I though I would contribute back and show you an unusual build. The car is...

I am thinking of selling my 1966 Nova project due to shoulder surgery and being laid up for awhile. 1966 Nova real SS. Real 118 SS All...

There is a neighborhood on the east side of Winnipeg called Transcona. Long renowned for where a young man could go to get experience at the hands of...

Just looking for experienced opinions... Currently running on my 67 Camaro, 17x8 wheels with 255-50 and 245-45 Nitto NT555-G2 tires. Curious...

Asking on behalf of a friend. 69 Camaro with 555ci Big Block Chev with Holley Super Sniper fuel injection. Engine specs and dyno sheets attached. ...

I hate my tuner.. after tuning my HCIE LS3, I have broken my diff twice in the last week. Here is what I got: 1. 1967 PT Camaro, 500RWHP NA...

I'm very curious about this. I don't think I need a full 4 inch raise. I do think a 2 inch could suffice for my needs. 3 inch on the track and 5 on...

I'm running a drive by wire setup on my 69 Camaro, LS7 with Nick Williams 102mm TB, Holley Terminator X Mac ECU and a T56 transmission. Is there a...

Does anybody know what the technical term is for this? I have my car raised up and need large graphing paper to lay under my car. I am trying to find...

I probably saved this thing from the crusher it was pretty rough, but that has never stopped me before. I got this car about 4or 5 years ago traded...

Guys, not sure if this is the best place to post this but I'm looking for some resources on learning about the Chevy 1947 - 1953 Advance Design...

I've been searching, and it seems that there are two different -AN styles for hard lines. Compression fittings that use a brass ferrule and the 37...

Hi everyone, Looking for a driver quality vehicle. Prefer something from the list below with the Chevelle being number one on it. I might...

I know, good and cheap don't go together but, I need a double flare tool that I'll probably only used a couple times. I need one that I can do the...

BLUF: Why do I always have to modify dapper lighting housings to fit? I love the look and quality of their products, but not a single one has ever...

Brand new Speedtech performance adjustable rear upper and lower control arms. These are single adjustable and articulate to reduce the bind found in...

Decided not to reuse after painting. The park brake handle has been modified to work with Lokar parts and has a custom Cable Craft cable. Make me...

I have a Moser Full float grand national axle. The drive flanges hav 3.06” diameter center hubs where the wheel center mounts instead of the typical...

Have been a long time lurker/member finally pulling the trigger on a build. Set a budget of $30K to get the car running and driving. Picked this car...

Does anyone know what pound springs are normally used for front coilovers on a first fen camaro with an ls motor. I bought my kit years ago and I...

Lets see if Im asking this correctly, when using the Nick Williams TB on a Holley Terminator X Max which TB should be selected from the drop down for...

Following my engine swap I determined that the driveshaft was WAY to close to the driveshaft tunnel. This was confirmed the first time a iAd a...

Unused project parts. New DSE Selecta Speed Wiper kit, $475 will split PP fees and shipping. PM me

Please message me or text me with anything you got for sale under 40k . Ready to buy