Activity Stream
-
Older Activity
-
18 Minutes Agoglr0212 started a thread LT4 crate motor Prices - Are there any deals out there? in Open (Pro-Touring) DiscussionI've been looking for an LT4, every year the price goes up for the crate motors. At one time, a few years ago there was variation in the prices you...0 replies | 0 view(s) -
24 Minutes AgoWhere are you located?1 replies | 101 view(s)
-
41 Minutes Ago[email protected] replied to a thread Ride Tech lower 4 link bar change for more wheel and tire clearance?? in SuspensionThe smaller end on the bar you currently have is 1 3/4" as well so you wouldn't see anything different there. You could upgrade to the R-Joint bars...4 replies | 66 view(s) -
45 Minutes Agobuilttodrive replied to a thread Ride Tech lower 4 link bar change for more wheel and tire clearance?? in SuspensionThey sell a complete r joint bar kit. When I called them they didn't have much to say about it other than I could possibly try adding R-joint ends...4 replies | 66 view(s) -
1 Hour AgoPretty sure it would be around $358 replies | 527 view(s) -
1 Hour AgoWe did Vintage Air, Dakota Digital and Ring Bros interior pieces in this. Finishing up the dash mods and wiring now. Swapped the seats for some...5 replies | 1638 view(s)
-
1 Hour AgoWhat suburb are you from?1 replies | 27 view(s) -
1 Hour AgoYou just have to drill one hole, not very complex. It’s just a clearance hole for the motor, position is not critical. As I said, the Retro...6 replies | 118 view(s) -
1 Hour Agodhutton replied to a thread Ride Tech lower 4 link bar change for more wheel and tire clearance?? in SuspensionI thought they made offset bars for wider tires. Give them a call. Don4 replies | 66 view(s)
-
4 Hours AgoNot sure if they included templates for 69RS. I did 67 & 68's. Here is the instructions... Retro-Electro instructions, PN-004 (retro-electro.net)...6 replies | 118 view(s) -
7 Hours Ago130fe replied to a thread Ride Tech lower 4 link bar change for more wheel and tire clearance?? in SuspensionMaybe they have an R-joint bar configuration that might help.4 replies | 66 view(s) -
8 Hours AgoHi Carl we contacted EFI Hardware, the part no for the module is 92509013 which is for our Holden supercharged 6.2l model When I look on line I...16 replies | 529 view(s) -
9 Hours AgoGlad to help Ryan, and thanks for your trust. Call anytime with questions.1 replies | 72 view(s) -
10 Hours AgoThanks for the link to EFI Hardware. I believe it solves the mystery. This is a snippet of the photo listed on the EFI Hardware site. Note the...16 replies | 529 view(s)
-
10 Hours AgoHey I’m a new member from the Chicago area. I have a 68 Camaro that I’ve owned for 20+ years. The car has been through a few changes and yet again...1 replies | 27 view(s)
-
10 Hours AgoPart number is 6023. - - - Updated - - - Replied - - - Updated - - -3 replies | 200 view(s)
-
10 Hours AgoAnyone else have pics to share? I am in the process of building my cage now and the pics help a ton!32 replies | 10694 view(s)
-
10 Hours AgoOne after the muffler, and one in front of the tips. I'm also running a small flex pipe at the header flange, no issues.4 replies | 78 view(s) -
10 Hours Agoclassiccarcustoms replied to a thread Just another 69 Camaro, DSE LS427 twin turbo in Project UpdatesA couple more47 replies | 6128 view(s)
-
11 Hours AgoHutch69 replied to a thread TCI torque arm rear suspension w/ currie 9" for 67 - 69 Camaro in For Sale - PartsSorry it sold a few years ago.9 replies | 1741 view(s)
-
11 Hours Agobuilttodrive started a thread Ride Tech lower 4 link bar change for more wheel and tire clearance?? in SuspensionI was looking at changing out my current wheels and tires on my 70 Mustang and thinking about going one step wider in the back but I'm only about...4 replies | 66 view(s)
-
11 Hours AgoNo worries on the remote mount thing. YEEAAAAAAAAAAAAA! One of the funniest cartoons out there. If anyone wants to watch it, watch it in...186 replies | 33951 view(s) -
11 Hours AgoA rear crossmember was fabricated to go up and over the drive shaft and fit under the tunnel. The floor pans are fitted and will be installed after...88 replies | 12131 view(s) -
12 Hours AgoPM me a price and any photos you have.4 replies | 909 view(s) -
12 Hours AgoDoes the retro kit come with a template on where to cut the inner fenders such as the DSE?6 replies | 118 view(s)
-
12 Hours Agoi have a couple chevelle's a southern shell very solid, one with with a bunch of new metal already installed just ready for body work. if you still...4 replies | 909 view(s) -
12 Hours Agosold1 replies | 113 view(s)
-
12 Hours AgoEndGame replied to a thread New guy in Michigan... soon to be Texas. in Welcome To Our Message BoardThanks, it's exactly the way I want to keep it minus the RS-0E1 wheels from Forgeline like slimjim mentioned. I want it to be as unsuspecting as...4 replies | 86 view(s) -
12 Hours AgoEndGame replied to a thread New guy in Michigan... soon to be Texas. in Welcome To Our Message BoardDamn man that's exactly what I'm going with! Thanks for the kind words.4 replies | 86 view(s)
-
12 Hours AgoHere is a few Finished Pics of the CaSSaNova project. LSX Procharged with a Stacked By pass system. Full Custom paint and Int. Sony audio system,...2 replies | 374 view(s)
